699031
12
Zoom out
Zoom in
Previous page
1/36
Next page
10 Errichteranleitung SATEL
Für die Montage sind folgende Werkzeuge notwendig:
Flachschraubenzieher 2,5 mm,
Kreuzschraubenzieher,
Präzisionszange,
Flachzange,
Bohrmaschine mit Bohrerset.
5.1 Plan der Installation
Vor der Montage bereiten Sie einen Plan des Alarmsystems vor. Es wird empfohlen, einen
Entwurf des Objektes auszuführen und alle Module, die zum Alarmsystem gehören (Zentrale,
Bedienteile, Tastaturen, Melder, Signalgeber, Erweiterungsmodule usw.), auf dem Objekt
zu befestigen. Die Zentralen und andere Bauelemente des Alarmsystems sollten innerhalb
des Schutzbereichs montiert werden.
Bei der Speicherung von Daten im FLASH-Speicher und wenn das Programm
STARTER aktiv ist (Aktualisierung der Firmware der Zentrale), sind die Ausgänge
in den Erweiterungsmodulen ausgeschaltet. Der Zustand der Ausgänge auf
der Platine der Zentrale wird nicht geändert. Beachten Sie das bei
der Systemerstellung. Nach der Aktivierung des Programms STARTER schließen Sie
die Geräte, deren Betrieb während der Speicherung von Daten im FLASH-Speicher
nicht gestört werden soll, an die Ausgänge auf der Hauptplatine an.
5.2 Einschätzung der Stromaufnahme im System
Bei der Planung der Installation eines Alarmsystems zählen Sie den durch alle zum System
gehörenden Module (Hauptplatine der Zentrale, Bedienteile, zusätzliche Module, Melder,
Signalgeber usw.) verbrauchten Strom zusammen. Der Ladestrom des Akkus soll
dazugerechnet werden. Falls die gesamte Stromaufnahme größer ist, als der Ausgangsstrom
des Netzteils der Zentrale, installieren Sie im System Erweiterungsmodule mit eigenem
Netzteil oder ein zusätzliches Netzgerät.
Die gesamte Stromaufnahme der ans Netzgerät (bzw. Erweiterungsmodul mit Netzteil)
angeschlossenen Module darf den Ausgangsstrom des Netzgeräts nicht überschreiten.
Bei der Planung des Anschlusses der Module an die einzelnen Stromversorgungsausgänge
(Zentrale, Erweiterungsmodule mit Netzteil usw.) achten Sie darauf, dass die gesamte
Stromaufnahme der Module die maximale Belastbarkeit der Stromversorgungsausgänge
nicht überschreiten darf.
5.3 Verkabelung
Zur Verbindung der zum System gehörenden Module wird das einfache ungeschirmte Kabel
empfohlen (es wird nicht empfohlen, verdrilltes Kabel UTP, STP, FTP anzuwenden).
Bei der Verwendung eines verdrillten Kabels für den Anschluss der Geräte an
den Datenbus, beachten Sie, dass die Signale DTM und CKM / DT und CK / DT1 und
CK1 / DT2 und CK2 (Daten und Uhr) nicht mit einem Paar verdrillter Leitungen geleitet
werden sollen.
Es wird empfohlen, separate Kabel für Busse der Bedienteile und der Erweiterungsmodule
zu benutzen.
Der Ader-Querschnitt soll so angepasst werden, damit der Spannungsfall zwischen
dem Netzgerät und dem versorgten Modul 1 V im Verhältnis zur Ausgangsspannung nicht
überschreitet.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 256 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 256 Plus in the language / languages: German as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 256 Plus

Satel Integra 256 Plus User Manual - English - 51 pages

Satel Integra 256 Plus Additional guide - English - 102 pages

Satel Integra 256 Plus Installation Guide - English - 35 pages

Satel Integra 256 Plus User Manual - German - 55 pages

Satel Integra 256 Plus Additional guide - German - 108 pages

Satel Integra 256 Plus Quick start guide - Dutch - 2 pages

Satel Integra 256 Plus Additional guide - Dutch - 108 pages

Satel Integra 256 Plus User Manual - Dutch - 53 pages

Satel Integra 256 Plus Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info