699079
33
Zoom out
Zoom in
Previous page
1/114
Next page
SATEL INTEGRA 31
analog modem for communication with the external modem of the control panel,
ISDN or GSM modem for communication with the ISDN or GSM modem of the control
panel.
After clicking on the button you can configure the selected set of parameters (see:
Configuring the modem connected to computer”).
Dialing the method of dialing numbers by the modem connected to computer (tone or
pulse).
Dial tones control if option is enabled, the modem connected to computer will detect the
dial tone or busy signal before dialing the number.
Speaker operating mode of the modem speaker. The speaker can be always OFF, or ON
until connection with the control panel is established (auto), or always ON.
Volumevolume of modem speaker.
Answering how the DLOADX program reacts when the control panel is connecting to the
program. Communication can be established automatically after a preset number of rings,
or the program will only indicate an attempt to establish communication by the control
panel (communication will only be established after clicking on the “Answer” button).
Double call you can define duration of the pause between the first and the second call, if
the control panel is set to go off-hook after the second call.
Configuring the modem connected to computer
You can edit the parameters after clicking on the “Change” button.
Port RS-232computer COM port to which the modem is connected.
Modem list of modems, the parameters of which are defined. The list of modems and their
settings will be written to disk in the “modem.ini” file.
Baud Rate transmission rate of the serial port. It is recommended that the highest rate
acceptable by the modem be set (only some modems may require the 300 bps setting in
order to enforce operation with exactly this speed).
Reset command the command to reset the modem. Typically, it is the ATZ command
(reset with restoration of the user's zero profile). Some modems may require using the
AT&F command (reset with restoration of the factory default settings).
Initializing lines containing the modem initialization commands:
for communication with built-in control panel 300 bps modem: in the first line E0V1Q0
a command required for proper operation of the modem. You should also add the
operating mode selection: B0 or B1 (selection of transmission format: V.21 or Bell103),
and the commands limiting transmission rate over telephone line to 300 bps. These are
commands specific for the given modem model, e.g. N0S37=3, F1 or +MS=1,0,300,300
etc. Information on how to limit the modem transmission rate is usually included in the
device manual. The other line should contain the following commands:
S0=0S9=1S7=120S10=255. They are necessary for correct operation.
for communication with external analog modem connected to the control panel: in
the first line E0V1Q0, the second line S0=0S7=120. It is not recommended to insert
additional commands to limit the modem transmission rate, unless this is required by
the modems used, or the telephone link quality.
for communication through ISDN or GSM modem: in the first line E0V1Q0, the second
line S0=0. Depending on the modems used, you will have to use additional
commands to set the identical transmission format, as in the control panel
modem, i.e. specific for the given modem. V.110 format is intended for the GSM
modems.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 24 in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 24

Satel Integra 24 User Manual - English - 51 pages

Satel Integra 24 Installation Guide - English - 36 pages

Satel Integra 24 Quick start guide - German - 2 pages

Satel Integra 24 User Manual - German - 54 pages

Satel Integra 24 Additional guide - German - 121 pages

Satel Integra 24 Installation Guide - German - 38 pages

Satel Integra 24 Quick start guide - Dutch - 24 pages

Satel Integra 24 User Manual - Dutch - 52 pages

Satel Integra 24 Additional guide - Dutch - 121 pages

Satel Integra 24 Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info