699870
3
Zoom out
Zoom in
Previous page
1/4
Next page
SATEL ARF-100 3
press the button to toggle between simulation of the device powered from an
external source and simulation of the device powered from a battery. After switch-
on the tester simulates operation of the device powered from an external source.
Which power supply method is being simulated is indicated by the LED .
Press and hold down the button to change the refresh rate of the radio signal level
indicator . After switching the tester on, the indicator refresh takes place during
polling and is signaled by one short beep. If you hold down the button longer than
3 seconds, the tester will enter and remain in the dense polling mode until the
button is released. When in this mode, the indicator is refreshed every 2 seconds,
which is signaled by two short beeps.
radio signal level indicator. The indicator consists of 7 LEDs (2 yellow and 5 green ones),
which present percentage of the radio signal level (15 – 100%). Intensity of the LED
lighting depends on which device is simulated by the tester. If a battery-powered device
is being simulated, the LED light is weaker. If, when the LEDs are ON, you change the
power supply method (by pressing the button), the LEDs will go off. They will only go
on again during the next polling and will show an updated radio signal level. If the tester
battery is low, all the indicator LEDs are blinking.
red LED indicating the tester operating mode:
ON checking the level of radio signal received by the tester from the ABAX
controller / control panel,
flashing checking the level of radio signal received by the ABAX controller / control
panel from the tester.
red LED indicating how the device being simulated is power supplied:
ON powered from battery (e.g. AMD-100, AMD-101 and APD-100 detectors,
ASP-205 siren),
OFF powered from an external source (e.g. ACX-200 expander, ASP-105 siren,
ASW-100 wireless controller).
4. Start-up and testing the radio signal level
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly.
Be particularly careful during installation and replacement of the battery. The
manufacturer is not liable for the consequences of incorrect installation of the
battery.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
1. Install the battery and switch the tester on.
2. Add the tester to the wireless system (see the manual for ACU-120 / ACU-270 controller
or the installer manual for INTEGRA 128-WRL / VERSA / VERSA Plus / VERSA IP
control panel). The serial number of each tester is 0000500.
3. Use the button to define how the device simulated by the tester is supplied.
4. Start the test mode on the ABAX controller / control panel.
5. Place the tester in the location intended for installation of wireless device and check the
level of radio signal received by the tester from the ABAX controller / control panel and
the level of signal received by the ABAX controller / control panel from the tester. If the
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel ARF-100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel ARF-100 in the language / languages: English as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel ARF-100

Satel ARF-100 User Manual - German - 4 pages

Satel ARF-100 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info