699459
36
Zoom out
Zoom in
Previous page
1/42
Next page
34 VERSA SATEL
Edit users – when the option is enabled, the person using the service code can add, edit and
remove users.
Arm/Dis/Clr/Bps – when the option is enabled, the person using the service code can arm
and disarm the system, clear alarms, and bypass zones (inhibit or isolate).
6.22.2 Defining the service access time
The function is available when the PERMANENT ACCESS option is disabled (see: “Defining the
service access rules”).
Enter the user menu and press in turn . The number of remaining hours
will be displayed, during which the access to the alarm system is still possible by using the
service code. Enter a new value from the range of 0 to 255 hours and press
.
6.22.3 Replacing batteries in wireless keypad
The function is available if a wireless keypad is installed in the alarm system. The function is
supported by ACU-120 / ACU-270 controller with firmware version 5.03.
1. Enter the user menu and press in turn
.
2. Keep pressing or until the name of the keypad in which you want to replace
the battery is displayed.
3. Press . The status of tamper switch in the keypad will not be checked for 3 minutes,
which allows you to replace the battery.
7. Operating the alarm system by means of keyfob
The alarm system can be operated by means of keyfobs, if the 433 MHz keyfobs receiver
expansion module (INT-RX-S / INT-RX), 433 MHz wireless system controller (VERSA-MCU)
or ABAX wireless system controller (ACU-120 / ACU-270 / ACU-100 / ACU-250) is
connected to the control panel.
The user can have two keyfobs:
433 MHz keyfob – supported by the 433 MHz keyfobs receiver expansion module or 433
MHz wireless system controller,
APT-100 bidirectional keyfob – supported by the ABAX wireless system controller.
A single keyfob enables up to 6 functions to be executed. The list of functions assigned to the
buttons / combination of buttons should be obtained from the person who configured the
keyfob settings when adding / editing a user. In the case of APT-100 keyfob, that person
should also provide information about functionality of the LEDs. The keyfob LEDs can be
used to confirm execution of functions, as well as to indicate the system status (pressing
a button on the APT-100 keyfob is accompanied by the LEDs flashing rapidly three times,
and in a little while the LED(s) may come on for 3 seconds to provide information).
The installer can configure the alarm system so that the sirens connected to the
system outputs can inform the user about the following events:
1 tone – starting the arming procedure (which is equivalent to arming, if the exit delay
has not been programmed),
2 tones – disarming,
4 tones – alarm clearing,
7 tones – arming is not possible, or the arming procedure has failed.
Tone duration is approx. 0.3 seconds.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel VERSA 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel VERSA 10 in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel VERSA 10

Satel VERSA 10 Quick start guide - English - 11 pages

Satel VERSA 10 Additional guide - English - 87 pages

Satel VERSA 10 Installation Guide - English - 36 pages

Satel VERSA 10 User Manual - English - 32 pages

Satel VERSA 10 Quick start guide - German - 11 pages

Satel VERSA 10 Additional guide - German - 89 pages

Satel VERSA 10 User Manual - German - 44 pages

Satel VERSA 10 Installation Guide - German - 37 pages

Satel VERSA 10 Quick start guide - German - 2 pages

Satel VERSA 10 Quick start guide - Dutch - 11 pages

Satel VERSA 10 User Manual - Dutch - 44 pages

Satel VERSA 10 Quick start guide - Dutch - 2 pages

Satel VERSA 10 Additional guide - Dutch - 86 pages

Satel VERSA 10 Installation Guide - Dutch - 35 pages

Satel VERSA 10 Quick start guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info