68243
147
Zoom out
Zoom in
Previous page
1/166
Next page
VPC-E10EX
VPC-E10
VPC-E10GX
INSTRUCTION MANUAL
Digital Camera
Please read these instructions carefully before using the camera.
Make sure to read and understand the separate booklet “
SAFETY MANUAL”.
Keep this manual in a safe place for later reference.
Important note
This manual explains how to safely operate the VPC-E10EX, VPC-E10 and
VPC-E10GX.
Any information regarding only one of these products will be labeled as such.
i English
Warning
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
kFOR AMERICAN USERS
The following advisory is included in accordance with the laws of the State of
California (USA):
WARNING:
This product contains chemicals, including lead, known to the State of
California to cause cancer, birth defects or other reproductive harm. Wash
hands after handling.
i This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
h Reorient or relocate the receiving antenna.
h Increase the separation between the equipment and receiver.
h Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
h Consult the dealer or an experienced radio/TV technician for help.
i Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Declaration of Conformity
Model number: VPC-E10
Trade Name: SANYO
Responsible party: SANYO FISHER COMPANY
Address: 21605 Plummer Street, Chatsworth, California 91311
Telephone No.: (818) 998-7322
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
English ii
kFOR CANADIAN USERS
i This Class B digital apparatus complies with Canadian ICES-003.
kFOR EU USERS
Note:
iThis symbol mark and recycle system apply only to EU
countries and do not apply to countries in other areas of
the world.
Your SANYO product is designed and manufactured with
high quality materials and components which can be
recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed of
separately from your household waste.
Please dispose of this equipment at your local community
waste collection/recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
FOR RUSSIAN USERS
This product certified by official certification company
which is authorized by Russian Federation.
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 München, Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534, Japan
iii English
kSymbols used in this manual
HINT Points giving some extended instructions or special points to pay
attention to.
CAUTION Points that require special attention.
(page xx) Refer to the page indicated for detailed information.
You may find the answers to questions or problems concerning camera
operation in the sections “COMMONLY ASKED QUESTIONS” (page 130)
and “TROUBLESHOOTING” (page 136).
English iv
SHOOT, PLAY BACK AND SAVE
Install the battery pack
1 Use the supplied charger to charge the battery pack.
h The CHARGE indicator is lit during charging.
h The CHARGE indicator will turn off when the battery pack is fully charged.
h Charging takes approximately 2 hr. 30 min.
2 Open the battery/card compartment cover, and insert the battery pack.
h The battery/card compartment cover is located on the bottom of the
camera.
h Press the ON/OFF button to turn the camera on.
CHARGE indicator
Battery pack
To power outlet
[o] mark
Battery pack charger
[o] mark ON/OFF button
v English
SHOOT, PLAY BACK AND SAVE
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i Sanyo declines any claim for compensation for recorded contents etc. in
case of photographing or recording failure due to a chance camera or card
flaw.
Shooting
1 Press the [m] button.
h The shooting mode menu
appears.
2 Press the [l] or [m] button to
select the shooting mode.
3 Press the SET button.
h The shooting mode is
indicated by an icon in the
upper left area of the monitor.
4 Press the shutter button.
Single-shot mode:
A still image is captured.
Sequential shots mode:
Shooting begins. Release the
shutter button to discontinue
shooting.
Video clip recording mode:
Recording begins. To stop
recording, press the shutter
button again.
Shutter button
[l] / [m] buttons
6
s:
Single-shot mode
O:
Sequential shots mode
X:
Video clip recording mode
<Shooting mode>
PHOTOGRAPH 1 IMAGE
Single-shot
Video clip recording
Sequential shots
English vi
Playback
kStill image playback
1 Press the playback button [=].
h The display switches to the
Playback Screen.
h To view other images, press the
[l] or [m] button.
h If the playback button [=] is
pressed, the display returns to
the Shooting Screen.
kVideo clip playback
1 Press the playback button [=].
h The display switches to the
Playback Screen.
h Press the [l] or [m] button to
display the video clip you wish to
play back.
h Video clips are indicated by a
video clip pattern along the top
and bottom of the screen.
2 Press the SET button.
h Playback of the selected video
clip begins.
h If the playback button [=] is
pressed again, the display
changes to the Shooting Screen.
When you are finished taking pictures...
Press the ON/OFF button to turn the camera off.
PLAY
ON/OFF button
Video clip pattern
[l] / [m] buttons
<Video Clip Playback
Screen>
Playback button
[=]
vii English
SHOOT, PLAY BACK AND SAVE
Save the photographed image data to your
computer (Windows XP)
The Adobe Photoshop Album Starter Edition (in this manual referred to
as Photoshop Album SE) program in the supplied SANYO Software
Pack lets you easily copy the data from your camera to your computer.
Install Photoshop Album SE
1 Set the supplied CD-ROM (SANYO Software Pack) in your
computer’s CD-ROM drive.
h The installation window opens.
2 Click on the application program you wish to install.
h After clicking on an application program, follow the instructions shown
on the monitor to install the program.
h When the installation is complete, the product registration window will
appear, but click on the Exit button to close the window.
3 In the installation window, click on [Finish].
h The installation window closes.
h Remove the CD-ROM from your computer’s CD-ROM drive.
<About the Kodak online service>
h When the installation window closes, a dialog box to connect to the
website introducing Kodak’s online service appears. Check the [No
thanks !] option button, and then click on the [OK] button.
Install Photoshop Album SE.
English viii
Copy data from your camera to the computer
Connect your camera to a computer, and copy the desired data to the
computer.
1 Turn on the computer, and use the supplied dedicated USB interface
cable to connect your camera to the computer.
h Connect the cable between the camera’s USB/AV terminal and the
computer’s USB connector.
2 Turn on the camera (page 23).
h The USB Connection Screen appears on the camera’s monitor.
SELECTOK
USB CONNECTION
CANCEL
PRINTER
COMPUTER
To USB connector
on the computer
Supplied dedicated USB
interface cable
To the USB/AV terminal
ix English
SHOOT, PLAY BACK AND SAVE
3 Select “COMPUTER”, and press the
SET button.
h The screen to select the connection
mode appears.
4 Select “CARD READER”, and press the SET button.
h The screen to import data to the computer appears on your
computer’s monitor.
5 Click the [IMPORT] button.
h Copy the camera data to the following folder:
My Pictures\Adobe\Digital Camera\Date folder
h When the data has been successfully copied, a dialog box appears to
confirm whether or not you wish to delete the original data from the
camera.
6 Click the [YES] button if you wish to delete the data from the
camera’s memory, or [NO] if you do not wish to delete it.
h The Photoshop Album SE catalogue screen appears.
h The data you copied appears on the computer monitor. Confirm that
the desired data was correctly copied. If it was not copied, from the
[Import] menu select [From camera, mobile phone or card reader],
and copy the desired data.
USB CONNECTIONUSB CONNECTION
CARD READER
SCREEN CAPTURE
PC CAMERA
MTP
OKOK
SELECTSELECT
English x
7 Click the close button.
h Photoshop Album SE closes.
About video clip files recorded with this camera
h You can use Apple’s QuickTime 3 or later version to play back video
clips on a computer.
h QuickTime can be downloaded from the following website:
http://www.apple.com/quicktime
1 English
CONTENTS
CONTENTS ........................................................................................... 1
QUICK SEARCH BY OPERATION ........................................................ 3
CHECKING THE INCLUDED ACCESSORIES ...................................... 8
GETTING THE MOST OUT OF YOUR CAMERA ............................... 11
SYSTEM MAP ..................................................................................... 14
SETUP
PARTS NAMES ................................................................................... 15
CHARGING THE BATTERY PACK ..................................................... 17
INSTALL THE BATTERY PACK AND CARD ...................................... 21
TURNING THE CAMERA ON AND OFF ............................................. 23
DATE AND TIME SETTING ................................................................. 25
BASIC OPERATION
BEFORE TAKING PICTURES ............................................................. 28
CAPTURING AND PLAYING BACK STILL IMAGES .......................... 37
SHOOTING SEQUENTIAL SHOTS ..................................................... 47
VIDEO CLIP RECORDING AND PLAYBACK ..................................... 49
USING THE SCENE FUNCTION ......................................................... 53
USING THE ZOOM .............................................................................. 58
FLASH SETTING ................................................................................. 59
SELF-TIMER ........................................................................................ 61
FOCUS RANGE ................................................................................... 63
SHOOTING
ACCESSING THE RECORDING MENU ............................................. 66
TOUCH SENSOR (TOUCH FOCUS) SETTING .................................. 69
RESOLUTION/VIDEO SIZE SETTING ................................................ 70
COMPRESSION RATE SETTING ....................................................... 73
FOCUS AREA SETTING ..................................................................... 74
LIGHT-MEASURING MODE SETTING ............................................... 76
ISO SENSITIVITY ................................................................................ 77
WHITE BALANCE ................................................................................ 79
EXPOSURE CORRECTION ................................................................ 80
DATE IMPRINT .................................................................................... 81
English 2
PLAYBACK
DISPLAYING THE PLAYBACK MENU ................................................82
IMAGE PROTECT ................................................................................84
ROTATE IMAGE ...................................................................................85
CHANGING IMAGE SIZE (RESIZE) ....................................................86
BLUR CORRECTION ...........................................................................87
CONTRAST CORRECTION .................................................................89
RED-EYE CORRECTION .....................................................................91
COPY DATA .........................................................................................93
PRINT SETTINGS ................................................................................95
SLIDESHOW PLAYBACK ..................................................................100
DISPLAYING IMAGE PROPERTIES (INFORMATION SCREEN) .....101
OPTION
DISPLAYING THE OPTION MENU ....................................................102
SOUNDS ............................................................................................105
POST-VIEW SETTING .......................................................................107
SCREEN LANGUAGE ........................................................................108
TV SYSTEM SETTING .......................................................................109
AUTO POWER OFF FUNCTION .......................................................110
FILE NO. MEMORY ............................................................................111
INITIALIZING THE CARD MEMORY AND INTERNAL MEMORY .....114
RESETTING THE CAMERA SETTINGS ............................................116
CHECKING THE REMAINING INTERNAL MEMORY AND CARD
MEMORY .......................................................................................117
CHECKING THE REMAINING BATTERY CHARGE .........................119
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A TV .....................................................................121
DIRECT PRINTING ............................................................................122
APPENDICES
COMMONLY ASKED QUESTIONS ...................................................130
TROUBLESHOOTING ........................................................................136
SPECIFICATIONS ..............................................................................142
HINTS FOR TAKING PICTURES .......................................................151
3 English
QUICK SEARCH BY OPERATION
Your camera has an abundance of convenient features and functions. From
creating precisely the photo you want, to viewing images using various
techniques, you can locate the exact operation for your purposes in the
following table.
Shooting/recording
Basic operation Convenient functions Additional functions
Getting started
shooting
“Recording a video clip
on page 49
“Shooting single shots”
on page 37
•“SHOOTING
SEQUENTIAL SHOTS”
on page 47
Change the setting to
sequential shots
“How to use the best shot
feature” on page 56
Log the date and time
of your photos
“DATE AND TIME
SETTING” on page 25
“DATE IMPRINT” on
page 81
Zoom in on the
subject
“USING THE ZOOM” on
page 58
Close-up
photography
“FOCUS RANGE”
(macro mode) on
page 63
For more accurate
focus
“FOCUS RANGE”
(manual focus) on
page 63
Set the focus to a
narrow range
“FOCUS AREA
SETTING” on page 74
Check the focus
status
“Zoom jump playback” on
page 44
Optimize the photo quality
“RESOLUTION/VIDEO SIZE SETTING” on page 70
Capture fast-moving subjects
“USING THE SCENE FUNCTION” (sports mode) on page 53
English 4
Shooting/recording
Basic operation Convenient functions Additional functions
Shoot in dark conditions
“EXPOSURE CORRECTION” on page 80
“FLASH SETTING” on page 59
“USING THE SCENE FUNCTION” (night view portrait mode/fireworks mode/lamp
mode) on page 53
Increase the camera’s sensitivity
“ISO SENSITIVITY” on page 77
Photographing people
“USING THE SCENE FUNCTION” (portrait mode/night view portrait mode/cosmetic
mode/face chaser mode) on page 53
“How to use the face chaser feature” on page 57
“FLASH SETTING” (red-eye reduction) on page 59
Photographing landscapes
“USING THE SCENE FUNCTION” (landscape mode) on page 53
Take a self-photo
“SELF-TIMER” on page 61
Make images lighter
or darker
“EXPOSURE
CORRECTION” on
page 80
Measure the
brightness of a
specific area
“LIGHT-MEASURING
MODE SETTING” on
page 76
Adjust the camera’s
sensitivity
“ISO SENSITIVITY” on
page 77
Change the color of
the images
“USING THE SCENE
FUNCTION”
(monochrome mode/
sepia mode) on page 53
Make white appear
natural
“WHITE BALANCE” on
page 79
5 English
QUICK SEARCH BY OPERATION
Playback
Basic operation Convenient functions Additional functions
Getting started
viewing images
“Playing back the video
clip” on page 50
Adjust the playback volume
“SOUNDS” on page 105
“Viewing still images” on
page 39
Search for image data
“9-image display
playback” on page 40
“Folder playback” on
page 42
“Quick scroll playback”
on page 41
Magnify an image
“Magnifying (zooming in)
the image” on page 43
Check the focus
status
“Zoom jump playback” on
page 44
Change the
orientation
•“ROTATE IMAGE on
page 85
Slideshow playback
“SLIDESHOW PLAYBACK” on page 100
Adjust the monitor brightness
“Adjust the monitor brightness” on page 35
Playback on a TV
“CONNECTING TO A TV” (for playback) on page 121
Set the TV system
“TV SYSTEM SETTING”
on page 109
English 6
Data managing/processing
Basic operation Convenient functions Additional functions
Edit photos
“BLUR CORRECTION” on page 87
“CONTRAST CORRECTION” on page 89
“RED-EYE CORRECTION” on page 91
Copy files from the internal memory to the card, or vice versa
“COPY DATA” on page 93
Delete files
“Deleting files” on
page 45
Protect images from accidental erasure
“IMAGE PROTECT” on page 84
Format a card
“INITIALIZING THE CARD MEMORY AND INTERNAL
MEMORY” on page 114
Specify the number of prints and date imprint
“PRINT SETTINGS” on page 95
View the settings that were in effect when the image/audio data was
recorded
“DISPLAYING IMAGE PROPERTIES (INFORMATION SCREEN)” on page 101
7 English
QUICK SEARCH BY OPERATION
Using with a computer
Basic operation Convenient functions Additional functions
Use the camera as a card reader
“BEFORE MOUNTING YOUR CAMERA” on page 6 in the SANYO Software Pack
INSTRUCTION MANUAL
“MOUNTING AND DISMOUNTING YOUR CAMERA” on page 9 in the SANYO
Software Pack INSTRUCTION MANUAL
Copy files from your
camera to a computer
“Copy data from your
camera to the computer”
on page viii
Using with Windows Vista
“CONNECTING IN THE MTP MODE” on page 14 in the
SANYO Software Pack INSTRUCTION MANUAL
Playback
“About video clip files recorded with this camera” on page 8 in the SANYO Software
Pack INSTRUCTION MANUAL
Using as a webcam
“USING AS A PC CAMERA” on page 16 in the SANYO Software Pack INSTRUCTION
MANUAL
Record an image of the computer screen
“SCREEN CAPTURE” on page 23 in the SANYO Software Pack INSTRUCTION
MANUAL
English 8
CHECKING THE INCLUDED ACCESSORIES
i Handstrap: 1 i SANYO Software Pack
(CD-ROM): 1
i Lithium-ion battery pack
(battery pack): 1
i Lithium-ion battery pack
charger and power cord
i Dedicated USB interface cable:
1
i Dedicated AV interface
cable: 1
i “SAFETY MANUAL
(safety precautions booklet)
Please read this booklet
carefully before using the
digital camera.
i Quick Guide
9 English
CHECKING THE INCLUDED ACCESSORIES
Attaching the handstrap
English 10
Media cards that can be used with this camera
The types of card that can be inserted into and used with this camera are:
i SD Memory Card
i SDHC Memory Card
What “card” means in this manual
i In this manual, SD Memory Cards and SDHC Memory Cards that can be
used in this digital camera are referred to as “card”.
