699073
68
Zoom out
Zoom in
Previous page
1/114
Next page
66 Programming SATEL
108. CARD ON READER B indicates the proximity card / DALLAS iButton read-in by the
expander reader B. It can also signal card reading in the LCD keypad.
109. ZONES LOGICAL ANDactive, when all zones selected as the control ones are violated.
110. ALARM NOT VERIFIEDsignals unverified alarms.
111. ALARM VERIFIEDsignals verified alarms.
112. VERIFIED NO ALARM informs that the alarm has not been verified (during the alarm
verification no alarm was triggered by any other zone included in the verification).
113. VERIFICATION DISABLED STATUSsignals disabling alarm verification.
114. ZONE TEST STATUS indicates the zone testing by means of user functions.
115. ARMING TYPE STATUSactive when selected partitions are armed in the selected mode.
116. INTERNAL SIREN signals the same alarms and violations as the 1. BURGLARY or 9. DAY
ALARM output type (logic product of the 1. BURGLARY and 9. DAY ALARM outputs).
117. TAMPERING STATUSinforms about tamper of selected zones, keypads and expanders.
118. KEYFOB BATTERY LOW informs about low battery in keyfobs belonging to selected
users. Refers to the 433 MHz keyfobs (supported by the INT-RX or INT-RX-S modules) or
the APT-200 (supported by the ABAX 2 / ABAX system) / APT-100 keyfobs (supported by
the ABAX system).
119. WIRELESS SYSTEM JAMMING indicates the jamming of device supporting the ABAX 2
(ACU-220 or ACU-280 controller) / ABAX wireless system (INTEGRA 128-WRL control
panel, ACU-120, ACU-270, ACU-100 or ACU-250 controllers).
5.3 Options
Pol.+ – defines the output operating mode (see Table 5).
high-current output
option enabled
(normal polarity)
option disabled
(reversed polarity)
active status
+12V voltage supply
+12V voltage cut-off
inactive status
+12V voltage cut-off
+12V voltage supply
low-current output
option enabled
(normal polarity)
option disabled
(reversed polarity)
active status
shorted to ground
isolated from ground
inactive status
isolated from ground
shorted to ground
Table 5. Functioning of outputs, depending on the POL.+ option.
Pulsatingthe option refers to timed outputs. If it is enabled, the output operates in
a pulsating mode. If it is disabled, the output operates continuously.
Latch the option refers to alarm outputs. If it is enabled, the output will be active until the
alarm is cleared by the user.
Active during violation the option applies to the 24. MONO SWITCH output. If enabled, the
output is always active when a control zone is violated, and the countdown of output cut-
off time will only be running after the violation ends.
Timer activates/deactivates the option applies to the 24. MONO SWITCH and 25. BI SWITCH
outputs. If enabled, the output can be controlled by selected timers. Turning the timer ON
activates the output (in case of the 24. MONO SWITCH type output for a programmed
time), and turning the timer OFF deactivates the output.
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 128 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 128 in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 128

Satel Integra 128 User Manual - English - 51 pages

Satel Integra 128 Installation Guide - English - 36 pages

Satel Integra 128 User Manual - German - 54 pages

Satel Integra 128 Additional guide - German - 121 pages

Satel Integra 128 Installation Guide - German - 38 pages

Satel Integra 128 Quick start guide - Dutch - 24 pages

Satel Integra 128 User Manual - Dutch - 52 pages

Satel Integra 128 Additional guide - Dutch - 121 pages

Satel Integra 128 Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info