699607
9
Zoom out
Zoom in
Previous page
1/20
Next page
CA-5 SATEL 7
5. enter the code [1][2][3][4][5] from the keypad (the code is to be entered within 15
seconds of removing the jumper) and terminated by pressing the key [#] or [
*
].
After completion of the a.m. operations, the control panel should return to its default
settings and stay in the service mode.
With the option 2 selected, violation of the 24H
TAMPER
zone type NO, NC, EOL, or
violation of this zone tamper circuit in the 2EOL configuration, when the control panel is
disarmed, will be alarm signaled in the keypad only. On the other hand, normal violation
of the 2EOL 24H
TAMPER
zone (activating the detector) will set off audible alarm,
irrespective of this option setting.
This option does not refer to keypad tampering. If the keypad is cut off when the control
panel is disarmed, the alarm will be signaled on the alarm outputs (audible alarm).
The option 3 – 3 minutes after the system has been armed, the keypad stops indicating
the armed mode status.(
[
ARMED
] LED is off) The indicator lights up again when one of
the zones is violated, or when tamper alarm is triggered.
The option 4 should be enabled if test transmissions are conducted frequently. Only 3
successive events of the test transmission are then saved in memory. Next transmissions
will not be saved, thus preventing the events memory of the control panel from being
quickly filled up. Occurrence of any event other than test transmission will reset the
blocking and activate event saving, which means that next three test transmissions can be
written to the memory.
The option 5 limits the number of saved alarms triggered by one zone down to 3 in time
intervals shorter than 1 minute. The option 5 limits the number of events generated in the
system by reducing the number of alarms triggered by one zone down to 3 in time intervals
shorter than 1 minute. If the control panel, being in armed state, has received 3 violations
from a given zone within a shorter time than 1 minute, then every next violation will be
ignored unless 1 minute has passed since the previous violation.
FS 79 – SYSTEM OPTIONS part 2
LED
No.
Name of option
in LCD keypad
Set
option
Description of option
1 troubles memory x
trouble until the current troubles are reviewed (key 7)
2 alarms memory x
alarm in the zone until the alarm log is reviewed (key 5)
3 new trbl. sign. audible signaling of new trouble
4 OUT1 fr.zn.only.
OUT1 from zone only – blocking acknowledgement on
OUT1 of arming/disarming from the keypad.
5 not used
x
– default
Notes:
Selection of the option 1 results in signaling the trouble (blinking of the [
TROUBLE
] LED)
even after its cause has ceased to exist, until the current troubles have been reviewed
(press and hold down the key 7).
With the option 2 selected, clearing the alarm signal will not reset the alarm memory for
the particular zones which triggered the given alarm. The signaling will be cleared after
reviewing the alarm log (press and hold down the key 5) or after arming the system.
With the option 3 activated, occurrence of a trouble in the system is indicated in the
keypad by means of the [
TROUBLE
] LED, as well as audibly, until the trouble cause is
removed. Viewing the current trouble, unless the trouble cause has been cleared, will only
mute the signaling (the LED keeps on blinking until the trouble is cleared, or a new review
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-5 in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-5

Satel CA-5 User Manual - English - 24 pages

Satel CA-5 Quick start guide - English - 12 pages

Satel CA-5 Installation Guide - English - 27 pages

Satel CA-5 Additional guide - German - 20 pages

Satel CA-5 User Manual - German - 24 pages

Satel CA-5 Installation Guide - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info