11 English
GETTING THE MOST OUT OF YOUR CAMERA
It’s loaded with lots of functions that are possible only in a digital camera,
including a super-quick focus, an easy-to-understand guidance display on a
large screen, a more extensive scene function, and more.
You’ll never miss a photo opportunity, thanks to
the quick focus: Touch focus (page 69)
Just touch the shutter button lightly, and the touch sensor automatically
focuses the image (touch focus).
F5.2
1/102
English 12
k Abundant scene functions (page 53)
You can select from a variety of preset settings (aperture, shutter speed, etc.)
for specific shooting conditions.
k Photo correction feature (page 87)
Your camera can correct some problems in still images–red eyes resulting
when the flash is used (red-eye effect) and blurred images due to camera
movement (camera shake)–to produce more natural-looking photos. In
addition, hazy images can be enhanced to show sharper outlines (contrast
correction).
AUTO
AUTO
AUTO
Use auto settings
Use auto settings
Use auto settings
13 English
GETTING THE MOST OUT OF YOUR CAMERA
k Date/time stamp feature (page 81)
Use the “date stamp feature” to print the capture date and time on your photo,
even if your printer does not have a date stamp function.
2008.12.24
English 14
SYSTEM MAP
The included accessories can be used to connect your camera to a computer,
printer or TV. By connecting the camera to your computer, you can, for
example, copy your photos to the computer’s hard disk. You can connect it to
a printer for direct printing of your photos. Or take the card to a photo shop to
have your photos printed there.
Dedicated
USB interface
cable
Dedicated AV
interface cable
Computer
Printer
TV
Commercially available
SD Memory Card/
SDHC Memory Card
Internet
i Card reader
i DPOF-compatible
printer
i Photo shop
Battery charger
(supplied)
15 English
SETUP
PARTS NAMES
Front
Lens
Self-timer indicator
Battery/card compartment cover
Flash
ON/OFF button
Shutter button
Speaker
Tripod stand hole
Bottom
Microphone
English 16
Rear
Zoom switch
Monitor
SET button
Playback button [=]
[n] button
[o] button
[l] button
[m] button
Strap holder
SCENE button
MENU button
USB/AV terminal cover
17 English
CHARGING THE BATTERY PACK
Please charge the supplied battery pack before using it.
1 Connect the supplied power
cord to the socket on the
battery pack charger.
h Insert the connector straight
and securely.
2 Insert the battery pack in the
battery charger.
h Insert it in the direction
indicated by the [o] mark
on the battery pack.
3 Plug the power plug into a
power outlet (AC 100 V to
240 V).
h Charging begins.
h The CHARGE indicator is lit
during charging.
4 When the CHARGE indicator
turns off, unplug the power
cord from the power outlet,
and remove the battery pack
from the charger.
HINT
i Charging takes approximately 2 hr. 30 min.
Battery pack
[o] mark
To power outlet
Battery pack charger
Power cord
CHARGE indicator
Battery pack charger
English 18
Charging the battery pack
Be sure to fully charge the supplied or separately sold battery pack before
using it in your camera. For charging the battery pack, use the supplied
charger.
Charge the battery pack if it is being used for the first time, and recharge it
whenever the remaining charge is low (see “CHECKING THE REMAINING
BATTERY CHARGE” on page 119).
Does the battery pack feel hot?
i During charging, the charger and battery pack will be warm. This is normal
and does not indicate a malfunction.
If there is interference to your TV or radio during charging...
i Move the battery pack and charger further away from the TV or radio.
Ambient temperature during charging
i It is recommended that the ambient temperature during charging be
between about 10°C and 35°C (50°F and 95°F). Due to the characteristics
of the battery pack, at temperatures below 0°C (32°F), it may not be
possible to sufficiently charge it.
i When the battery pack temperature is high, the safety function may be
activated and halt charging.
Charge a battery pack in the following cases
i A battery pack which has not been used for a long time
i Newly purchased battery pack
FOR AMERICAN USERS:
i Use a UL Listed, 1.8-3m (6-10ft), Type SPT-2 or NiSPT-2, AWG No.18
power supply cord, rated for 125V 7A, with a non-polarized NEMA 1-15P
plug rated for 125V 15A.
19 English
CHARGING THE BATTERY PACK
About the CHARGE indicator
The CHARGE indicator shows the status of the battery pack and the charger.
Please refer to the following table if the indicator flashes abnormally.
CAUTION
Do not charge the battery pack immediately after the camera has been
in continuous use for a long time
i The battery pack becomes hot when the camera is used continuously for a
long time. If you attempt to charge the battery pack in this state, the safety
function may be activated and it may not be possible to charge the battery
pack. Wait until the battery pack has cooled down before attempting to
charge it.
Does the battery pack appear swollen?
i The lithium-ion battery used in this camera may expand slightly when
stored in a hot environment or repeatedly used, but this is not a safety
hazard.
CHARGE indicator
Not lit Not connected properly
i To recharge the battery pack, the power cord of the
charger must be connected to a power outlet, and the
plug at the other end inserted in the charger’s power
socket (page 17).
i The battery pack is not installed, or it is not installed
correctly (page 17).
Charging finished
Lit Charging
Flashing Problem with the battery pack or battery pack charger
i Immediately remove the battery pack from the charger.
i Do not use an abnormal battery pack. (The usable life of
the battery pack has probably expired.)
English 20
HINT
About the internal backup battery
i This camera’s internal battery serves to maintain the date and time
settings, as well as the shooting settings. The backup battery will be fully
charged when the battery pack is kept in the camera continuously for about
2 days. In the fully charged state, the backup battery will maintain the
camera settings for about 7 days.
When not using the camera for a long time, remove the battery pack
i A small amount of power is still used even if the digital camera is turned off,
and it is therefore recommended that the battery pack be removed from the
camera if it is not going to be used for a long time. Note that when the
battery pack is removed for a long period, the time and date settings may
be cleared. Before using your camera again, be sure to confirm that the
camera settings are correct.
To prolong the life of the battery pack
i Although the battery pack is an expendable item, you can maximize the life
of the battery by heeding the following suggestions.
h Do not leave the battery under the hot summer sun or exposed to other
high-temperature environments.
h Do not continually recharge the battery when it is already fully charged.
After fully charging it once, for example, use it for a while to partially
discharge it before charging it again.
h When the battery is not to be used for a long time, if possible store the
partially charged (not fully charged) battery in a cool environment.
21 English
INSTALL THE BATTERY PACK AND CARD
Installation
i The card can be used after it has been formatted with the camera
(page 114).
i Make sure that the battery pack and card orientation are correct.
21
43
Open battery/card compartment cover
on the bottom of the camera.
Insert the battery pack.
Insert the card all the way until it
clicks.
3 Pull out
2 Push down
1 Open
[o] mark
2 Push
<Battery pack>
Close the battery/card compartment
cover.
* To remove...
<Card>
1 Open
3 Pull out
English 22
CAUTION
Be careful when removing the card
i Do not attempt to forcibly remove the card.
i Never remove the card when the camera is connected to a computer or
printer, or when the self-timer indicator is flashing quickly. In doing so, you
risk losing the data stored in the card.
Keep your finger on the card until it is completely inserted or released
i If you remove your finger too soon, the card may spring out and become
lost or hit someone in the eye.
HINT
Shooting without a card installed
i When a card is installed, images are recorded to and played back from the
card. When no card is installed, images are recorded to and played back
from the camera’s internal memory. When the camera is turned on with no
card installed, the internal memory icon is shown on the monitor to let
you know that the images you capture will be saved to the camera’s
internal memory.
Warning concerning battery pack temperature
i If the battery pack in the camera becomes too hot, a blinking temperature
warning icon \ will appear on the monitor. If the blinking icon does
appear, the camera should be turned off as soon as possible and the
battery pack allowed to cool before the camera is turned on again.
i Note that the camera will turn off automatically if it continues to be used
with the battery pack temperature elevated.
23 English
TURNING THE CAMERA ON AND OFF
Turning on the camera
In the shooting mode
1 Press the ON/OFF button.
h The camera turns on.
h The camera turns on in the
shooting mode that was active
before it was last turned off.
In the playback mode
1 Press the playback button [=] for
at least one second.
h The Playback Screen appears on
the monitor (pages 39 and 50).
Turning off the camera
1 Press the ON/OFF button.
h The camera turns off.
<If the camera was turned on by pressing the playback button [
=
]>
h When the playback button [=] or ON/OFF button is pressed, the
camera turns off.
Monitor
ON/OFF button
Playback button [=]
English 24
About the auto power off function
In order to preserve battery pack power when, for example, the camera has
accidentally been left on, the camera is furnished with an “auto power off
function by which the camera automatically turns off after a certain period of
inactivity (about 1 minute during shooting or about 3 minutes during playback
[factory default settings]).
i If the auto power save function has operated to turn the camera off, press
the ON/OFF button to turn it back on.
i You can change the setting for the time elapsed before the camera
automatically turns off (page 110).
i When the camera is connected to a computer or printer using the
dedicated USB interface cable, the auto power save function is disabled,
and the camera turns off after about 12 hours.
HINT
If the K icon appears...
i When a picture is taken, the date and time it was captured is recorded with
it. When the date and time cannot be recorded with the image because the
date and time have not yet been set (page 25), the K icon appears. To
have the date and time recorded with images, please make this setting
before capturing images.
25 English
DATE AND TIME SETTING
The camera will record the date and time an image is captured so that you
can display them during playback. Therefore, before capturing images, make
sure the correct date and time are set.
Example: To set the clock to 7:30 p.m. on December 24, 2008
1 Press the ON/OFF button to turn
the camera on, and press the
MENU button.
h The Recording Menu appears
(page 67).
2 Press the [o] button to select the
3 tab, and press the [m] button.
h The Option Menu appears
(page 103).
3 Press the [n] or [o] button to
select “CLOCK SET”, and press
the SET button or the [m] button.
h The Clock Set Screen appears.
h The current date and time
settings are shown.
h Follow the procedures below to
enable or disable the date display
during playback, to set the display
format for the date, and to set the
date and time.
h To return to the Option Menu,
press the MENU button.
10
M
1/2RECORDING MENU
TOUCH SENSOR
RESOLUTION
COMPRESSION
EXP MEASURE
FOCUS MODE
ISO
OK EXIT
NTSC
0
SOUND
CLOCK SET
OPTION MENU
POST VIEW
1sec
BRIGHTNESS
LANGUAGE
TV SYSTEM
1/2
OK EXIT
2008/03/01
12:00
OK
Y / M / D
DATE
TIME
DISP
CLOCK SET
3 tab
English 26
4 Set the date and time.
1 Press the [n] or [o] button to
change the year indication.
h You can press the [m] button to
select the indication you wish to
change.
h Repeat these steps to select the
month indication and day
indication, and set the date to
December 24, 2008.
2 Press the [m] button to select the
time indication.
3 Press the [n] or [o] button to
change the time setting.
4 Press the [m] button to select the
Y/M/D indication.
5 Press the [n] or [o] button to
change the displayed date order.
h Press the [o] button to change the displayed date order as follows:
h Press the [n] button to change it in the reverse order.
2008/12/24
19:30
OK
Y / M / D
CLOCK SET
DATE
TIME
DISP
2008/12/24
19:30
Y / M / D
OK
CLOCK SET
DATE
TIME
DISP
2008/12/24
12:00
OK
Y / M / D
CLOCK SET
DATE
TIME
DISP
Y / M / D M / D / Y D / M / Y DISP OFF
27 English
DATE AND TIME SETTING
5 Press the SET button.
h The date and time setting is completed, and you are returned to the
Option Menu.
h The Option Menu is canceled when the MENU button is pressed.
HINT
i Under normal conditions, while the battery pack is being replaced, an
internal battery will maintain the date and time settings. However, there is a
small chance the settings may be lost. (The backup will last for about
7 days.) It is recommended to check that the date and time settings are still
correct after replacing the battery pack and before shooting or recording of
any type (follow steps 1 to 3).
To correct the date and time settings
i In step 4, select the indication that you want to change, and follow the
procedure to change the indication.
English 28
BASIC OPERATION
BEFORE TAKING PICTURES
How to hold the camera
Hold the camera securely, keeping your elbows close to your body and
making sure the camera is stable.
Make sure that the lens and flash are not blocked by your fingers or the
handstrap.
HINT
i Images captured in the still image shooting mode can be rotated when
they are played back (page 85).
i When the optical zoom is used or when the autofocus is operating, the
image may appear to waver, but this is not a malfunction.
A finger is blocking the lens or flash.
Correct hold Incorrect hold
29 English
BEFORE TAKING PICTURES
About the touch sensor (touch focus)
With the touch sensor, the image is focused simply by a light finger-touch on
the shutter button (focus lock). With the subject in focus, just gently press the
shutter button to take the picture for a perfectly focused image.
At the same time, the touch sensor is temporarily deactivated whenever the
Recording Menu (page 66) is displayed, thereby facilitating operation of these
screens.
Furthermore, you can also deactivate the touch sensor so that the autofocus
operates only when you press the shutter button halfway (page 69).
1/102
1/102
1/102
F5.2
F5.2
F5.2
English 30
Using the autofocus
The autofocus will work in almost all situations; however, there are certain
conditions that may cause the autofocus function to not work properly. If the
autofocus function is not working properly, set the focus range to capture
images (page 63).
k Conditions that may cause incorrect focus
The following examples are some of the situations where the autofocus
function may not work.
i Subjects with low contrast, very bright
subjects at the center of the image or
dark subjects or locations
Use the focus-lock function to lock the
focus on an object with contrast at the
same distance as the desired subject.
i Subjects without vertical lines
Use the focus-lock function to lock the
focus while framing the subject vertically,
then re-orient the camera to compose a
horizontally framed image.
31 English
BEFORE TAKING PICTURES
The following examples are some of the situations where the autofocus
function may work, but not as desired.
i When both near and far objects are
present
Use the focus-lock function to lock the
focus on an object at the same distance as
the desired subject, then reposition the
camera to compose the picture.
i Fast-moving subjects
Use the focus-lock function to lock the
focus on an object at the same distance as
the desired subject, then reposition the
camera to compose the picture.
