699537
17
Zoom out
Zoom in
Previous page
1/47
Next page
SATEL PERFECTA LTE 15
Hide arm state indication after [125.Suppr.arm] – time counted from the moment of
partition arming, after which the LED on keypad indicating the partition armed status goes
off. If value 0 is programmed, the LED will be ON always when the partition is armed.
4.1.3 Arming
Prevent arming if not ready [Check if ready] – if this option is enabled, the control panel will
perform a check during arming for any problems that may prevent arming the system.
These include:
a zone with enabled P
RIORITY
option is violated in the partition,
– the 3. I
NSTANT
, 4. D
OUBLE KNOCK
, 5. 24
H
B
URGLARY
, 7. 24
H
P
ANIC
, 8. 24
H
P
ANIC SILENT
,
9. 24
M
EDICAL
or 10. 24
H
F
IRE
type zone is violated in the partition,
– the 3. I
NSTANT
, 4. D
OUBLE KNOCK
, 5. 24
H
B
URGLARY
, 7. 24
H
P
ANIC
, 8. 24
H
P
ANIC SILENT
,
9. 24
M
EDICAL
or 10. 24
H
F
IRE
type zone or a zone with enabled P
RIORITY
option is
bypassed in the partition,
there is a tamper in the partition,
there is a trouble in the system.
The control panel checks the conditions twice:
before starting the arming procedure – the control panel will not start the arming
procedure, if any problems occur (the keypad provides a forced arming option – see
U
SER MANUAL
),
after finishing the exit delay countdown – the system will not be armed (the arming
procedure will end in failure), if there are any problems, which did not occur before
starting the exit delay countdown.
If the option is enabled and a zone of the 0. E
NTRY
/E
XIT
, 1. E
NTRY
/E
XIT FINAL
or 2. I
NTERNAL
type is violated at the moment the exit delay countdown expires and the partition is armed,
a warning alarm will be triggered. If the partition is not armed after exit delay countdown
expires, the warning alarm will not be triggered.
Arm even if not ready after exit delay [Arm ExDly w.trbl] – if this option is enabled, the
control panel will not check conditions after finishing the exit delay countdown (it will only
check the conditions before starting the arming procedure). The option is available, when
the P
REVENT ARMING IF NOT READY
option is enabled.
Do not arm if battery trouble [BAT low = no arm] – if this option is enabled, forced arming
will be impossible in the event of battery trouble. The option is available, when the
P
REVENT ARMING IF NOT READY
option is enabled.
Do not arm if tampered [Tamper = no arm] – if this option is enabled, forced arming will be
impossible in the event of tamper. The option is available, when the P
REVENT ARMING IF NOT
READY
option is enabled.
4.1.4 Options
Service Mode beep [SM sounds] – if this option is enabled, the service mode will be audibly
signaled on the keypad.
Signal trouble state in partial arming [Trbl.in part.arm] – if this option is enabled, the
LED on the keypad goes off after both partitions are fully armed. If the option is disabled,
the LED goes off after just one of the partitions is armed in any mode.
Lock after three incorrect codes [3wrng.codes=blk.] – if the option is enabled, after
entering an incorrect code three times, the keypad will be blocked for 90 seconds. Entering
an invalid code again will prolong the locking.
Entering an invalid code three times may trigger alarm (cf. the keypad A
LARM
3
INCORRECT CODES
option).
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel PERFECTA 32 LTE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel PERFECTA 32 LTE in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel PERFECTA 32 LTE

Satel PERFECTA 32 LTE Quick start guide - English - 10 pages

Satel PERFECTA 32 LTE User Manual - English - 30 pages

Satel PERFECTA 32 LTE Additional guide - English - 50 pages

Satel PERFECTA 32 LTE Installation Guide - English - 26 pages

Satel PERFECTA 32 LTE User Manual - German - 11 pages

Satel PERFECTA 32 LTE Additional guide - German - 50 pages

Satel PERFECTA 32 LTE Installation Guide - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info