699074
20
Zoom out
Zoom in
Previous page
1/35
Next page
18 Installer Manual SATEL
5.6.1 Connecting the INT-VG or INT-AV module or CA-64 SM expander
When connecting the INT-VG voice module, INT-AV audio alarm verification module or the
CA-64 SM voice synthesizer expander, the CLK and DTA wires only are to be connected to
the bus. Each of these devices is additionally provided with the PIN5 connector, which should
be inserted into the control panel onboard socket designated as SYNT1 or SYNT2.
Only one INT-VG module or CA-64 SM expander can be connected to the
INTEGRA 64 Plus control panel, because it allows not more than 16 voice messages
to be played back.
5.6.2 Addressing devices connected to the expander bus
Each device to be connected to the expander bus must have its own individual address from
the 0 to 31 range. The addresses of devices connected to the same bus must not repeat (the
control panel does not support devices having identical addresses). It is recommended that
consecutive addresses be assigned starting from 0. In most devices, the address is set by
means of DIP-switches.
If the device is connected to the second bus, its address in the system can be
determined by adding the number 32 to the address set in it.
The address affects numeration of zones and outputs in the system (see section
NUMERATION OF ZONES AND OUTPUTS IN THE SYSTEM p. 28).
5.7 Connecting the detectors
How the detector is connected to the zone must be suitable for the configuration chosen for
that zone. The zones on the control panel mainboard support the following configurations:
NC the wiring type dedicated to connecting devices with the NC (normally closed) alarm
output. Opening the circuit will trigger an alarm.
NO the wiring type dedicated to connecting devices with the NO (normally open) alarm
output. Closing the circuit will trigger an alarm.
EOL this wiring type may be used to connect devices having the NC or NO alarm output.
Closing or opening the circuit will trigger an alarm.
2EOL/NC the wiring type recommended to connect detectors having the NC alarm output
and a tamper output. The zone can recognize 3 states: normal, alarm and tamper.
2EOL/NOthe wiring type similar as 2EOL/NC, but for detectors with the NO alarm output.
Roller the wiring type dedicated to connecting roller shutter detectors.
Vibration the wiring type dedicated to connecting vibration detectors. The zone will also
accept connection of a detector with the NC alarm output (e.g. a vibration detector and
a magnetic contact can be connected in series).
Follow output in case of this configuration the detector should not be connected. The zone
status depends only on that of the selected output (the output is not to be physically
connected to the zone).
Roller 2EOLthe wiring type similar as 2EOL/NC, but for the roller shutter detectors.
Vibration 2EOL the wiring type similar as 2EOL/NC, but for the vibration detectors.
3EOL/NCthe wiring type recommended for connecting detectors with the NC alarm output,
tamper output and anti-masking output. The zone can recognize 4 states: normal,
alarm, tamper and masking of detector.
3EOL/NO the wiring type similar as 3EOL/NC, but for the detectors with the NO alarm
output.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 64 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 64 Plus in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 64 Plus

Satel Integra 64 Plus User Manual - English - 51 pages

Satel Integra 64 Plus Additional guide - English - 102 pages

Satel Integra 64 Plus User Manual - German - 55 pages

Satel Integra 64 Plus Additional guide - German - 108 pages

Satel Integra 64 Plus Installation Guide - German - 36 pages

Satel Integra 64 Plus User Manual - Dutch - 53 pages

Satel Integra 64 Plus Additional guide - Dutch - 108 pages

Satel Integra 64 Plus Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info