English 32
Switching between the shooting mode and
playback mode
Switch between shooting and playing.
1 Press the ON/OFF button to turn
the camera on.
2 Press the playback button [=].
h Each time the playback button is
pressed, the camera switches
between the shooting mode and
the playback mode.
HINT
To turn the camera on in the playback mode
i Press the playback button [=] for at least 1 second, and the camera will
turn on in the playback mode.
149
100-0001
2008.12.24
2008.12.24
2008.12.24
ON/OFF button
Playback button
[=]
<Shooting mode>
<Playback mode>
33 English
BEFORE TAKING PICTURES
How to switch the shooting mode
Your camera can capture single still photos (single-shot mode), record video
clips (video clip recording mode), and also capture a series of still photos
(sequential shots mode).
1 Press the ON/OFF button to
turn the camera on.
2 Press the [m] button.
h The screen to set the
shooting mode and the self-
timer appears.
3 Press the [m] button to select
the shooting mode.
4 Press the SET button.
h The selected shooting mode
is set.
h An icon in the upper left area
of the monitor indicates the
active shooting mode setting.
149
ON/OFF button
[m] button
SET button
<Shooting mode>
s: Single-shot mode
O: Sequential shots mode
X: Video clip recording mode
English 34
Switching the display mode
In the shooting mode, you can select the either the “settings display mode”
which allows you to confirm the shooting settings on the monitor while you
shoot, or the “normal display mode” in which the setting indications are turned
off, providing a full view of the subject.
1 Press the ON/OFF button to turn
the camera on.
2 Press the SET button.
h Each time the SET button is
pressed, the camera switches
between the settings display
mode and the normal display
mode.
ON/OFF button
SET button
149
<Settings display mode>
<Normal display mode>
35 English
BEFORE TAKING PICTURES
Adjust the monitor brightness
The brightness of the monitor is adjustable. Adjust the brightness to the
optimum readability in the ambient light.
1 Press the ON/OFF button to
turn the camera on.
2 Press the MENU button for at
least 1 second.
h The monitor brightness menu
appears.
3 Press the [n] and [o] buttons
to adjust the brightness.
4 Press the MENU button.
h The monitor brightness is
set, and the monitor
brightness menu is canceled.
HINT
i You can also adjust the monitor brightness by selecting “BRIGHTNESS”
from the Option Menu (page 103).
ON/OFF button
MENU button
[n] and [o] buttons
Monitor
English 36
Hints for taking pictures
Muting the camera sounds
i The operation sounds that are generated, for example, when the shutter
button, MENU button or SET button is pressed, can be muted (page 105).
Where is the image data saved?
i All the image and sound data is recorded in the camera’s internal memory
or on the card installed in the camera.
i When a card is installed in the camera, the data is recorded on the card. If
no card is installed, the data is recorded in the camera’s internal memory.
Taking pictures in backlight conditions...
i When taking pictures with the light coming from behind the subject, due to
the characteristics of the CCD, light lines or ghost patterns (flare effect)
may appear in the captured image. In this situation, it is recommended that
you avoid taking pictures with the subject lit from behind.
Switching the guidance display ON/OFF
i Press the [l] button. Each time the [l] button is pressed, the guidance
display switches between ON and OFF.
149 149
[l]
Touch shutter button
to focus
<Guidance display ON> <Guidance display OFF>
37 English
CAPTURING AND PLAYING BACK STILL IMAGES
There are two modes for capturing still images. In the single-shot mode, one
image is captured each time the shutter button is pressed. In the sequential
shots mode, when you press the shutter button, several successive images
are captured. For more information about taking sequential shots, please see
page 47.
Shooting single shots
1 Set the camera to the single-
shot mode (page 33).
2 Rest your finger on the
shutter button.
h If the touch sensor
(page 69) has been set to
ON, when the shutter button
is touched, the autofocus
operates and the image is
focused (focus lock).
<If the touch sensor is set
to OFF>
h Engage the autofocus by
pressing the shutter button
halfway.
F5.2
F5.2
F5.2
1/102
1/102
1/102
<Single-Shot Screen>
Shutter button
Single-shot icon
English 38
3 Gently press the shutter button.
h Press the shutter button gently, taking care not to
move the camera.
h The image that was captured appears on the
monitor as long as the shutter button is kept
pressed (post view).
4 Release your finger from the shutter button.
h The captured image is recorded.
HINT
When the focus mode (page 74) is set
to the 9-point focus mode B...
i A target mark & on the monitor shows
the area the camera is focusing on.
i The camera automatically determines
the correct focus by measuring from 9
different focus points within the
shooting area. If the target mark is at a
position that is different from the point
you wish to focus on, you can refocus,
for example, by changing the shooting
angle.
i The large target mark appears when
the camera focuses on a wide area in
the center of the screen.
About the focus indicator
i A green focus indicator appears when
the subject is successfully focused, or
a red focus indicator when the camera
was not able to focus the subject.
The shutter speed and aperture are
displayed
i The shutter speed and aperture
settings are also displayed on the
monitor. You can use them as a
reference when shooting.
If the motion alert icon appears...
i During still image shooting, if the shutter speed is slow and the possibility
that the image may be blurred due to camera shake becomes high, the
motion alert icon may appear on the monitor. In this case, use a tripod to
stabilize the camera when shooting, or set the flash operation mode to
automatic (page 59).
i When shooting with the fireworks H scene function, the motion alert icon
always appears, but this is normal.
F5.2
1/102
1/2
F5.2
Shutter speed
Aperture
Target mark
Motion alert icon
Focus indicator
39 English
CAPTURING AND PLAYING BACK STILL IMAGES
Viewing still images
The steps for viewing both single shots and sequential shots are the same.
5 Press the playback button
[=].
h If the playback button [=]
was pressed to turn the
camera on, however, press the
playback button [=] for at
least 1 second.
h The image most recently
captured appears on the
monitor.
6 View other images.
h Press the [l] or [m] button to
display the previous or next
image.
To display the previous image:
Press [l].
To display the next image:
Press [m].
h To return to Shooting Screen,
press the playback button
[=].
<If the camera was turned on by pressing the playback button [
=
]>
h When the playback button [=] or ON/OFF button is pressed, the
camera turns off.
When you are finished viewing images...
i Press the ON/OFF button to turn the camera off.
HINT
For still images with voice memo (page 55)...
i When the shutter button is pressed, the voice memo is played back.
100-0001
100-0001
100-0001
2008.12.24
2008.12.24
2008.12.24
Playback button [=]
English 40
9-image display playback
1 Press the playback button
[=].
2 Press [W] ([P]) on the
zoom switch.
h The 9-image display
appears.
3 Select the image to play
back.
h Press the arrow buttons to
move the orange frame to
the desired image, and
press the SET button.
Instead of pressing the
SET button, you can press
[T] ([]]) on the zoom
switch to show the image
full screen.
100
100
100
0001
0001
0001 0002
0002
0002 0003
0003
0003
0007
0007
0007 0008
0008
0008
0005
0005
0005 0006
0006
00060004
0004
0004
0009
0009
0009
SET button
Zoom switch [W]/[T]
Orange frame
Still image
Image number
Video clip
Arrow buttons
Audio recording
Folder number
41 English
CAPTURING AND PLAYING BACK STILL IMAGES
Quick scroll playback
A convenient way to quick-search when there are many images.
1 Access the 9-image display screen (page 40).
2 Press [W] ([P]) on the zoom
switch.
h The Quick Scroll Playback Screen
appears.
h Press the [G] or [H] button to
display the previous or following
image.
h You can press the [I] or [J] button
to move back or forward 32 files at
a time.
3 Display the desired image, and
press the SET button.
h The selected image is shown full-
screen.
2008.12.24
2008.12.24
2008.12.24
1/9
1/9
1/9
English 42
Folder playback
A convenient way to search through multiple folders, or to search for an image
that was recorded using Screen Capture (page 23 in the SANYO Software
Pack INSTRUCTION MANUAL).
1 Access the Quick Scroll Playback Screen (page 41).
2 Press [W] ([P]) on the zoom
switch.
h The Select Folder Screen appears.
3 Select the desired folder, and press
the SET button.
h The first image in the selected
folder is displayed.
h At this time, if you press [W] ([P])
on the zoom switch, the images in
the selected folder are shown in the
9-image display. If [W] ([P]) on
the zoom switch is then pressed
again, you are returned to the Quick
Scroll Playback Screen.
100SANPH
101SANPH
102SANPH
1
2
3
OK
OK
OK
SELECT
SELECT
SELECT
SELECT FOLDER
SELECT FOLDER
SELECT FOLDER
43 English
CAPTURING AND PLAYING BACK STILL IMAGES
Magnifying (zooming in) the image
1 Display the image that you want to magnify.
2 Press [T] ([]]) on the zoom
switch.
h Magnification is enabled.
h The image is magnified, and the
central portion of image is
displayed.
h Press the arrow buttons to view
different parts of the magnified
image.
To magnify:
Magnification increases with each
press of [T] ([]]) on the zoom
switch.
To go back:
Magnification decreases with each
press of [W] ([P]) on the zoom
switch.
h Press the SET button to return to
the normal (100%) view.
HINT
The magnified portion of the image can be saved as a separate image
i Press the shutter button. The magnified portion is saved as a new still
image.
111%
111%
111%
Press shutter to save
Press shutter to save
Press shutter to save
Move
Move
Move
100%
100%
100%
English 44
Zoom jump playback
You can magnify a portion of a still image to check the accuracy of the focus.
1 Display a still image to view
using zoom jump playback.
2 Press the SET button.
h The image is magnified.
h If the magnified view appears
to be in focus, then the
overall image will be in focus.
3 Press the arrow buttons to
move to the part you wish to
magnify, and press [T] ([]])
on the zoom switch.
h The displayed area is further
magnified.
To magnify further:
Magnification increases with
each press of [T] ([]]) on the
zoom switch.
To go back:
Magnification decreases with
each press of [W] ([P]) on the
zoom switch.
h Press the SET button again
to return to the normal size
(100%) screen.
1140%
Press shutter to save
Move
100%
SET button
Zoom switch [W]/[T]
Arrow buttons
45 English
CAPTURING AND PLAYING BACK STILL IMAGES
Deleting files
You can delete files that are stored on the card if you no longer need them.
You can delete the files one at a time, or all at once.
1 To delete files from the card, perform the delete procedure with the
card installed in the camera. To delete files from the camera’s
internal memory, remove the card before performing the delete
procedure.
2 Set the camera to the playback
mode, and press the [n] button.
h The Delete Screen appears.
ALL FILES:
Deletes all the files.
1 FILE:
Deletes one file at a time.
3 Delete the files.
<To delete all the files>
1 Use the [l] and [m] buttons to view the images and check if it is OK
to delete all the files.
2 Press the [n] or [o] button to select “ALL FILES”.
3 Press the SET button.
h The Delete Confirmation Screen appears. To delete the files,
select “YES”, and press the SET button. When the file delete is
completed, “No image” is shown.
Zoom I/O
Zoom I/O
Zoom I/O
DELETE
DELETE
DELETE
ALL FILES
1 FILE
DELETE
DELETE
DELETE
English 46
<To delete one file>
1 Use the [l] and [m] buttons to display the file you wish to delete.
2 Press the [n] or [o] button to select “1 FILE”.
h There is no confirmation screen when deleting single files. Before
pressing the SET button in step 3, please make sure that the
displayed image is one you wish to delete.
3 Press the SET button.
h The currently displayed file is deleted.
h To delete other files, repeat steps 1 to 3.
CAUTION
About protected images
i Files that are protected from accidental delete cannot be deleted. To delete
protected files, set the protect setting for the file to off (page 84), and then
follow the file delete procedure.
47 English
SHOOTING SEQUENTIAL SHOTS
When the shutter button is pressed, still images are captured in succession.
1 Set the camera to the sequential
shots mode (page 33).
2 Press the shutter button to start
shooting.
h Shooting sequential shots begins.
<Estimated maximum number of
sequential shots>
* The quantities indicate the number of shots when the compression
rate is set to j.
* The maximum number of sequential shots will differ depending on the
subject.
h Note that if the shutter button is released during shooting, shooting
stops immediately.
Resolution Max. no. of shots
E Approx. 7 shots
N Approx. 9 shots
D Approx. 12 shots
z Approx. 19 shots
t Approx. 40 shots
[ Approx. 170 shots
143
Sequential shots icon
English 48
HINT
About the focus when shooting sequential shots
i When sequential shots are captured, the autofocus operates when the
focus lock is activated, fixing the focus.
Can the self-timer and/or flash be used?
i The self-timer and flash do not operate when shooting sequential shots.
i The following scene functions cannot be set.
\]H_a5
49 English
VIDEO CLIP RECORDING AND PLAYBACK
Recording a video clip
1 Set the camera to the video
clip recording mode
(page 33).
2 Press the shutter button.
h Video clip recording
begins. During recording,
the length of the video clip
and the remaining
recording time available
are shown on the monitor.
h It is not necessary to
continue pressing the
shutter button while
shooting.
3 End the recording.
h Press the shutter button
again to stop recording and
save the video clip.
00:45:00
00:45:00
00:45:00
00:45:00
00:45:00
00:00:30
Shutter button
Video clip recording icon
Recorded length (time) of
video clip
Remaining recording time
available
English 50
Playing back the video clip
4 Press the playback button
[=].
h If the playback button [=]
was pressed to turn the
camera on, however, press
the playback button [=] for
at least 1 second.
h The video clip just recorded
appears on the monitor.
h Video clips are indicated by
a video clip pattern along
the top and bottom of the
screen.
5 Press the SET button.
h Video clip playback begins.
h To stop playback, press the
[o] button.
PLAY
Playback button [=]
Video clip pattern
[o] button
SET button
51 English
VIDEO CLIP RECORDING AND PLAYBACK
Outline of playback operation
To do this... Do this
Stop playback During playback, press the [o] button.
Pause
During playback, press the SET button.
During accelerated or slow playback, press
the [n] button.
To extract a still image
While playback is paused, press the shutter button.
To play back
one image
at a time
(single-
frame step)
Forward
While playback is paused, press the [m]
button.
Reverse
While playback is paused, press the [l]
button.
Slow
playback
Forward
While playback is paused, press and hold the
[m] button.
Reverse
While playback is paused, press and hold the
[l] button.
To
accelerate
playback
Forward
During forward playback, press the [m] button.
* The playback speed changes each time the
[m] button is pressed, as follows:
Normal playback
10× 15×
Press the [l] button to resume normal
playback speed.
Reverse
During forward playback, press the [l] button.
* The playback speed changes each time the
[l] button is pressed, as follows:
15× 10×
Press the [m] button to resume normal
playback speed.
Return to normal playback
speed
Press the SET button.
Adjusting the volume
Louder: During playback, press [T] on the
zoom switch.
Softer: During playback, press [W] on the
zoom switch.
English 52
When you are finished viewing video clips...
i Press the ON/OFF button to turn the camera off.
CAUTION
How to save one frame from a video clip as a still image
1 Play back the video clip. Pause the playback at the point you wish to
“snap” a photo.
