699073
55
Zoom out
Zoom in
Previous page
1/114
Next page
SATEL INTEGRA 53
2. NOthe zone supports a detector of NO (normally open) type,
3. EOLthe zone supports a detector of NO or NC type with EOL resistor in the circuit,
4. 2EOL/NC the zone supports a detector of NC type with two EOL resistors in the
circuit,
5. 2EOL/NO the zone supports a detector of NO type with two EOL resistors in the
circuit,
6. Rollerthe zone supports a roller shutter detector,
7. Vibrationthe zone supports a vibration detector (also NC type detector),
8. Follow outputthe zone does not support any detectors its status depends solely on
the status of selected output (physical violations and tampers of the zone are ignored).
Zone sensitivity depending on wiring type:
NO, NC, EOL, 2EOL/NC, 2EOL/NOthe time during which the zone must be violated, so
that it can be noted by the control panel.
Roller 2 parameters are to be programmed (in the DLOADX program, you should enter
two numbers in the ZONE SENSITIVITY field):
Pulses duration the time period during which a specified number of pulses must
occur (PULSES COUNT) for the zone to be violated. You can enter 0 (the pulse counter
will only be reset on arming / disarming), 1 (30 seconds), 2 (120 seconds) or 3 (240
seconds).
Pulses count the number of pulses after which the zone will be violated. You can
program values from 1 to 8.
Vibration 2 parameters are to be programmed (in the DLOADX program, you should
enter two numbers in the ZONE SENSITIVITY field):
Sensitivity occurrence of a pulse whose duration is equal to or longer than the
defined time will cause violation of the zone. You can program values from the 3 ms
to 96 ms range (every 3 ms).
Pulses count the number of pulses after which the zone will be violated. You can
program values from 0 to 7. If the value 0 is programmed, the pulses will not be
counted only SENSITIVITY will be taken into account.
Output refers to the FOLLOW OUTPUT wiring type. Indicate the number of output whose
activation will violate the zone. The output can be a virtual one.
Max. violation time / Max. door opening time exceeding the maximum time of
violation/door opening is recognized by the control panel as a detector failure/door failure.
If the value 0 is programmed, control of this time is disabled.
Max. no violation time exceeding the maximum time of no violation is recognized by the
control panel as a detector failure. The time will only be counted when the zone is
disarmed. If the value 0 is programmed, control of this time is disabled. The time can be
programmed in hours or minutes.
It is recommended that you program the MAX. NO VIOLATION TIME parameter, since it will
provide an additional supervision of the detector connected to the zone.
4.3.5 Zone types
0. ENTRY/EXIT a delayed zone combining two functions:
entry violation of the zone starts entry delay counting in the partition and turns on delay
for the 3. INTERIOR DELAYED type zones,
exitviolation of the zone during exit delay countdown is equivalent to the partition exit.
1. ENTRY violation of the zone starts entry delay counting in the partition and turns on delay
for the 3. INTERIOR DELAYED type zones.
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 128 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 128 in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 128

Satel Integra 128 User Manual - English - 51 pages

Satel Integra 128 Installation Guide - English - 36 pages

Satel Integra 128 User Manual - German - 54 pages

Satel Integra 128 Additional guide - German - 121 pages

Satel Integra 128 Installation Guide - German - 38 pages

Satel Integra 128 Quick start guide - Dutch - 24 pages

Satel Integra 128 User Manual - Dutch - 52 pages

Satel Integra 128 Additional guide - Dutch - 121 pages

Satel Integra 128 Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info