783736
15
Zoom out
Zoom in
Previous page
1/18
Next page
Digitaler Thermostat SF-283F
Merkmale der Funktion
Es handelt sich um einen intelligenten Temperatur Regler, der auf
den Kompressor bis 1 HP anwendbar ist.
Temperaturanzeige / Temperatursteuerung / Abtauung durch
Ausschalten des Kompressors / Licht Steuerung / Lüftersteuerung
/ Hoch-, Tieftemperaturalarm / Wertespeicherung / Selbsttest /
Parametersperre.
Spezifikationen
1. Stromversorgung: 220VAC
2. Temperaturfühler: NTC, ein Sensor, 3,5 Meter lang, weder
positiv noch negativ
3. Anzeigebereich der Temperatur: -45120℃. Genauigkeit:
±1℃.
4. Bereich der eingestellten Temperatur: E1 ~ E2. Standard
Einstellung: 03℃.
5. Abmessungen: 178 (Länge) × 31 (Breite) × 34 (Tiefe) mm.
Abmessung der Montageöffnung: 172 (Länge) × 26 (Breite) mm.
6. Temperatur der Umgebung: -10 +60 ℃. Relative
Luftfeuchtigkeit: 20%~90% (nicht kondensierend)
7. Kontaktkapazität des Relaisausgangs
Kompressor: N. O. 30A/250VAC
(gilt für 1PS-Kompressor, wenn Kompressor mehr als 1 PS hat,
braucht man einen AC-Schutz)
Verdampfer Lüfter: N.O. 10A/250VAC. Licht: N.O.
10A/250VAC Glasscheibenheizung: N.O. 10A/250VAC: N.A.
10A/250VAC
Bedienung
1. Einstellung der Solltemperatur (Kompressor-Stopptemperatur).
- Drücken Sie die Taste "SET", die eingestellte Temperatur wird
angezeigt.
- Drücken Sie die Taste oder ▼, um den Temperaturwert zu
ändern und zu speichern. Drücken Sie die "SET"-Taste, um die
Einstellung zu beenden und die Kühlraumtemperatur anzuzeigen.
Wenn innerhalb von 6 Sekunden keine Taste mehr gedrückt wird,
wird die Kühlraumtemperatur angezeigt (eingestellter
Temperatur-Einstellbereich: Parameter E1E2).
2. Ein-/Ausschalten: Drücken Sie die Taste 3 Sekunden lang,
um den Kühlmodus und die Temperaturanzeige auszuschalten, "-
--" wird angezeigt, und alle Prozesse werden gestoppt (mit
Ausnahme der Beleuchtung). Drücken Sie die Taste erneut einmal,
die gemessene Temperatur wird angezeigt, der Kühlbetrieb wird
nach einer Verzögerungszeit gestartet.
3. Kühlung LED: Während der Kühlung leuchtet die LED; wenn
die Kühlraumtemperatur konstant ist, ist die LED aus; während
des Verzögerungsvorgangs blinkt die LED.
4. LED Abtauung: Während der Abtauung leuchtet die LED; wenn
die Abtauung beendet ist, ist die LED aus.
5. Glasscheibenheizung LED: Während des Abtauens leuchtet die
Glasscheibenheizung LED; beim Verlassen des Abtauvorgangs ist
die LED aus.
6. Beleuchtung-LED: Wenn die Beleuchtung angeschlossen ist, ist
Beleuchtung LED an. Wenn die Beleuchtung ausgeschaltet ist,
geht die LED wieder aus.
Model: SF-283F Digital Temperature
Controller
Features of Function
It is an intelligent controller and applicable to the
compressor Include 1HP
Temperature Display / Temperature Control / Defrost by
turning off comp.Light control / Fan control / High, low
temperature alarm/ Value Storing/Self Testing /Parameter
Locking.
Specifications
1. Power supply input: 220VAC
2. Temperature sensor: NTC, one sensor, 3.5 meters long,
neither positive nor negative
3. Range of temperature display: 45120℃. Accuracy:
±1℃.
4. Range of set temperature: E1~E2. Factory default: 03℃.
5. Dimension: 178 (Length) × 31 (Width) × 34 (Depth) mm.
Mounting hole dimension: 172 (Length) × 26 (Width) mm.
6. Temperature of the operating environment: -10 60 ℃.
Relative Humidity: 20%~90% (Non-condensing)
7. Relay output contact capacity
Compressor: N. O. 30A/250VAC
(applicable to one HP Compressor, if more it needs to
connect an AC contactor)
Evap. Fan: N. O. 10A/250VAC. Light: N.O. 10A/250VAC
Defog: N.O. 10A/250VAC
Front Panel Operation
1. Set temperature (compressor stop temperature)
adjustment.
Press “SET” button, the set temperature is displayed.
Press or button to modify and store the displayed
value. Press SET” button to exit the adjustment and display
the cold-room temperature. If no more button is pressed
within 6 seconds, the cold-room temperature will be
displayed (set temperature adjustment range: parameter E1
E2).
2. Power ON / OFF: Press button for 3 seconds to turn
off refrigeration work mode and temperature display, “---”
will be displayed, and all the control outputs will be stopped
(except for the light). Press button again for once, the
measured temperature will be displayed, refrigeration work
mode will be started after delay time.
3. Refrigerating LED: During refrigeration, the LED is on;
when the cold room temp. is constant, the LED is off; during
the delay process, the LED flashes.
4. Defrost LED: during defrosting, the LED is on; when it
exit defrost, the LED is off.
5. Defog LED: during defog, the defog LED is on; when it
exit defog, the LED is off.
6. Light LED: when it connects the light, the light LED is
on. When it disconnects the light, the LED is off.
7. Manual start/stop defrost: Press button and hold for 6
seconds to defrost or stop defrost
8. Light: Press button, the light is connected. Press the
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Saro GTK1530 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Saro GTK1530 in the language / languages: English, German as an attachment in your email.

The manual is 1.78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info