2 Press the shutter button.
i The currently displayed frame is saved as a still image.
The data for a video clip is very large
i Therefore, be aware that if the video clip is uploaded to a computer to be
played back, the computer may not be able to play back the video fast
enough, making it appear jerky. (The video will always be displayed
properly on the camera monitor.)
If video clip recording stops even when there is card memory
remaining…
i Depending on the card you are using, recording may stop even if there is
remaining memory in the card.
i For video clip recording, it is recommended that a high-speed memory
card be used.
If no audio is heard...
The audio is not played back when the video clip is played back in the frame-
by-frame, slow playback, fast playback or reverse playback mode.
During video clip playback, the sound of a motor is audible...
i During recording, the sound of the optical zoom movement or autofocus
movement was recorded. This is not a malfunction.
53 English
USING THE SCENE FUNCTION
You can select from a variety of preset settings (aperture, shutter speed, etc.)
for specific shooting conditions.
1 Set the camera to the shooting
mode (page 32), and press the
SCENE button.
h The screen to select a scene
function appears.
2 Use the arrow buttons to select the
desired setting.
<Features of each scene function>
Scene function Features
Shooting mode setting
s O X
X
Auto
The camera makes the
optimum settings.
mmm
Y
Sports
Capture a split-second image
of a fast-moving subject.
mmm
G
Portrait
Enhance the three-
dimensional feel of the
subject by blurring the
background. (With face
chaser function)
mmm
\
Landscape
For beautiful shots of distant
scenery.
mnm
]
Night view
portrait
Photograph the subject while
keeping the background
night scenery.
mnm
H
Fireworks
For capturing fireworks at
night.
mnm
_
Lamp
Photograph in low-light
conditions.
mnm
AUTO
AUTO
AUTO
Use auto settings
Use auto settings
Use auto settings
<Example: In the single-
shot mode>
English 54
m: Available n: Not available
*
: Disabled during recording
3 Press the SET button.
h This completes the scene select
setting.
h The display returns to the Shooting
Screen.
h The scene function setting is shown
on the monitor.
Scene function Features
Shooting mode setting
s O X
a
Still image with
audio
Shoot a still image and add a
voice memo.
mnn
5
Best shot
Four successive still images
are captured as the exposure
changes.
mnn
r
Face chaser
The subject’s face is kept in
focus and the exposure
adjusted as the image is
captured.
mm
*
m
*
F
Cosmetic
Enhance skin tones during
close-up shots.
mmm
8
Monochrome
Create black-and-white
photos.
mmm
9
Sepia
Create sepia-tone photos. mmm
>
Contrast
Accentuates the light and
dark areas in the image.
mmm
@
Vivid
Accentuates the colors in the
image.
mmm
6
Scene function setting
(X is not displayed)
55 English
USING THE SCENE FUNCTION
Capture a still image with a voice memo
With the still-image-plus-audio a scene function, you can add an audio
track (about 10 seconds maximum) to a captured still image. This audio track
is called a “voice memo”.
1 On the screen to select a scene function (page 53), select a, and
press the SET button.
2 Press the shutter button to take the
picture, then speak into the
microphone.
h During recording, be careful not to
obstruct the microphone with your
fingers, for example.
h Audio recording begins. During
recording, the length of the audio
track and the remaining recording
time available are shown on the
monitor.
h The maximum recording time for a
voice memo is about 10 seconds.
h To end the recording before
10 seconds has elapsed, press the
shutter button.
00:00:02
00:00:08
Recorded length of
audio track
Remaining recording time
available
English 56
How to use the best shot feature
1 Set the camera to the single-shot mode; on the screen to select a
scene function (page 53), select 5; and press the SET button.
2 Press the shutter button.
h While the settings change, four still
images are shot in sequence.
h After the images are captured, the
four still images are displayed on
the monitor.
<To save all four images>
h With all four images showing on the
monitor, press the MENU button.
3 Use the arrow buttons to move the orange frame to the image you
wish to save.
h For a full-size view of the selected image, press the SET button.
h With the full-size view active, you can use the [l] and [m] buttons to
view the previous or next image.
h To return to the screen in step 2, press the MENU button.
4 With the full-size view of the image
you wish to save, select “YES”, and
press the SET button.
h The image currently displayed is
saved, and the other images are
deleted.
SAVE ALL
SAVE ALL
SAVE ALL
OK
OK
OK
SELECT
SELECT
SELECT
EXIT
YES
OK
OK
OK
Delete other images?
Delete other images?
Delete other images?
57 English
USING THE SCENE FUNCTION
How to use the face chaser feature
To attain the best possible face shots, the camera automatically focuses on
the face and adjusts the exposure.
1 On the screen to select a scene function (page 53), select r, and
press the SET button.
2 Aim the camera lens at the subject.
h The camera searches for the
subject’s face. When it detects the
face, a green frame appears.
h Do not touch the shutter button while
the camera is searching. The
camera cannot search when the
autofocus is activated.
3 The focus locks on the subject (page 37).
h The camera focuses on the subject and the exposure is adjusted.
h When the face is in focus, the green frame changes to orange.
4 Press the shutter button.
h The image is captured.
CAUTION
i The digital zoom is disabled.
i The face chaser function does not work when zooming in or out.
i The face chaser function may not work when the subject’s face in the
monitor is relatively small or appears dark.
2
2
143
Green frame
English 58
USING THE ZOOM
Your camera has two zoom functions: optical zoom and digital zoom.
1 Set the camera to the shooting
mode (page 32), and point the
camera lens at the subject.
2 Press the zoom switch to
compose the desired image.
[T]: Zoom in on the subject.
[W]: Zoom out.
h When the zoom switch is
pressed, the zoom bar appears
on the monitor.
h When the optical zoom factor is
at maximum, zooming stops
temporarily. When [T] on the
zoom switch is pressed again,
the mode changes to the digital
zoom mode and zooming
continues.
3 Take the picture.
HINT
Can’t access the digital zoom?
i The digital zoom cannot be used when the face chaser r or portrait
mode
G
scene function is active, or the focus mode is set to AF seeker
p.
Can’t access the optical zoom?
i When the focus range is set to pan o or during video clip recording, the
optical zoom cannot be used.
Zoom switch [W]/[T]
Zoom bar
Monitor
Pointer
When both optical
and digital zoom
are enabled
Digital zoom (yellow)
Optical zoom
When optical zoom
only is enabled
When digital zoom
only is enabled
59 English
FLASH SETTING
The flash is used not only for taking pictures where there is insufficient light,
but also when the subject is in shade or in backlight conditions. Your camera’s
flash has four modes of operation (auto mode, forced flash mode, flash off
mode and red-eye reduction mode). Select the flash mode that is appropriate
for the surrounding conditions. The flash can be enabled only when taking
single-shot still images.
1 Set the camera to the single-shot
mode (page 33), and press the [n]
(?) button.
h The flash menu appears.
k: The camera will detect the
subject brightness and use the
flash only when required. In a
backlight situation, if only the
center of the image is very dark,
the flash will operate to
compensate (auto).
m: The flash will operate with every
image captured regardless of the
conditions. Use this setting
under backlight conditions, when
the subject is in shade, under
fluorescent lighting conditions,
etc. (forced flash).
l: The flash will not operate even in
dark situations. Use this setting
when capturing an image in a
location where flash
photography is prohibited, or
when shooting a night landscape
scene (flash off).
J: The digital camera will detect the subject brightness and use the
flash only when required. At this time the flash will operate in a
manner that reduces the red reflection (“red-eye”) in the subject’s
eyes (red-eye reduction).
[n] (?) button
FLASH
AUTO
Flash menu
English 60
2 Press the [n] or [o] button to select the desired flash mode, and
press the SET button.
3 Press the shutter button.
h The picture is snapped and the flash operates according to the
selected mode.
HINT
When auto is selected...
i The k icon indicating the flash setting is not shown on the Shooting
Screen.
When auto or red-eye reduction is selected...
i When the subject is in focus, if the camera determines that the flash is
necessary, a k or J icon appearing on the monitor indicates that the
flash will operate.
61 English
SELF-TIMER
Self-timer photography is available in the single-shot mode.
1 Set the camera to the single-shot
mode (page 33), and press the
[m] ( ) button.
h The self-timer menu appears.
2 Use the [n] and [o] buttons to
select the desired self-timer
setting, and press the SET
button.
h The self-timer is set, and you are
returned to the Shooting Screen.
y: The image is captured about
2 seconds after the shutter
button is pressed.
x: The image is captured about
10 seconds after the shutter
button is pressed.
Self-timer menu
[m] ( ) button
1
PHOTOGRAPH 1 IMAGE
English 62
HINT
i The countdown time until shutter
release is shown graphically on the
monitor.
To pause or cancel the self-timer function...
i If the shutter button is pressed again before the shutter is released, the
self-timer countdown temporarily stops. Press the shutter button one more
time to restart the self-timer.
i To cancel self-timer photography, set the self-timer setting to off s.
i After the self-timer picture is snapped, the self-timer is automatically reset
to off.
When x is selected...
i When the shutter button is pressed,
the self-timer indicator flashes for
approximately 10 seconds, after
which shooting begins.
i About 3 seconds before shooting,
the self-timer indicator flashes
faster.
1/102
F5.2
Self-timer indicator
63 English
FOCUS RANGE
1 Set the camera to the shooting
mode (page 32), and press the [o]
(R) button.
h The focus range menu appears.
o: The focus operates within the
ranges shown below (pan).
<Still image shooting>
i At maximum aperture setting:
2.2 m (7.22 ft.) to
i At minimum aperture setting:
1.3 m (4.27 ft.) to
<Video clip recording>
i Wide end:
At maximum aperture setting:
45 cm (17.72 in.) to
At minimum aperture setting:
28 cm (11.02 in.) to
i Tele end:
At maximum aperture setting:
4.8 m (15.75 ft.) to
At minimum aperture setting:
4.2 m (13.78 ft.) to
*: The camera automatically
focuses on the subject within a
range of 40 cm (15.75 in.) (Wide
end) or 90 cm (2.95 ft.) (Tele
end) to infinity (auto).
+: You can focus on a subject within
the following ranges (macro):
Wide end: 10 cm (3.94 in.) to
50 cm (19.69 in.)
Tele end: 60 cm (23.62 in.) to
1 m (3.28 ft.)
-: The focus can be manually set to
any distance from 10 cm
(3.94 in.) to 10 m (32.81 ft.), as
well as to infinity (manual).
FOCUS
AUTO
[o] (R) button
Focus range menu
English 64
2 Press the [n] or [o] button to select the desired focus range, and
press the SET button.
h The specified focus range is set, and the camera returns to the
Shooting Screen.
HINT
i In the single-shot mode and sequential shots mode, when the focus range
is set to macro +, the zoom is automatically set to one step from the
wide end. When the focus range is set to pan o, the zoom is
automatically set to the Wide end.
65 English
FOCUS RANGE
How to use the manual focus
1 Select manual - from the focus
range menu, and press the SET
button.
h The focus distance adjustment bar
appears.
2 Press the [l] or [m] button to adjust
the focus distance, and press the
SET button.
h The focus distance is set, and you
are returned to the Shooting
Screen.
HINT
About the focus range
i The focus distance indication shows the distance between the lens surface
and the subject.
i In some cases there may be a slight variance between the distance
(numerical figure) you set in the manual focus mode and the actual
distance. Use the monitor to confirm the focus and compose the photo.
About zoom movement when using the manual focus
i If the focus distance is set to 50 cm (19.69 in.) or less, the zoom changes
to the largest setting that is suitable for that focus distance.
i When the focus distance is set to 50 cm (19.69 in.) or less, the zoom will
function only within the range at which the image is focused.
80cm
English 66
SHOOTING
ACCESSING THE RECORDING MENU
Detailed shooting settings are accessed from the Recording Menu.
1 Set the camera to a shooting
mode (page 33).
2 Press the MENU button.
h The Recording Menu
corresponding to the shooting
mode set in step 1 appears.
h The Recording Menu can be
canceled by pressing the MENU
button.
10
M
1/2RECORDING MENU
TOUCH SENSOR
RESOLUTION
COMPRESSION
EXP MEASURE
FOCUS MODE
ISO
OK EXIT
MENU button
67 English
ACCESSING THE RECORDING MENU
Overview of the Recording Menu
i 7 through 9 are displayed when you press the [n] or [o] button to scroll.
OFF
10
M
1
2
3
4
5
6
7
8
9
0
1/2RECORDING MENU
TOUCH SENSOR
RESOLUTION
COMPRESSION
EXP MEASURE
FOCUS MODE
ISO
OK EXIT
WHITE BALANCE
EXP COMPENSATION
INSERT DATE ON IMAGE
English 68
1 Touch sensor menu (page 69)
2 Resolution menu/video size
menu (page 70)
3 Compression rate menu
(single-shot/sequential shots
mode only) (page 73)
4 Focus mode menu (page 74)
5 Light-measuring mode menu
(page 76)
6 ISO sensitivity menu
(page 77)
7 White balance menu (page 79)
8 Exposure correction menu
(page 80)
h Change the brightness of the
image.
9 Date imprint menu (page 81)
h Imprint the capture date on still
images.
i When you specify multiple functions that cannot be simultaneously
enabled, the function which was last set becomes the active setting, and
the other settings accordingly change automatically.
#: Set the shutter button
touch sensor to ON.
$: Set the shutter button
touch sensor to OFF.
<Single-shot/sequential shots
mode>
k:
Shoot at 3648
×
2736 pixels
(single-shot mode only)
N:
Shoot at 3648
×
2056 pixels
(16:9 aspect ratio)
D:
Shoot at 2816
×
2112 pixels
z:
Shoot at 2288
×
1712 pixels
t:
Shoot at 1600
×
1200 pixels
[: Shoot at 640 × 480 pixels
<Video clip recording mode>
d: Shoot at 640 × 480 pixels
5: Shoot at 320 × 240 pixels
<: Make an audio recording
(page 71)
j: For shooting at low
compression
0: For shooting at normal
(moderate) compression
B: 9-point focus mode
C: Spot focus mode
p: The focus follows the
focus-locked subject.
X: Multi-section light-
measuring
W: Center-weighted light-
measuring
Y: Spot light-measuring
t: Sets the ISO sensitivity
automatically (ISO50 to
200).
*:ISO50
u: ISO100
v: ISO200
w: ISO400
6: ISO800
-: ISO1600
S: ISO2500
>: The camera will determine
the setting automatically.
r : For photography in fair
weather (sunny) conditions
o: In overcast conditions
p: Under fluorescent lighting
q: Under incandescent
lighting
^: For setting the most
accurate white balance
69 English
TOUCH SENSOR (TOUCH FOCUS) SETTING
The touch sensor function, by which the autofocus is activated by a finger-
touch on the shutter button, can be set to ON or OFF. When the touch sensor
function is set to OFF, the autofocus is activated when you press the shutter
button halfway; then gently press the shutter button to snap the picture.
1 Display the Recording Menu (page 66).
2 Select “TOUCH SENSOR” and press the SET button.
h The sensor menu appears.
3 Select the desired icon, and press the SET button.
h The selected touch sensor function is set.
