699609
5
Zoom out
Zoom in
Previous page
1/5
Next page
SATEL ACX-210 3
precision pliers,
double-sided mounting tape.
1. Connect the temporary power supply (4...24 V DC) to the expander.
2. Add the expander to the wireless system (see the ABAX 2 / ABAX controller manual or
the INTEGRA 128-WRL control panel installer manual). The sticker with serial number
which shall be entered when registering the expander in the system can be found on the
device enclosure.
In the INTEGRA / VERSA alarm system, the expander is identified as ACX-200.
Simultaneous operation of the expander by the ABAX 2 and ABAX controller /
INTEGRA 128-WRL alarm control panel is not possible.
3. If the expander is to be installed in the enclosure of another device (e.g. a detector), put
the expander into that enclosure.
4. Place the expander / device in the enclosure of which the expander is mounted at the
location where it is to be installed.
5. Check the level of signal received from the expander by the ABAX 2 / ABAX controller or
the INTEGRA 128-WRL control panel. If the signal level is lower than 40%, select
another place for installation. Sometimes, it is sufficient to shift the device ten or twenty
centimeters to obtain a considerable improvement in the signal quality. You can also try
to turn the expander around to check what effect the change in antenna position will have
on the signal strength level.
The ARF-200 tester makes it possible to check the radio signal strength at the place of
future installation without having to put the expander there.
6. Disconnect the temporary power supply.
7. If the expander is to be mounted inside another device enclosure, run a bunch of wires
into the enclosure so as to make connections referred to in steps 8 to 10.
8. Connect detectors to the expander zones. For the EOL configuration, use a 2.2 k
resistor, and for the 2EOL configuration – two 1.1 k resistors.
9. Connect the devices to the expander outputs.
Given the specific character of radio communication, it is not recommended that the
expander be used in applications where quick switchover of the output status is
expected.
10. Connect the power leads to the +12V and COM terminals (use flexible conductors with a
cross-section of 0.5-0.75 mm
2
).
Do not use the battery to power the expander.
11. Fasten the expander to the mounting surface or, if it is to be installed in the enclosure of
another device, put the expander inside that enclosure. To install the expander, you can
use a double-sided mounting tape.
12. Power up the expander.
13. Configure the expander settings (refer to ABAX 2 / ABAX controller manual or INTEGRA
/ VERSA series control panels programming manual).
Taking into account the requirements of EN50131-3 standard, enter 400 ms when
configuring the sensitivity of alarm zones.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel ACX-210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel ACX-210 in the language / languages: English as an attachment in your email.

The manual is 0,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel ACX-210

Satel ACX-210 Quick start guide - English - 2 pages

Satel ACX-210 User Manual - German - 6 pages

Satel ACX-210 Quick start guide - German - 2 pages

Satel ACX-210 User Manual - Dutch - 6 pages

Satel ACX-210 Quick start guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info