699031
66
Zoom out
Zoom in
Previous page
1/102
Next page
64 Programming SATEL
109. ZONES LOGICAL ANDactive, when all zones selected as the control ones are violated.
110. ALARM NOT VERIFIEDsignals unverified alarms.
111. ALARM VERIFIEDsignals verified alarms.
112. VERIFIED NO ALARM informs that the alarm has not been verified (during the alarm
verification no alarm was triggered by any other zone included in the verification).
113. VERIFICATION DISABLED STATUSsignals disabling alarm verification.
114. ZONE TEST STATUS indicates the zone testing by means of user functions.
115. ARMING TYPE STATUSactive when selected partitions are armed in the selected mode.
116. INTERNAL SIREN signals the same alarms and violations as the 1. BURGLARY or 9. DAY
ALARM output type (logic product of the 1. BURGLARY and 9. DAY ALARM outputs).
117. TAMPERING STATUSinforms about tamper of selected zones, keypads and expanders.
118. KEYFOB BATTERY LOW informs about low battery in keyfobs belonging to selected
users. Refers to the 433 MHz keyfobs (supported by the INT-RX or INT-RX-S modules) or
the APT-200 (supported by the ABAX 2 / ABAX system) / APT-100 keyfobs (supported by
the ABAX system).
119. WIRELESS SYSTEM JAMMING indicates the jamming of device supporting the ABAX 2
(ACU-220 or ACU-280 controller) / ABAX wireless system (ACU-120, ACU-270, ACU-100
or ACU-250 controller).
120. THERMOSTAT the output activates when temperature drops below a preset value. The
control panel can receive the temperature data from wireless temperature detectors or
ABAX 2 wireless devices provided with a temperature sensor. For more information, refer
to section 120. Thermostat output parametersp. 66.
121. MASKING signals for a programmed time masking the detectors connected to the 3EOL
zones.
122. MASKING STATUS indicates the masking the detectors connected to the 3EOL zones.
5.3 Options
Pol.+ defines the output operating mode (see Table 5).
high-current output
option enabled
(normal polarity)
option disabled
(reversed polarity)
active status
+12V voltage supply
+12V voltage cut-off
inactive status
+12V voltage cut-off
+12V voltage supply
low-current output
option enabled
(normal polarity)
option disabled
(reversed polarity)
active status
shorted to ground
isolated from ground
inactive status
isolated from ground
shorted to ground
Table 5. Functioning of outputs, depending on the POL.+ option.
Pulsatingthe option refers to timed outputs. If it is enabled, the output operates in
a pulsating mode. If it is disabled, the output operates continuously.
Latch the option refers to alarm outputs. If it is enabled, the output will be active until the
alarm is cleared by the user.
Active during violation the option applies to the 24. MONO SWITCH output. If enabled, the
output is always active when a control zone is violated, and the countdown of output cut-
off time will only be running after the violation ends.
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 256 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 256 Plus in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 256 Plus

Satel Integra 256 Plus User Manual - English - 51 pages

Satel Integra 256 Plus Installation Guide - English - 35 pages

Satel Integra 256 Plus User Manual - German - 55 pages

Satel Integra 256 Plus Additional guide - German - 108 pages

Satel Integra 256 Plus Installation Guide - German - 36 pages

Satel Integra 256 Plus Quick start guide - Dutch - 2 pages

Satel Integra 256 Plus Additional guide - Dutch - 108 pages

Satel Integra 256 Plus User Manual - Dutch - 53 pages

Satel Integra 256 Plus Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info