CAUTION
i When the camera is attached to a tripod, the touch sensor sensibility may
be diminished. This happens because the touch sensor works by detecting
changes in the capacitance when the camera is touched with bare hands.
The touch sensor sensibility will also be diminished, for example, if you
hold the camera with gloved hands.
i When the camera is used near inverter-type fluorescent lights, the touch
sensor sensitivity may be diminished.
#: The touch sensor function is set to ON.
$: The touch sensor function is set to OFF.
English 70
RESOLUTION/VIDEO SIZE SETTING
By setting the image resolution (pixels) to a higher setting, image detail is
enhanced for a smoother, finer picture. However, the file size also becomes
large and uses more memory. Select the resolution setting that suits your
purpose.
1 Display the Recording Menu (page 66).
2 In the single-shot or sequential shots mode select “RESOLUTION”,
or in the video clip recording mode select “CLIP SIZE”, and press
the SET button.
h The resolution menu or video size menu appears.
<Single-shot/sequential shots mode>
<Video clip recording mode>
3 Select the desired icon, and press the SET button.
h The selected resolution setting or video size setting is set.
k: Shoot image at 3648 × 2736 pixels (Single-shot mode only)
N: Shoot image at 3648 × 2056 pixels (16:9 aspect ratio)
D: Shoot image at 2816 × 2112 pixels
z: Shoot image at 2288 × 1712 pixels
t: Shoot image at 1600 × 1200 pixels
[: Shoot image at 640 × 480 pixels
d: Shoot at 640 × 480 pixels
5: Shoot at 320 × 240 pixels
<: Make an audio recording (page 71)
71 English
RESOLUTION/VIDEO SIZE SETTING
Record and play back an audio file
In the video clip recording mode, your camera can make audio recordings.
The audio recordings are monaural.
k Record an audio file
1 Display the Recording Menu for the video clip recording mode
(page 66).
2 Select the audio recording icon < from the video size menu, and
press the SET button.
3 Press the MENU button.
h The recording mode is enabled.
4 Press the shutter button.
h Audio recording begins. During
recording, the length of the audio
track and the remaining recording
time available are shown on the
monitor.
h It is not necessary to continue
pressing the shutter button while
recording.
h Take care not to cover the
microphone with your fingers.
5 End the recording.
h Press the shutter button again to stop recording.
02:03:19
00:00:14
Recorded length of
audio track
Remaining recording time
available
English 72
k Playing back audio recordings
1 Display the desired audio data.
h A musical note graphic appears on
the screen.
2 Play back the recording.
HINT
i During 5× or faster accelerated playback, the audio is not played back.
To do this... Do this
Forward playback Press the SET button.
Stop playback During playback, press the [o] button.
Pause
During playback, press the SET button.
During fast forward or fast reverse, press the
[n] button.
Fast forward
During forward playback, press the [m] button.
* The speed changes each time the [m] button
is pressed, as follows:
Normal playback
10× 15×
Press the [l] button to resume normal speed.
Fast reverse
During forward playback, press the [l] button.
* The speed changes each time the [l] button
is pressed, as follows:
15× 10×
Press the [m] button to resume normal speed.
Return to normal playback speed
Press the SET button.
Adjusting the volume
Louder: During playback, press [T] on the
zoom switch.
Softer: During playback, press [W] on the
zoom switch.
101-0018
2008.12.24
PLAY
73 English
COMPRESSION RATE SETTING
Set the data compression rate when shooting images. Even if the same
resolution is used, you can change the compression setting to decrease the
image data size so that you can capture more images, or increase the image
data size for no loss in image quality.
1 Display the Recording Menu (page 66).
2 Select the compression rate menu, and press the SET button.
h The menu to select the desired compression rate is shown.
j: Stores the data at a low compression rate. The file size is large,
but the image quality is optimum.
0: Stores the data at a normal compression rate. The file size is
smaller, but the image quality is reduced.
3 Select the desired compression rate from the compression menu,
and press the SET button.
h This completes the compression rate setting.
English 74
FOCUS AREA SETTING
You can choose from different types of autofocus:
9-point range finder focus:
The correct focus is determined from 9 different focus points within the
shooting area visible on the monitor. When the image is focused, a target
mark & appears.
Spot focus:
The camera focuses on the subject in the center of the monitor.
AF seeker:
Once the focus is locked on a subject (page 37), it follows the subject. The
focus point automatically changes to remain continuously focused on a
moving subject.
1 Display the Recording Menu (page 66).
2 Select “FOCUS MODE” and press the SET button.
h The focus mode menu appears.
B: 9-point range finder focus is selected (page 38).
C: Spot focus is selected.
p: AF seeker is selected.
h When the C or p setting is
selected, the focus mark appears in
the center of the monitor.
3 Select the desired icon, and press
the SET button.
h The focus area is set.
143
Focus mark
75 English
FOCUS AREA SETTING
HINT
When spot focus is selected...
i The focus mark + appears in the center
of the monitor.
When AF seeker is selected...
i The focus mark + appears in the
center of the monitor.
i When the focus-lock is activated, the
seeker mark appears on the focused
subject.
i During focus-lock, even if the focused
subject moves, the seeker mark
automatically follows the subject.
i If the camera loses the focus-lock on
the subject, the seeker mark
disappears.
i In dark environments, the seeker mark
may follow the subject more slowly.
i When the p setting is selected, the
digital zoom is not available.
1/83
1/83
1/83
F5.0
F5.0
F5.0
Seeker mark
English 76
LIGHT-MEASURING MODE SETTING
You can select from 3 types of light-measuring modes.
Multi-section light-measuring:
The exposure is adjusted after sampling from multiple areas of the entire
shooting screen.
Center-weighted light-measuring:
The exposure is adjusted after light is measured from the entire image, but
with emphasis on the center area.
Spot light-measuring:
You can compose the picture and capture the image after first measuring the
light only at the center spot of the monitor.
1 Display the Recording Menu (page 66).
2 Select “EXP MEASURE”, and press the SET button.
h The light-measuring mode menu appears.
n: Multi-section light-measuring
W: Center-weighted light-measuring
Y: Spot light-measuring
3 Select the desired icon, and press the SET button.
h This completes the light-measuring mode setting.
77 English
ISO SENSITIVITY
With the initial settings, the ISO sensitivity is automatically set according to
the brightness of the subject. However, the ISO sensitivity can be set to a
fixed setting.
1 Display the Recording Menu (page 66).
2 Select “ISO” and press the SET button.
h The ISO sensitivity menu appears.
3 Select the desired icon, and press the SET button.
h The ISO sensitivity is set.
t: Sets the ISO sensitivity automatically (ISO50 to 400 [video clip
recording mode: ISO450 to 3600]).
*: Sets the sensitivity to ISO50 (video clip recording mode: ISO450).
u: Sets the sensitivity to ISO100 (video clip recording mode: ISO900).
v: Sets the sensitivity to ISO200 (video clip recording mode:
ISO1800).
w: Sets the sensitivity to ISO400 (video clip recording mode:
ISO3600).
6: Sets the sensitivity to ISO800 (video clip recording mode:
ISO7200).
-: Sets the sensitivity to ISO1600 (video clip recording mode:
ISO7200).
S: Sets the sensitivity to ISO2500 (video clip recording mode:
ISO7200).
English 78
HINT
i By setting a higher ISO sensitivity, you can set higher shutter speeds and
capture images in darker locations, but noise in the captured images may
increase.
CAUTION
Does the image appear to flicker when recording a video clip?
i If recording a video clip under fluorescent lights with the ISO sensitivity set
to w or higher, a noticeable flicker may appear in the image.
79 English
WHITE BALANCE
This camera automatically adjusts the white balance under most lighting
conditions. However, if you want to specify the lighting conditions or change
the overall tone of the image, the white balance can be manually set.
1 Display the Recording Menu (page 66).
2 Select “WHITE BALANCE” and press the SET button.
h The white balance menu appears.
Select the ^ icon from the white balance menu, fill the entire screen with
a plain white paper, and press the SET button to set the white balance. To
use any of the other white balance settings, proceed to step 3.
3 Select the desired icon, and press the MENU button.
h This completes the white balance setting.
HINT
To cancel the white balance setting
i Perform steps 1 and 2, select >, and then press the MENU button.
>: The camera will make the white balance adjustment automatically
based on the natural and artificial light conditions. This is the setting
used in the auto mode.
r : For shooting outside on a sunny day.
o: For shooting outside on a cloudy day.
p: For shooting inside under fluorescent lighting.
q: For shooting inside under incandescent lighting.
^: For more accurate adjustment or when the light source cannot be
specified (one-push).
English 80
EXPOSURE CORRECTION
When capturing images, you can make the image lighter or darker.
1 Point the camera lens at the subject, and display the Recording
Menu (page 66).
2 Select “EXP COMPENSATION” and press the SET button.
h The screen to adjust the exposure appears.
3 Use the [n] and [o] buttons to select the desired exposure
numerical value, and press the SET button.
h The specified exposure is set, and you are returned to the Recording
Menu.
HINT
i The exposure correction setting returns to ±0 after the camera is turned
off.
81 English
DATE IMPRINT
You can choose to have the date the image was captured imprinted on the
image.
1 Display the Recording Menu (page 66).
2 Select “INSERT DATE ON IMAGE”, and press the SET button.
h The date imprint menu appears.
ON: The date of the capture is imprinted on the image.
OFF: The date of the capture is not imprinted on the image.
3 Press the [n] or [o] button to select the desired setting, and press
the SET button.
h The date imprint mode is set, and you are returned to the Recording
Menu.
HINT
About the capture date and date imprinting
i When an image is edited, the date of the image file changes to the date
and time the image was edited. However, the imprinted capture date
remains unchanged.
Is the sequential shots speed slow?
i When the date imprint mode is set to “ON”, the sequential shots speed
may become slower.
If the imprinted date is shown as [- - - - .- - .- -] …
i The date and time settings have not yet been completed. Set the camera
to the correct date and time (page 25).
English 82
PLAYBACK
PAGE 1 (BASIC SETTINGS)
DISPLAYING THE PLAYBACK MENU
The Playback Menu is used to adjust your camera’s playback settings.
1 Press the playback button [=].
h The display changes to the
Playback Screen.
2 Press the MENU button.
h The Playback Menu appears.
h The Playback Menu is canceled
when the MENU button is
pressed.
PROTECT
SLIDESHOW
ROTATE
BLUR CORRECTION
CONTRAST CORRECT
RED-EYE CORRECT.
PLAYBACK MENU 1/2
OK EXIT
Playback button [=]
MENU button
83 English
DISPLAYING THE PLAYBACK MENU
Overview of the Playback Menu
1 [Slideshow] (page 100)
h Play back the images in a
slideshow format.
2 [Protect] (page 84)
h Protect data from accidental
erasure (write protect).
3 [Rotate image] (page 85)
h Rotate still images.
4 [Blur correction] (page 87)
h Correct the effects of camera
shake in still images.
5 [Contrast correction]
(page 89)
h Add contrast (light and dark) to
the image to make it clearer.
6 [Red-eye correction] (page 91)
h Repair the red-eye effect to
make eyes look more natural.
7 [Resize] (page 86)
h Reduce the resolution of a still
image.
8 [File Copy] (page 93)
h Copy files from the card to the
internal memory, or vice versa.
9 [Print instructions] (page 95)
h Specify the print settings.
i 7 through 9 are displayed when you press the [n] or [o] button to scroll.
1
2
3
4
5
6
7
8
9
RESIZE
FILE COPY
PRINT INSTRUCTIONS
PROTECT
SLIDESHOW
ROTATE
BLUR CORRECTION
CONTRAST CORRECT
RED-EYE CORRECT.
PLAYBACK MENU 1/2
OK EXIT
English 84
IMAGE PROTECT
Prevent accidental erasure of data.
1 Display the data that you want to protect from accidental erasure,
and display the Playback Menu (page 82).
2 Select “PROTECT” and press the
SET button.
h The screen to set the protect
setting appears.
3 Select “YES” and press the SET
button.
h The protect mode is set for the
data.
h The protect mark B indicates that
the data is locked.
CAUTION
i Even if the protect mode is set for certain data files, they will be deleted if
the card is reformatted (page 114).
HINT
To select a different image in steps 2 and 3...
i Press the [l] or [m] button.
To cancel the protect mode for an image...
i Display the desired data and repeat steps 1 to 3.
Lock the file?
Lock the file?
Lock the file?
YES
OK
OK
OK
EXIT
YES
EXIT
Unlock the file?
Unlock the file?
Unlock the file?
OK
OK
OK
85 English
ROTATE IMAGE
Captured still images can be rotated to the correct orientation for viewing.
1 Display the image you wish to rotate, and display the Playback Menu
(page 82).
2 Select “ROTATE” and press the
SET button.
h The screen to rotate the image
appears.
3 Select “YES” and press the SET
button.
h Each time the SET button is
pressed, the image is rotated
another 90 degrees.
HINT
i On the 9-image display playback, rotated images are shown in their
original orientation.
i An image for which the protect (locked) mode has been set cannot be
rotated.
Rotate image?
Rotate image?
Rotate image?
YES
OK
OK
OK
EXIT
English 86
CHANGING IMAGE SIZE (RESIZE)
The size of a still image that has already been captured at a resolution of t
or higher can be changed to 1600 × 1200 pixels or 640 × 480 pixels. The
resized image is saved as a separate image.
1 Display the still image whose size you want to change, and display
the Playback Menu (page 82).
2 Select “RESIZE” and press the SET
button.
h The screen to change the still
image resolution appears.
3 Select the new image size.
4 Press the SET button.
h Resizing begins.
HINT
Why can’t the image be resized?
i An image can be resized only to a smaller (or the same) size, not to a
larger size.
i An image that was captured at a resolution of N cannot be resized.
2
M (1600 × 1200): The saved image will be 1600 × 1200 pixels.
0.3
M (640 × 480): The saved image will be 640 × 480 pixels.
(1600×1200)
(640×480)
OK
OK
OK
Change image resolution?
Change image resolution?
Change image resolution?
87 English
BLUR CORRECTION
Correct the effects of camera movement (camera shake) to produce a
sharper image.
1 Display the image to be modified, and display the Playback Menu
(page 82).
2 Select “BLUR CORRECTION”,
and press the SET button.
h The Blur Correction Screen
appears.
YES:
Proceed with the blur correction.
EXIT:
Return to the Playback Menu.
3 Select “YES”, and press the SET button.
h Image processing begins.
h During image processing, “Processing” is shown on the screen.
h When processing is completed, the modified image is shown. Check
the image to see if the post-processing result is satisfactory.
Proceed with
Proceed with
blur correction?
blur correction?
Proceed with
blur correction?
YES
EXIT
OK
OK
OK
Blur correction icon
English 88
4 If the modified image is satisfactory,
press the SET button.
h The screen to save the corrected
image appears.
h To discontinue the procedure, press
the MENU button. The modified
image is discarded, and you are
returned to the Blur Correction
Screen.
SAVE AS NEW:
The modified image is saved as a
separate image, and the original
image is preserved.
OVERWRITE:
The original file is deleted, and only
the modified image is saved.
5 Select the desired method to save the modified image, and press the
SET button.
h The modified image is saved, and you are returned to the Blur
Correction Screen.
