699890
4
Zoom out
Zoom in
Previous page
1/4
Next page
4 ASP-100 SATEL
4. Installation and start-up
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly.
Be particularly careful during installation and replacement of the battery. The
manufacturer is not liable for the consequences of incorrect installation of the battery.
The siren must be installed on the wall, high above the floor, at a hard to access location, so as to
minimize the risk of tampering. Make sure that some free space is left above the siren (at least 2.5
cm). Otherwise, it will be impossible to replace the cover.
1. Remove the cover locking screws.
2. Lift up the enclosure cover by approx. 60º and remove it (see Fig. 3).
3. Connect the battery and add the siren to the wireless system (see the ACU-120 / ACU-270
controller manual or installer manuals for VERSA / VERSA IP / VERSA Plus control panels). The
sticker with serial number which shall be entered when registering the siren in the system can be
found on the electronics board.
4. Replace the siren cover.
5. Place the siren in the location intended for its installation.
6. Check the level of signal received from the siren by the ACU-120 / ACU-270 controller. If the
signal level is lower than 40%, select another place for installation. Sometimes, it is sufficient to
shift the device ten or twenty centimeters to obtain a considerable improvement in the signal
quality.
7. Remove the siren cover.
8. Disconnect the battery.
9. Move aside the catches holding the electronics module and remove it.
10. Place the enclosure base on the wall and mark the location of mounting holes (see Fig. 2). Be
sure to take into account the tamper mounting hole.
11. Drill the holes for wall plugs (screw anchors).
12. Secure the enclosure base to the wall with wall plugs (screw anchors) and screws. Remember
about the tamper mounting hole. The wall plugs (screw anchors) and screws delivered with the
siren are intended for brick, concrete and similar mounting surfaces. For other surfaces (e.g.
drywall, wood, styrofoam), use other wall plugs (screw anchors), as required.
13. Secure the electronics module in the enclosure base.
14. Connect the battery.
15. Replace the siren cover and fasten it with screws.
16. Configure the siren (set the signaling duration, type of acoustic signaling, etc.). For detailed
information on this subject, refer to the controller manual.
5. Battery replacement
The used batteries must not be discarded, but should be disposed of in accordance
with the existing rules for environment protection.
1. Start the service mode in the control panel.
2. After the leftmost LED on the siren starts blinking every 3 seconds, you can open the siren
enclosure.
3. Disconnect the battery.
4. Remove the battery cover (grasp the upper part of the cover with your fingers and pull it down).
5. Remove the old battery and place the new one in the battery cover.
6. Install the battery cover in the siren enclosure.
7. Press and hold down the tamper switch.
8. Connect the new battery.
9. When the leftmost LED on the siren starts blinking every second, release the tamper switch.
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. + 48 58 320 94 00
www.satel.eu
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel ASP-105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel ASP-105 in the language / languages: Dutch as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel ASP-105

Satel ASP-105 User Manual - English - 4 pages

Satel ASP-105 User Manual - German - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info