699073
92
Zoom out
Zoom in
Previous page
1/114
Next page
90 Programming SATEL
ASW-210
For each position occupied by the controller, enter 0 (relay can only be controlled via the
control panel), 1 (the input enables relay to be controlled with monostable switch) or 2 (the
input enables relay to be controlled with bistable switch).
9.2.2 Configuring the wireless devices – LCD keypad
Having started the CONFIGURATION function (STRUCTURE HARDWARE EXPANDERS
SETTINGS ABAX - INTEGRA. CONFIGURATION), use the and keys to select the zone
to which the do wireless device is assigned and press the
key. Use the arrow keys for
programming. The values which can be programmed for individual parameters of wireless
devices are presented in the section describing configuration of the devices by means of the
DLOADX program.
9.3 Specific character of the operation of wireless devices
This chapter describes the peculiar character of the operation of individual groups of wireless
devices, which affects the method of programming the zones and outputs to which the
wireless devices are assigned.
9.3.1 Wireless detectors
The zone to which a wireless detector is assigned is activated when the detector reports
alarm (select the appropriate zone type). If a detector tamper is to trigger the tamper alarm,
program the zone as 2EOL/NC or 2EOL/NO.
The mode of operation of wireless detectors depends on the status of partition to which the
zone with wireless detector belongs:
partition disarmed the detector operates in passive mode. This operating mode prolongs
the battery life. Detector informs the control panel about its status during polling (only the
tamper information is sent immediately).
partition armed the detector operates in active mode. The detector sends immediately all
information to the control panel.
Because switching the detectors over from the passive into active mode and conversely
takes place during the response time, it is performed with some delay in relation to
arming/disarming. The maximum delay depending on the selected response frequency
can be 12, 24 or 36 seconds.
The wireless detectors assigned to the 24-hour zones, which are permanently armed, are in
the active mode at all times. Also other wireless detectors can always work in the active
mode, if the ALWAYS ACTIVE option is enabled for them (see p. 85).
According to the EN50131-3 standard all ABAX 2 / ABAX Hold-Up devices must be
always in active mode.
The battery life time in the detectors switched permanently into the active mode is
shorter than in those which are periodically switched to the passive mode. However, if
the specific character of a detector or its installation place is such that the number of
alarms is low, switching the detector permanently into the active mode will not have
a significant effect on the battery life.
9.3.2 Wireless sirens
Turning on the output to which the wireless siren is assigned will trigger the signaling.
Depending on the siren:
ASP-105 the first output controls acoustic signaling, and the other one optical signaling.
The command to start or stop the signaling is sent to the siren immediately. The acoustic
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 128 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 128 in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 128

Satel Integra 128 User Manual - English - 51 pages

Satel Integra 128 Installation Guide - English - 36 pages

Satel Integra 128 User Manual - German - 54 pages

Satel Integra 128 Additional guide - German - 121 pages

Satel Integra 128 Installation Guide - German - 38 pages

Satel Integra 128 Quick start guide - Dutch - 24 pages

Satel Integra 128 User Manual - Dutch - 52 pages

Satel Integra 128 Additional guide - Dutch - 121 pages

Satel Integra 128 Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info