HINT
About the blur correction icon
i
On the Blur Correction Screen, an icon indicating the degree of blur appears.
: Blur correction unnecessary or blur correction completed.
: Blur correction possible
: Blur correction not possible
If the “Blur correction not successful” message appears...
i The camera was not able to successfully repair the image.
i The correction function works to automatically edit flaws that the camera
detects in captured images. In some cases, the camera may not be able to
repair the image.
i
Blur correction is not possible for images captured at a shutter speed of 1/8
sec or less, for resized images, or for images captured using a different
digital camera. Also, blur correction may not be possible in cases of
extreme blur.
Concerning the date and time information for the modified image
i The date display that is shown when an edited image is played back is the
date that the image was saved after it was modified.
OK
OK
OK
Select the type of save
Select the type of save
Select the type of save
SAVE AS NEW
OVERWRITE
89 English
CONTRAST CORRECTION
Add contrast (light and dark) to an image to make it clearer.
1 Display the image to be modified, and display the Playback Menu
(page 82).
2 Select “CONTRAST CORRECT”,
and press the SET button.
h The Contrast Correction Screen
appears.
YES:
Proceed with the contrast
correction.
EXIT:
Return to the Playback Menu.
3 Select “YES”, and press the SET button.
h Image processing begins.
h During image processing, “Processing” is shown on the screen.
h In some cases, it may take several seconds to process the image.
h When processing is completed, the modified image is shown. Check
the image to see if the post-processing result is satisfactory.
EXIT
YES
OK
OK
OK
Autocorrect the contrast?
Autocorrect the contrast?
Autocorrect the contrast?
English 90
4 If the modified image is satisfactory,
press the SET button.
h The screen to save the corrected
image appears.
h To discontinue the procedure, press
the MENU button. The modified
image is discarded, and you are
returned to the Contrast Correction
Screen.
SAVE AS NEW:
The modified image is saved as a
separate image, and the original
image is preserved.
OVERWRITE:
The original file is deleted, and only
the modified image is saved.
5 Select the desired method to save the modified image, and press the
SET button.
h The modified image is saved, and you are returned to the Contrast
Correction Screen.
HINT
Concerning the date and time information for the modified image
i The date display that is shown when an edited image is played back is the
date that the image was saved after it was modified.
OK
OK
OK
OVERWRITE
SAVE AS NEW
Select the type of save
Select the type of save
Select the type of save
91 English
RED-EYE CORRECTION
If you photograph your subjects at night using the flash, they may appear in
the image with glowing red eyes (red-eye effect). Now you can amend the
image so that the subjects’ eyes appear more natural (red-eye correction).
1 Display the image to be modified, and display the Playback Menu
(page 82).
2 Select “RED-EYE CORRECT.”, and
press the SET button.
h The Red-eye Correction Screen
appears.
YES:
Proceed with the red-eye
correction.
EXIT:
Return to the Playback Menu.
3 Select “YES”, and press the SET
button.
h Image processing begins.
h During image processing,
“Processing” is shown on the
screen.
h When processing is completed, the
modified image is shown. Check
the image to see if the post-
processing result is satisfactory.
OK
OK
OK
EXIT
YES
Correct red-eye effect?
Correct red-eye effect?
Correct red-eye effect?
English 92
4 If the modified image is satisfactory,
press the SET button.
h The screen to save the corrected
image appears.
h To discontinue the procedure, press
the MENU button. The modified
image is discarded, and you are
returned to the Red-eye Correction
Screen.
SAVE AS NEW:
The modified image is saved as a
separate image, and the original
image is preserved.
OVERWRITE:
The original file is deleted, and only
the modified image is saved.
5 Select the desired method to save the modified image, and press the
SET button.
h The modified image is saved, and you are returned to the Red-eye
Correction Screen.
HINT
If the “Red-eye correction not successful” message appears...
i The camera was not able to successfully correct the red-eye effect.
i The red-eye correction function works to automatically edit the red-eye
effect that the camera detects in captured images. In some cases, the
camera may fail to correctly detect the red-eye effect, or it may incorrectly
identify the red-eye effect where it does not exist.
Concerning the date and time information for the modified image
i The date display that is shown when an edited image is played back is the
date that the image was saved after it was modified.
NEXT
NEXT
NEXT
93 English
COPY DATA
Images recorded in the camera’s internal memory can be copied to the card,
and likewise from the card to the internal memory.
1 Insert the card in the camera (page 21).
2 Display the Playback Menu (page 82).
3 Select “FILE COPY” and press the
SET button.
h The screen to copy files appears.
4 Select the copy direction.
INT MEM CARD:
Copy image data from the internal
memory to the card.
CARD INT MEM:
Copy image data from the card to the
internal memory.
* If no card is set in the camera, you
cannot copy data.
OK
OK
OK
INT MEM CARD
CARD INT MEM
Copy file?
Copy file?
Copy file?
English 94
5 Press the SET button.
h The screen to select the type of
copy appears.
h The copy source image is shown in
the background on the screen.
COPY SINGLE:
Copy the data for one image.
COPY ALL:
Copy all the data from the copy
source to the copy destination.
6 Select the desired type of copy.
<When selecting COPY SINGLE>
1 Press the [l] or [m] button to display the image you wish to copy.
2 Press the [n] or [o] button to select “COPY SINGLE”.
<When selecting COPY ALL>
1 Press the [n] or [o] button to select “COPY ALL”.
7 Press the SET button.
h The files are copied.
COPY ALL
COPY SINGLE
CARD
CARD
CARD
INT MEM
INT MEM
INT MEM
OK
OK
OK
95 English
PRINT SETTINGS
In addition to using your printer to print out still images captured with your
camera, as with conventional film, you can have prints made at shops offering
digital print services. Moreover, this camera is DPOF-compatible, so you can
use the camera to specify the number of prints, or whether or not the date is
displayed on the print.
Display the screen to set the print settings
1 Display the Playback Menu (page 82).
2 Select “PRINT INSTRUCTIONS” and
press the SET button.
h The screen to set the print settings
appears.
EACH IMAGE:
The print settings are specified for
each individual image.
ALL IMAGES:
The specified print settings apply to
all the still images.
ALL CLEAR:
Clear all the print settings.
Specify the printing
Specify the printing
instructions?
instructions?
Specify the printing
instructions?
EACH IMAGE
ALL IMAGES
ALL CLEAR
OK
OK
OK
English 96
HINT
Printing a single frame from a video clip
i To print with a printer or have the digital print service shop print out a still
image from a video clip, you must first save it (extract still) as a still image
(page 52).
About the DPOF format
i DPOF (Digital Print Order Format) is a print order format. You can connect
your camera to a DPOF-compatible printer to produce your prints. You can
also set the print settings (page 127) for the desired images, and then have
the reserved images printed automatically.
About the finished prints
i Images that have been rotated will be printed in their original orientation.
i The quality of the print output will differ depending on the print service and
printer used.
CAUTION
i It is not possible to set the print settings when there are 10,000 or more
files saved on the card.
97 English
PRINT SETTINGS
Specifying date imprinting and number of prints
You can specify print settings for each individual image (EACH IMAGE), or
apply the print settings to all the images on the card (ALL IMAGES).
1 Display the screen to set the print settings (page 95).
2 Select “EACH IMAGE” or “ALL
IMAGES”.
EACH IMAGE:
The set print settings are applied
only to the image currently
displayed.
ALL IMAGES:
The set print settings are applied to
all the still images on the card.
3 Press the SET button.
h The Date/Copies Print Screen
appears.
h If “EACH IMAGE” was selected,
press the [l] or [m] button to
display the desired image to print.
h The print settings for the currently
displayed image are shown in the
upper left area of the monitor. You
can press the [l] or [m] button to
confirm the print settings for each
image.
Specify the printing
Specify the printing
instructions?
instructions?
Specify the printing
instructions?
EACH IMAGE
ALL IMAGES
ALL CLEAR
OK
OK
OK
0
DATE
DATE
DATE
OK
OK
OK
EACH IMAGE
EACH IMAGE
EACH IMAGE
:
: 0
English 98
4 Specify the number of prints and
whether the date is imprinted.
h Please specify the number of prints
before setting the date imprint
setting. The date imprint setting
cannot be set until the number of
prints has been entered.
<Specifying the number of prints>
h Press the [n] or [o] button to
specify the number of prints.
h Press the [n] or [o] button until
the desired number of prints is
displayed.
<Specifying dated prints>
h Press [W] on the zoom switch to
add a check mark ( ) next to
.
5 Press the SET button.
h This completes the settings for the
number of prints and date
imprinting.
h If you press the MENU button, you
are returned to the screen to set the
print settings (step 1).
CAUTION
i Do not specify dated prints for images that were captured with the date
imprint function (page 81) set to ON, or else the date will appear on the
photo print twice.
1
OK
OK
OK
EACH IMAGE
EACH IMAGE
EACH IMAGE
:
: 0
DATE
DATE
DATE
1
OK
OK
OK
EACH IMAGE
EACH IMAGE
EACH IMAGE
:
: 0
DATE
DATE
DATE
1
OK
OK
OK
EACH IMAGE
EACH IMAGE
EACH IMAGE
:
: 1
DATE
DATE
DATE
99 English
PRINT SETTINGS
Clearing all the print settings
Delete the print settings for all images.
1 Display the screen to set the print settings (page 95).
2 Select “ALL CLEAR”.
3 Press the SET button.
h The Confirm All Clear Screen appears.
YES: Clear the print settings for all images.
EXIT: Cancel the clear procedure and return to the screen to set the
print settings.
4 Select “YES”, and press the SET button.
h All the print settings are cleared and you are returned to the Playback
Menu.
Specify the printing
Specify the printing
instructions?
instructions?
Specify the printing
instructions?
EACH IMAGE
ALL IMAGES
ALL CLEAR
OK
OK
OK
English 100
SLIDESHOW PLAYBACK
1 Display the Playback Menu (page 82).
2 Select “SLIDESHOW” and press the
SET button.
h The screen to set the slideshow
appears.
<Changing the slideshow controls>
1 Select one of the slideshow controls, and press the SET button.
2 Press the [n] or [o] button to change the setting.
3 Press the SET button.
3 Select “START”, and press the SET button.
h Slideshow playback starts.
h To stop slideshow playback, press the SET button or MENU button.
HINT
i Audio data is not played during slideshow playback.
TIME: Adjust the transition speed
(the period that an image
is displayed before it
changes to the next
image).
EFFECT: Select a transition effect
as an image changes to
the next image.
BGM: Specify the settings for
playing background music
during slideshow
playback.
START: Begin slideshow playback.
TIME 3sec
BGM
START
A
EFFECT
OK
OK
OK
Start slideshow
Start slideshow
Start slideshow
101 English
DISPLAYING IMAGE PROPERTIES
(INFORMATION SCREEN)
On the Information Screen you can check what the settings were when an
image was captured.
1 Display the desired image.
2 Press and hold the MENU
button for at least
1 second.
h The Information Screen
appears.
h If the MENU button is
pressed again, the
Information Screen is
canceled.
1 Resolution setting
2 Resolution
3 Scene function setting
4 Image number
5 Protect setting
6 Voice memo setting
7 File size
8 Aperture value
9 Shutter speed
0 Exposure correction
setting
A Video size setting/
audio file indicator
B Resolution and frame
rate
C File format
D Playback time
E Remaining battery power
100-0006
158KB
00:00:20
INFO
A
C
4
5
7
D
E
100-0004
2816×2112
SIZE
IRIS
SHUTTER
EXPOSE
2MB
F3.5
1/50
0
INFO
1
2
4
5
6
7
8
9
@
E
3
100-0005
100-0005
100-0005
320×240 15fps
SIZE
EXPOSE
QTM
5MB
0
00:00:15
INFO
INFO
INFO
A
B
C
4
5
7
D
3
@
E
<Still image playback>
<Video clip playback>
<Audio file playback>
English 102
OPTION
DISPLAYING THE OPTION MENU
The Option Menu is used to adjust various camera settings.
1 Display the Recording Menu or Playback Menu.
h Recording Menu, see page 66
h Playback Menu, see page 82
2 Press the [n] or [o] button to
select the option tab 3.
h The Option Menu appears.
To exit the Option Menu
To return to the Shooting Screen or Playback Screen
Press the MENU button.
To return to the Recording Menu or the Playback Menu
With the option tab 3 selected, press the [n] or [o] button.
0
NTSC
SOUND
CLOCK SET
OPTION MENU
POST VIEW
1sec
BRIGHTNESS
LANGUAGE
TV SYSTEM
1/2
OK EXIT
Option tab
103 English
DISPLAYING THE OPTION MENU
Overview of the Option Menu
NTSC
0
SOUND
CLOCK SET
OPTION MENU
POST VIEW
1sec
BRIGHTNESS
LANGUAGE
TV SYSTEM
1/2
OK EXIT
@
8
7
9
1
2
3
4
5
6
AUTO POWER OFF
FILE NO. CONT’D
FORMAT
RESET SETTINGS
English 104
1 [Date and time setting]
(page 25)
h Set the camera’s internal
clock.
2 [Sounds] (page 105)
h Adjust the sounds produced
by the camera.
3 [Post-view] (page 107)
h Specify how long a still image
is displayed on the monitor
after it is captured.
4 [LCD brightness] (page 35)
h Adjust the brightness of the
monitor.
5 [ language] (page 108)
h Select the language in which
the monitor messages are
displayed.
6 [TV system setting] (page 109)
h Select the type of TV signal
that is output from the
camera’s USB/AV terminal.
7 [Auto power off] (page 110)
h Specify the time elapsed
before the auto power off
function operates to turn the
camera off.
8 [File number memory]
(page 111)
h Set the file number memory
function to ON or OFF.
9
[
Format
]
(page 114)
h Reformat the camera’s internal
memory or the card installed in
the camera.
0 [Reset camera settings]
(page 116)
h Reset the camera to the
factory-preset settings.
i 7 through 0 are displayed when you press the [n] or [o] button to scroll.
105 English
SOUNDS
Set the sounds that are produced by the camera.
1 Display the Option Menu (page 102).
2 Select “SOUND” and press the SET
button.
h The screen to set the sounds
appears.
OPERATION VOL:
Volume setting for all camera buttons.
TURN ON/OFF:
Mute or enable the sound that is
produced when the camera is turned
on or off.
SHUTTER:
Select the sound that is produced
when the shutter button is pressed.
KEY SW:
Select the sound that is produced
when a camera button (SET button,
MENU button, etc.) is pressed.
AUDIO GUIDE:
Mute or enable the camera’s audio
help guide.
PLAY VOLUME:
Adjust the volume for playing back
video clips and audio files.
OK
OK
OK
OPERATION VOL
TURN ON/OFF
SHUTTER
KEY SW
AUDIO GUIDE
PLAY VOLUME
3
ON
D
A
ON
3
SOUND
SOUND
SOUND
English 106
3 Select the desired item, and press the SET button.
4 Press the [n] or [o] button to change the setting.
<If “TURN ON/OFF” or “AUDIO GUIDE” is selected>
h The respective screen to enable or disable the sound appears.
ON: Activates the sound.
