699466
19
Zoom out
Zoom in
Previous page
1/27
Next page
SATEL PERFECTA 17
4. When the cursor shows the S
ERVICE MODE
function, press .
5. Service mode menu will be displayed (the cursor will show the E
ND
SM function).
6.9.5 Emergency procedure of the control panel start-up
If the control panel fails to start properly, keypads are not supported, codes are not accepted
by the control panel etc., despite all connections having been made correctly, follow the steps
below:
1. Turn off the control panel power supply (first disconnect the AC power, and then the
battery).
2. Put a jumper on the RESET pins.
3. Turn on the control panel power supply (first connect the battery and then the AC power).
4. Wait a few seconds (until LEDs next to the RESET pins stop blinking) and remove the
jumper from the RESET pins. The control panel will enter the service mode. The service
mode menu will be displayed on the wired keypad with the lowest address.
If there is no wired keypad in the alarm system or there is no communication with the
wired keypads (e.g. when the communication bus is shorted), you can get access to
the service mode menu from the wireless keypad with the lowest address. Press any
key on this keypad within 30 seconds of removing jumper from the RESET pins.
The service mode menu will not be displayed, if the D
ISABLE
S
ERVICE
M
ODE
option is
enabled in the control panel. The “Factory settings ? 1=Yes” message will be
displayed on the keypad with the lowest address. You can press to restore the
factory default settings. The service mode menu will not be displayed until the factory
settings are restored.
6.9.6 First steps after starting-up the control panel
Control panel with wired keypads
If wired keypads are connected to the control panel, then, after starting the control panel with
factory settings:
1. Set correct, individual addresses in the wired keypads.
2. Run the function of identification of devices connected to the communication bus of the
control panel.
Control panel without wired keypads PERFECTA 16-WRL / PERFECTA 32-WRL
If no wired keypads are connected to the control panel, then, after starting the control panel
with factory settings:
1. Connect computer to alarm control panel.
2. Use the PERFECTA
S
OFT
program to add wireless keypads.
3. Run the function of identification of devices connected to the communication bus of the
control panel.
6.10 Programming addresses for the hardwired keypads
An individual address from the 0 to 3 range must be set for each keypad. By default, address
0 is preset for all wired keypads. After starting the alarm control panel with factory default
settings, all keypads connected to the bus are supported, no matter what their addresses are.
This allows you to program individual address for the keypads.
Remember to program an individual address if a new keypad is connected to the
already functioning alarm system.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel PERFECTA 32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel PERFECTA 32 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel PERFECTA 32

Satel PERFECTA 32 Quick start guide - English - 10 pages

Satel PERFECTA 32 User Manual - English - 31 pages

Satel PERFECTA 32 Additional guide - English - 49 pages

Satel PERFECTA 32 Additional guide - English - 50 pages

Satel PERFECTA 32 Quick start guide - German - 11 pages

Satel PERFECTA 32 User Manual - German - 32 pages

Satel PERFECTA 32 Additional guide - German - 52 pages

Satel PERFECTA 32 Additional guide - German - 50 pages

Satel PERFECTA 32 Installation Guide - German - 28 pages

Satel PERFECTA 32 Quick start guide - Dutch - 11 pages

Satel PERFECTA 32 User Manual - Dutch - 32 pages

Satel PERFECTA 32 Additional guide - Dutch - 52 pages

Satel PERFECTA 32 Additional guide - Dutch - 50 pages

Satel PERFECTA 32 Installation Guide - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info