699583
10
Zoom out
Zoom in
Previous page
1/24
Next page
U
SER
M
ANUAL
CA-5
8
the panel is not ready to arm the system – which is signaled by the panel with three long
beeps (see description in the previous paragraph of this manual);
the function is disabled by the installer – this situation will be signaled with two long beeps.
4.9 D
ISARMING AND ALARM CLEARING
[CODE][#]
If the panel is armed (the [ARMED] LED is on or blinking) and/or it signals an alarm (the
[ALARM] LED is on or blinking), entering the user access code and confirming it with the
[#] or [
*
] key will disarm the system and clear the alarm. If, while entering the access code,
you make a mistake, press the [
*
] key and re-enter the code. The control panel will confirm
acceptance of the command by four short beeps and a long one, and by extinguishing the
[ARMED] LED and/or [ALARM] LED (if it was on).
The service code can only clear the tamper alarm or the keyboard alarm when the
[ARMED] LED is off (the control panel is disarmed).
The panel will not disarm the system or clear the alarm when the access code is wrong.
The user access code No. 5 will not clear the alarm in the armed mode if a special operating
mode has been selected for it by the installer, and the system was armed by another user.
Refusal to clear the alarm is signaled with three long beeps.
4.10 R
EMOTE ARMING
/
DISARMING AND CLEARING ALARM
The installer may install in the security system a radio controller to make remote control
possible, or a special button, designed for quick arming/disarming of the system or clearing of
alarm. For this purpose, one of the control panel programmable zones is used. The system
will be always armed in this mode (by violation of the zone), irrespective of the status
(violation) of the other zones of the control panel.
Arming/disarming is signaled in the keypad by 4 short beeps and 1 long beep.
The installer may restrict the zone operation to arming only, while disarming and alarm
clearing will require the user access code.
To facilitate remote control of the panel, the installer may activate the signaling of
arming/disarming on the OUT1 alarm output (see: Events Signaled on the OUT1 Output).
5. „HOLD
DOWN”
USER FUNCTIONS
The functions are available to every user of the protected site (without using the access
code). They are activated by holding down the function key until audible signal sounds in
the keypad. The first three functions refer to viewing the alarms and troubles. Depending on
the keypad type the viewing is done in different ways.
LCD keypad
To start the viewing, call the function and press any of the arrow keys - information on
the most recent alarm condition, referring to selected function, will be displayed. The
([
S
], [
T
]) arrow keys on the right side of the keypad allow the user to scroll through the
list of events provided by the alarm control panel. The events are displayed
chronologically ([
S
] – earlier ones, [
T
] – later ones).
The ([
W
], [
X
]) arrow keys on the left side of the keypad make it possible to display the
user or zone name (default one or entered into the control panel memory by the installer
using the DLOAD10 computer program). Pressing the same key again will restore the
previous mode of event information display.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-5 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-5 Plus in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-5 Plus

Satel CA-5 Plus Additional guide - English - 20 pages

Satel CA-5 Plus Installation Guide - English - 27 pages

Satel CA-5 Plus User Manual - German - 24 pages

Satel CA-5 Plus Additional guide - German - 20 pages

Satel CA-5 Plus User Manual - German - 24 pages

Satel CA-5 Plus Installation Guide - German - 28 pages

Satel CA-5 Plus User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info