OFF: Deactivates the sound.
<If “SHUTTER” or “KEY SW” is selected>
h The respective screen to select the sound appears.
h Select from 5 different sounds (A to E) and “OFF”.
h After selecting a sound, press the [m] button to preview it.
h If “OFF” is selected, no sound is produced.
<If “OPERATION VOL” or “PLAY VOLUME” is selected>
h The screen to select the volume setting appears.
h You can select a volume setting from 1 (minimum) to 5 (maximum).
h If “OFF” is selected, no sound is produced.
5 Press the SET button.
h The sound settings are completed.
h To return to the Option Menu, press the MENU button.
107 English
POST-VIEW SETTING
Specify the duration that the captured image appears on the monitor (post-
view) after the shutter button is pressed.
1 Display the Option Menu (page 102).
2 Select “POST VIEW” and press the SET button.
h The Post View Menu appears.
1sec:
The post-view image is displayed for 1 second.
2sec:
The post-view image is displayed for 2 seconds.
OFF:
The post-view image is not displayed.
3 Select the desired setting, and press the SET button.
h This completes the post-view setting.
English 108
SCREEN LANGUAGE
You can set the monitor of your camera to display the messages in any one of
several languages.
1 Display the Option Menu (page 102).
2 Select “ LANGUAGE” and press
the SET button.
h The screen to select the display
language appears.
3 Select the desired language, and press the SET button.
h The selected display language is set.
LANGUAGE
OK
109 English
TV SYSTEM SETTING
Specify the type of image signal that is output from your camera’s USB/AV
terminal.
1 Display the Option Menu (page 102).
2 Select “TV SYSTEM” and press the SET button.
h The TV System Menu appears.
NTSC:
Outputs NTSC video signals.
PAL:
Outputs PAL video signals.
3 Select the desired setting, and press the SET button.
h The selected TV system is set.
HINT
If no image appears on the TV...
i If the TV system setting is not correct for the connected equipment, no
image will appear on the TV.
English 110
AUTO POWER OFF FUNCTION
Your camera has an “auto power off” function whereby the power
automatically turns off after a specified period of inactivity. The auto power off
function works to conserve the battery pack power when the camera is not
being used, or to prevent the battery pack from dying if the camera has
accidentally been left on. You can specify the elapsed time (standby time)
before the auto power off function operates to turn the camera off.
1 Display the Option Menu (page 102).
2 Select “AUTO POWER OFF” and
press the SET button.
h The screen to set the standby time
appears.
RECORDING:
Set the standby time for the
shooting mode.
PLAYBACK:
Set the standby time for the
playback mode.
3 Select the desired option, and press the SET button.
h The Standby Time Menu appears.
4 Press the [n] or [o] button to select the standby time.
5 Press the SET button.
h The auto power off function is set.
h To return to the Option Menu, press the MENU button.
1 min
3 min
AUTO POWER OFF
AUTO POWER OFF
AUTO POWER OFF
RECORDING
PLAYBACK
OK
OK
OK
111 English
FILE NO. MEMORY
If a newly formatted card is used, the file name (image number) of the
captured image automatically begins from 0001. If the card is subsequently
reformatted, or if a different reformatted card is used, the file names again
begin from 0001. This is because the file number memory function is set to
“OFF”, and consequently it results in more than one card containing images
with the same numbers. By setting the file number memory function to “ON”,
even if the card is reformatted or the card is replaced with another card, the
consecutive numbering of file names continues from the last number
recorded by the camera.
<File number memory function “OFF”>
<File number memory function “ON”>
File name (image number)
Card A 0001, 0002......0012, 0013
Card B 0001, 0002......0012, 0013
File name (image number)
Card A 0001, 0002......0012, 0013
Card B 0014, 0015....... 0025, 0026
Replace card
Replace card
English 112
i If Card B already has files in it when it replaces Card A, file names are
assigned as follows.
When the highest file number on Card B (before replacing) is lower
than the highest file number on Card A: the file name of the next
recorded image continues from last file name recorded on Card A.
When the highest file number on Card B (before replacing) is higher
than the highest file number on Card A: the file name of the next
recorded image continues from last file name recorded on Card B.
HINT
What about the internal memory?
i The file number reset function works the same for the internal memory.
Card A 0001, 0002 ..... 0012, 0013
Card B 0001, 0002, 0014, 0015 ..... 0025, 0026
Previously recorded files
Replace card
Card A 0001, 0002 ..... 0012, 0013
Card B 0020, 0021, 0022, 0023 ..... 0025, 0026
Previously recorded files
Replace card
113 English
FILE NO. MEMORY
1 Display the Option Menu (page 102).
2 Select “FILE NO. CONT’D”, and press the SET button.
ON:
The file number memory function is on.
OFF:
The file number memory function is off.
3 Select the desired setting, and press the SET button.
h The selected file number memory function is set.
HINT
i Until the file number memory function is turned OFF, consecutive file
names are assigned. It is recommended that the file number memory
function be returned to OFF at the end of each photography session.
English 114
INITIALIZING THE CARD MEMORY
AND INTERNAL MEMORY
A card must be formatted with this camera:
i After purchasing, when used for the first time, or
i If it was formatted using a personal computer or another digital camera.
The card cannot be reformatted if the lock switch is set to the “LOCK”
position. Proceed with the reformat procedure after setting the lock switch to
the unlocked position.
1 To reformat a card, install it in the camera. To reformat the camera’s
internal memory, remove the card from the camera.
2 Display the Option Menu (page 102).
3 Select “FORMAT” and press the
SET button.
<Card format>
h The screen to select the type of
format appears.
h Follow steps 4 to 6.
FORMAT:
A normal formatting is executed.
FULL FORMAT:
The entire card is scanned and
reformatted.
<Internal memory format>
h The screen to confirm formatting
appears.
h Follow steps 5 and 6.
OK
OK
OK
FORMAT
FULL FORMAT
( CARD)
( CARD)
( CARD)FORMAT
FORMAT
FORMAT
OK
OK
OK
EXIT
YES
Format
Format
the internal memory?
the internal memory?
Format
the internal memory?
<With card installed>
<No card installed>
115 English
INITIALIZING THE CARD MEMORY AND
INTERNAL MEMORY
4 Select the desired format option, and press the SET button.
h The screen to confirm formatting appears.
5 Select “YES”.
6 Press the SET button.
h Formatting begins.
h During formatting, “Formatting” and “do not power off” are shown on
the monitor.
CAUTION
Caution during reformatting
i Please do not turn off the camera or insert/remove the card while the card
is being formatted.
Reformatting erases the data
i When the card or internal memory is initialized, all the recorded data is
erased. Protected data is also erased, so before reformatting a card, any
data you want to keep should be copied to your personal computer’s hard
disk or other storage medium.
Caution regarding disposing/transferring the card (recovering data from
a reformatted card)
i If a card is reformatted or the data is erased from the card using the
camera or a computer, the card’s control data may be merely modified and
the data itself may not be completely erased from the card.
i In some cases it may be possible to recover the data from a reformatted
card using special software for that purpose. However, if the camera is
used to execute a full format, it will be impossible to recover the data even
by the use of data recovery software.
i If you are disposing of a card, it is recommended that you physically
destroy it. If you are transferring the card to someone else to use, it is
recommended that you use the camera’s full format function to reformat
the card, or use commercially available software for erasing card data.
Managing data is the responsibility of the user.
HINT
To cancel reformatting
i In step 5, select “EXIT”, and press the SET button.
English 116
RESETTING THE CAMERA SETTINGS
Reset the camera to the factory-preset settings.
1 Display the Option Menu (page 102).
2 Select “RESET SETTINGS” and press the SET button.
h The Reset Settings Menu appears.
YES:
Reset to the factory-preset settings.
NO:
Do not change the settings, and return to the Option Menu.
3 Select “YES”, and press the SET button.
h The camera settings are reset to the factory-preset settings.
HINT
i Note that the following settings do not change with this procedure:
Date and time setting
Language setting
TV system setting
File No. memory setting
117 English
CHECKING THE REMAINING INTERNAL
MEMORY AND CARD MEMORY
You can check the possible number of images, audio recording time and
video clip recording time remaining on the card. For a table showing the
maximum number of images and recording time for the internal memory and
for a specific card, please see “Possible Number of Images/Video Recording
Time/Audio Recording Time” on page 147.
1 Press the ON/OFF button to turn the
camera on.
<To check the remaining number of
still images>
Set the shooting mode to the single-
shot or sequential shots mode
(page 33).
<To check the remaining video clip
recording time>
Set the shooting mode to the video
clip recording mode (page 33).
h The remaining recording time is
shown on the monitor.
h The remaining number of images
and video recording time will differ
depending on the resolution and
video size settings.
143
00:06:05
Remaining number of images
Remaining recording time
<Still Image Shooting Screen>
<Video Clip Recording Screen>
English 118
For audio data
1 Set the camera to the audio
recording mode (page 71).
h The remaining audio recording time
is shown.
HINT
i When the remaining number of images or the remaining video recording
time is “0”, you cannot capture any more images. To capture more images,
either install a new card, or save the images to a computer and then erase
them (page 45) from the card.
i When the remaining number of images or the remaining video recording
time is “0”, it may be possible to capture a few more images by changing
the resolution setting or video clip mode setting (page 70).
i The maximum number of images is 9,999, and the maximum video/audio
recording time is 99:59:59. Note that if a large-capacity card is used, the
remaining number of images or recording time may not be correctly
displayed.
13:23:29
Remaining recording time
119 English
CHECKING THE REMAINING BATTERY CHARGE
When using the battery pack, the remaining battery pack charge can be
checked on the monitor. Make sure to check this indicator before capturing an
image. For an indication of the possible length of time for battery pack
operation, see page 146.
1 Press the ON/OFF button to turn the
camera on.
h The battery pack remaining charge
indicator appears in the lower right
corner of the monitor.
h Due to the battery pack
characteristics, when the ambient
temperature is low, may
appear early for an incorrect
indication of the remaining charge.
Also, depending on the conditions
of use of the camera or the ambient
conditions (temperature, etc.), the
indicated remaining charge may
change. Therefore, this indication
can only be used as a general
approximation of the remaining
charge.
Battery pack
remaining
charge indicator
Battery remaining charge
No indication, or
Approx. full.
( appears only in certain operation
modes.)
Power is low.
It will soon be impossible to capture or play
back images.
If this icon flashes when the shutter button
is pressed, images cannot be captured.
Recharge the battery pack.
134
Battery pack remaining
charge indicator
English 120
HINT
i If any data is present, you can also check the remaining battery pack
charge on the Information Screen (page 101).
i Battery life may differ even among battery packs of the same type.
i Depending on the usage of the camera (such as the number of times the
flash is used, etc.) or the ambient temperature (temperatures below 10°C
[50°F]) the number of images that can be saved on a fully charged battery
pack will vary greatly.
i It is recommended that you prepare an extra battery pack(s) when taking
pictures at a wedding or while traveling, for example, so you don’t miss
capturing images of important moments due to the battery pack power
running out. The same is recommended for taking photos in cold
environments. (In a ski area, for example, the battery pack can be kept
warm in your pocket until ready to use.)
121 English
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A TV
Connect the supplied AV interface cable from the USB/AV terminal on the
digital camera to the AUDIO and VIDEO input terminals on the TV.
Playback
i After connecting the digital camera to the television, set the TV input switch
to VIDEO input.
i When an AV interface cable is connected, no image appears on the
camera’s monitor.
i The playback method is the same as when viewing images on the
camera’s monitor.
i The same playback procedure as when playing back with the camera is
used to play back voice memos and audio recordings as well.
Voice memo playback: see page 39
Audio file playback: see page 72
CAUTION
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
Yellow plug
To the VIDEO input
terminal
White plug
To the AUDIO input
terminal
To the USB/AV terminal
Switch input to
VIDEO
Supplied dedicated AV
interface cable
English 122
DIRECT PRINTING
Your camera supports the PictBridge function. By connecting the camera
directly to a PictBridge-enabled printer, the camera’s monitor can be used to
select images and initiate printing (PictBridge printing).
Print preparations
1 Turn the printer on, use the supplied USB interface cable to connect
the camera to the printer.
h Connect the camera’s USB/AV terminal to the printer’s USB
connector.
h The USB Connection Screen appears on the camera’s monitor.
USB CONNECTION
CANCEL
PRINTER
COMPUTER
SELECTOK
Supplied dedicated
USB interface cable
To USB connector
on the printer
To the USB/AV terminal
123 English
DIRECT PRINTING
2 Select “PRINTER”, and press the
SET button.
h The screen to select the images to
print appears.
CAUTION
Caution when connecting a printer
i If the power to the printer is turned off while it is connected, the camera
may not operate correctly. If the camera does not operate correctly,
disconnect the USB interface cable, turn off the camera, and then
reconnect the cable.
i During PictBridge printing, the camera’s button operation response is
slower.
i If the camera is powered by the battery pack for printing, make sure that
the remaining battery charge is sufficient.
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
:
1
: 1
DATE
DATE
DATEPRINT
PRINT
PRINT
Print this image?
Print this image?
Print this image?
English 124
To select one image and print it (print selected image)
Procedure to select one still image and print it.
1 Complete the printing setup (page 122).
2 Press the [l] or [m] button.
h Display the image you wish to print.
:
1
: 1
DATE
DATE
DATEPRINT
PRINT
PRINT
Print this image?
Print this image?
Print this image?
125 English
DIRECT PRINTING
3 Specify the number of prints or
date-imprinted prints.
<Specifying the number of prints>
h Press the [n] or [o] button to
specify the number of prints.
h Press the [n] or [o] button until
the desired number of prints is
displayed.
<Specifying dated prints>
h Press [W] on the zoom switch to
add a check mark ( ) next to
.
4 Press the SET button.
h Printing begins.
HINT
To cancel printing
1 During printing, press the [o] button.
h The Confirm Cancel Printing Screen appears.
2 Select “YES”, and press the SET button.
h If “EXIT” is selected and the SET button is pressed, printing resumes.
CAUTION
i Do not specify dated prints for images that were captured with the date
imprint function (page 81) set to ON, or else the date will appear on the
photo print twice.
1
:
: 1
DATE
DATE
DATEPRINT
PRINT
PRINT
Print this image?
Print this image?
Print this image?
English 126
To print all the images (all images)
Print all of the images.
1 Complete the printing setup (page 122).
2 Press the MENU button.
h The PictBridge Menu appears.
3 Select “PRINT ALL IMAGES”, and
press the SET button.
h The Print All Images Screen
appears.
4 Specify the number of prints or
date-imprinted prints.
<Specifying the number of prints>
h Press the [n] or [o] button to
specify the number of prints.
h Press the [n] or [o] button until
the desired number of prints is
displayed.
<Specifying dated prints>
h Press [W] on the zoom switch to
add a check mark ( ) next to
.
5 Press the SET button.
h Printing begins.
CAUTION
Printing is not possible if there are more than 999 still images in the
card or internal memory
i Delete unwanted images before printing.
PictBridge MENU
PRINT 1 IMAGE
PRINT ALL IMAGES
DPOF
OK EXIT
1/1
1
DATE
DATE
DATEPRINT
PRINT
PRINT
:
: 1
Print all images?
Print all images?
Print all images?
127 English
DIRECT PRINTING
To print the images that are set to print (print reserved images)
Procedure to print all the images that are set to print.
1 Make the print settings (page 95), and complete the printing setup
(page 122).
2 Press the MENU button.
h The PictBridge Menu appears.
3 Select “DPOF”, and press the SET
button.
h The Print Scheduled Images
Screen appears.
h An image that is set to print
(page 95) is displayed.
4 Press the SET button.
h Printing begins.
h Printing begins about 1 minute after the SET button is pressed.
HINT
i In step 3, if you press the [l] or [m] button, you can confirm the images
that are set to print and their DPOF settings.
CAUTION
i Reserved images printing is not possible if a printer is used that does not
support your camera’s DPOF function.
i Multi-prints are not possible.
PictBridge MENU 1/1
PRINT 1 IMAGE
PRINT ALL IMAGES
DPOF
OK EXIT
PRINT
PRINT
PRINT
Print the DPOF images?
Print the DPOF images?
Print the DPOF images?
:
: 1
English 128
To change the printer settings and print images
(change printer settings)
Images are printed according to settings specified by the camera, such as
paper type, size, layout, printing quality, etc.
1 Complete the printing setup (page 122).
2 Press the MENU button.
h The PictBridge Menu appears.
3 Select the printer settings tab v,
and press the SET button.
h The Printer Settings Menu appears.
DATE STAMP:
Print the date the photo was taken.
MEDIA TYPE:
Specify the type of paper used for
printing.
PAPE R SI ZE:
Specify the size of paper used for
printing.
LAYOUT:
Specify how the images are to be
arranged on the paper.
QUALITY:
Select the print quality for the
images.
VALUES
VALUES
VALUES
VALUES
VALUES
DATE STAMP
MEDIA TYPE
PAPER SIZE
LAYOUT
QUALITY
PRINTER SETTINGS MENU
OK EXIT
1/1
Printer Settings tab
129 English
DIRECT PRINTING
4 Adjust the printer settings.
1 Use the arrow buttons to select a printer setting parameter, and
press the SET button.
h The screen to set the selected parameter appears.
2 Press the [n] or [o] button to adjust the setting, and press the
SET button.
h The selected parameter is set, and you are returned to the Printer
Settings Menu.
h Follow the same procedure to adjust the other parameters, as
desired.
h The contents of the settings that can be made for each parameter
will differ depending on the printer.
<When “V VALUES” is selected>
h The images will be printed according to the settings specified on the
printer side.
HINT
i The parameters that are displayed on the Printer Settings Menu will differ
depending on the printer that is connected.
i To use printer functions which do not appear on your camera’s Printer
Settings Menu, select “V VALUES.
i If a function set by the camera is not available in the printer, the camera’s
printer settings will automatically change to “V VALUE S.
English 130
APPENDICES
COMMONLY ASKED QUESTIONS
If you have a question about the camera operation, you might find the answer
in this compilation of commonly asked questions.
Question Answer Action
Power
Why doesn’t the
power turn on?
Due to cold
temperatures, the
battery pack
temporarily lost its
power.
Place the camera in
your pocket to warm
it up before using it.
Why is the battery
pack consumed
so quickly?
The ambient
temperature is
very low.
Keep the battery
pack in an
environment of 10 to
40°C (50 to 104°F).
The battery pack
life has expired.
Replace with a new
battery pack.
Why does the
icon
appear?
The remaining
battery pack
power is low.
Recharge the
battery pack.
Shooting
Why doesn’t the
touch sensor
work?
You are wearing
gloves.
Remove the glove
from the hand
pressing the shutter
button.
Why doesn’t the
flash operate?
The camera has
determined that
the image is bright
enough and the
flash is not
necessary.
Not a malfunction.
Capture the image;
the camera will
determine when the
flash is necessary.
131 English
COMMONLY ASKED QUESTIONS
Shooting
Are the settings
retained even
after the camera
is turned off?
All settings except
the self-timer and
the exposure
correction are
retained even after
the camera is turned
off.
Which resolution
setting should I
use?
Select the resolution
setting according to
the intended use:
kDzN:
Appropriate for
printing letter-size or
larger, and for
printing a close-up
of part of a photo
(trimming).
t: For printing
standard photo
(photo service)
sizes.
[: For photos
displayed on a web
page, or sent as
e-mail attachments.
What is the
difference
between the
digital zoom and
the optical zoom?
Because shooting
with the optical
zoom uses the
optics of a physical
lens, you can shoot
without losing
minute details in the
image. The digital
zoom, on the other
hand, works by
magnifying a portion
of the image that
hits the CCD sensor
and may produce a
coarser image.
Question Answer Action
English 132
Shooting
How can I get the
distant view into
focus?
Set the scene
function to the
landscape \
mode when
photographing.
Or, set the focus
range setting to
manual focus -,
and set the distance
to
.
Monitor
When used in
cold weather, why
does the image
seem to leave
traces as it
moves?
Condition due to
the liquid crystals.
Not a malfunction.
Spots that appear in
the monitor only
appear in the
monitor and will not
be recorded with the
images.
Why does the
displayed image
contain some red,
blue and green
dots, or why are
black spots
visible?
Question Answer Action
133 English
COMMONLY ASKED QUESTIONS
Viewing
images
Why is the image
too bright?
The subject was
too bright.
When capturing an
image, devise a way
to compensate for a
bright subject, for
example, by
changing the
shooting angle.
Why is the image
out of focus?
The focus is not
locked properly.
Hold the camera
correctly, and when
the image is locked
in focus, gently
press the shutter
button all the way to
capture the image.
Why doesn’t the
zoom jump
playback work?
Zoom jump
playback does not
work for an image
that was created
from a magnified
portion of a zoom
jump image, or for
video clips.
Not a malfunction.
Why is there no
image (z is
shown)?
This may happen
when trying to
play back images
stored on a card
from a different
digital camera.
Play back images
that were recorded
on a card using this
camera.
Why do vertical
stripes appear?
If a bright subject
is shot in the
video clip
recording mode,
vertical stripes
may appear on
the monitor or in
the image.
Not a malfunction.
Question Answer Action
English 134
Viewing
images
Why isn’t the
magnified image
clear?
Due to the
characteristics of
the camera,
magnified images
appear less clear.
Not a malfunction.
Why isn’t the
captured image
clear?
The image was
captured using
the digital zoom.
Not a malfunction.
Zoom in only within
the optical zoom
range when
shooting.
Can I play back
image data that I
edited using my
computer?
We cannot
guarantee the
accurate playback of
data that has been
edited using a
computer.
Printing
Why does a
message appear
during PictBridge
printing?
There is a
problem with the
printer.
Please refer to the
instruction manual
for your printer.
Misc.
Why does the
“Card full” or
“Internal memory
full” message
appear?
There is no more
available memory
on the card or in
the camera’s
internal memory.
Delete unnecessary
data, or use a card
that has more
memory available.
Why does the
“Card is protected”
message appear?
The lock switch on
the card is in the
locked (protect)
position.
Move the lock switch
to the unlocked
position.
Question Answer Action
135 English
COMMONLY ASKED QUESTIONS
Misc.
Why can’t the
camera be
operated?
A temporary
internal circuitry
problem may be
the cause.
Remove the battery
pack from the
camera, wait a few
minutes, then
reinstall the battery
pack and try again.
Can I use my
camera abroad?
If you have
questions about
using the power
cord abroad, please
consult with a dealer
near you for advice.
Why does the
“System error”
message appear?
A problem has
occurred within
the camera or
card.
Check the following
items:
1 Remove the
card and then
install it again.
2 Remove the
battery pack and
then install them
again.
3 Install a different
card.
If “System error” still
appears after
performing the
above steps, then
take the camera to
the dealer for
service.
Question Answer Action
English 136
TROUBLESHOOTING
Before taking your camera to the repair shop, check the following table for a
possible solution to the problem.
CAMERA
Problem Cause Action
Reference
page
Power
No power. The battery
pack is dead.
Recharge the
battery pack.
17
The battery
pack has not
been inserted
correctly.
Reinsert the
battery pack,
making sure to
orient it
correctly.
21
The battery/
card
compartment
cover is not
completely
closed.
Close the
battery/card
compartment
cover
completely.
The camera
turns off by
itself.
The power
save function
is operating.
Not a
malfunction. 24
Shooting
An image is
not captured
when the
shutter button
is pressed.
The power is
not turned on.
If the auto
power off
function was
activated, turn
the camera on
before
shooting.
If the camera
was turned off,
press the ON/
OFF button to
turn it on.
24
137 English
TROUBLESHOOTING
Shooting
An image is
not captured
when the
shutter button
is pressed.
The maximum
number of
images that
can be
captured or the
maximum
video clip
recording time
has been
reached.
Install a new
card.
21
Delete the
images that are
not necessary.
Save the
images to
separate media,
then delete all
the images from
the card.
45, viii
The operation
buttons (arrow
buttons,
MENU button,
etc.) do not
work.
A finger is
touching the
shutter button,
and the focus
lock is active.
Remove your
finger from the
shutter button,
and then use
the operation
buttons.
The flash does
not operate.
The flash off
mode is
selected.
Set the flash to
automatic flash
mode or forced
flash mode.
59
The battery
pack is dead.
Recharge the
battery pack.
17
The “Battery
depleted”
message
appears.
The battery
pack is
consumed.
Recharge the
battery pack.
17
Problem Cause Action
Reference
page
English 138
Shooting
When zooming
in or out, the
zoom
movement
stops
momentarily.
The optical
zoom has
moved to the
maximum
magnification
position.
Not a
malfunction.
Release the
zoom switch,
and press it
again.
58
There is noise
in the captured
image.
The ISO
sensitivity
setting is too
high.
Set the ISO
sensitivity to a
lower setting.
77
When
recording a
video clip
under
fluorescent
lights, a
noticeable
flicker appears
in the image.
This occurs
when the
shutter speed
is too fast.
Set the ISO
sensitivity to
w or less.
77
Monitor
No playback
image
appears.
The playback
mode is not
active.
Press the
playback button
[=].
32
Viewing
images
The image is
too dark.
The flash was
blocked by a
finger or other
object.
Hold the
camera
correctly, and
make sure the
flash is not
obstructed.
28
The subject
was too far
away.
Capture the
image in the
range of
operation of the
flash.
145
Problem Cause Action
Reference
page
139 English
TROUBLESHOOTING
Viewing
images
The image is
too dark.
The subject
was lit from
behind.
Use the forced
flash mode.
59
Use the
exposure
correction
function.
80
There is not
enough light.
Adjust the ISO
sensitivity
setting.
77
The image is
too bright.
The forced
flash mode is
selected.
Select a
different flash
mode.
59
The subject
was too bright.
Use the
exposure
correction
function.
80
The ISO
sensitivity
setting is
incorrect.
Set the ISO
sensitivity to
t.
77
The image is
not in focus.
The subject is
too close to the
camera.
Select the
correct focus
setting for your
needs.
37, 63
The focus
setting is not
correct.
The camera
moved when
the shutter
button was
pressed.
Hold the
camera
correctly and
press the
shutter button
correctly.
28, 37
The focus is
not locked
properly.
The lens is
dirty.
Clean the lens.
Problem Cause Action
Reference
page
English 140
Viewing
images
The colors of
the images
captured
indoors are not
correct.
This is due to
ambient
lighting.
Capture the
image using
the forced flash
mode.
59
The white
balance setting
is incorrect.
Set the white
balance setting
correctly.
79
A part of the
image is
missing.
The handstrap
or a finger was
blocking the
lens.
Hold the camera
correctly, and
make sure the
lens is not
obstructed.
28
“No image” is
shown.
There is no
image stored in
the installed
card or the
internal memory.
Play back after
capturing
images.
Image
editing
You cannot
edit or rotate
an image.
The protect
mode is set.
Cancel the
protect mode. 84
Misc.
The “Image is
protected”
message
appears and
the data cannot
be deleted.
You have
attempted to
delete data
that is
protected from
accidental
erasure.
Cancel the
protect mode.
84
The recording
capacity is less
than that
indicated in the
section
“Possible
Number of
Images/Video
Recording
Time/Audio
Recording
Time”.
The recording
capacity is less
than the value
specified for
the card.
Depending on
the card, the
capacity may
be less than
the specified
value. Please
refer to the
instructions
that
accompanied
the card.
147
Problem Cause Action
Reference
page
141 English
TROUBLESHOOTING
Notes regarding the scene function
Y
The macro + focus range setting is not available.
G
The pan o, macro + and manual focus - focus
range settings are not available.
The AF seeker p focus mode setting is not available.
The digital zoom is not available.
_
The resolution cannot be set to F or more.
The flash is disabled even when shooting single shots.
\
The macro + focus range setting is not available.
]
H
The macro + and manual focus - focus range
settings are not available.
The flash is disabled even when shooting single shots.
The AF seeker p focus mode setting is not available.
r
The pan o, macro + and manual focus - focus
range settings are not available.
The AF seeker p focus mode setting is not available.
The digital zoom is not available.
English 142
SPECIFICATIONS
Camera
Type CCD digital camera (recording and playback)
Image file format Still images: JPEG format (DCF, DPOF, Exif
2.21 compliant)
Note: Designed mainly by the Japan
Electronics and Information Technology
Industries Association (JEITA), DCF
(Design rule for Camera File system) is
standard for digital still camera image
files to provide interoperability between
digital photography devices for the
images stored on removable memory
cards. However, it is not guaranteed that
all devices will support the DCF standard.
Video clips:QuickTime Movie (Photo-JPEG)
Audio recordings:WAVE format (monaural)
Data storage media Internal memory: Approx. 52 MB
External memory: SD Memory Card
(equivalent to a 8 GB SDHC Memory Card)
Camera effective number
of pixels
Approx. 10 million pixels
Image sensor 1/2.3-inch (1.1 cm) CCD
Virtual number of pixels: Approx. 10.34 million
pixels, interlace scan, primary color filter
143 English
SPECIFICATIONS
Recording resolution <Still image shooting>
k: 3648 × 2736 pixels
N: 3648 × 2056 pixels
D: 2816 × 2112 pixels
z: 2288 × 1712 pixels
t: 1600 × 1200 pixels
[: 640 × 480 pixels
<Video clip recording>
d: 640 × 480 pixels, 30 frames/second
5: 320 × 240 pixels, 15 frames/second
White balance Full-auto TTL, manual setting possible
Lens 5.0× optical
zoom lens
f=6.3 mm to 31.5 mm
(35 mm film camera
conversion: 36 mm to
180 mm)
Autofocus, 6 groups,
8 elements (4 with aspheric
surfaces)
Aperture Open F=3.5 (Wide) to 5.6 (Tele)
Exposure control type Programmable AE
Exposure correction available from the
Shooting Menu (0±1.8EV in 0.3EV steps)
Light-measuring modes Multi-section measuring, center-weighted
measuring, spot measuring
English 144
Range Normal photography: 40 cm (15.75 in.) to
(Wide), 90 cm (2.95 ft.) to
(Tele)
Macro photography: 10 cm (3.94 in.) to 50 cm
(19.69 in.) (Wide), 60 cm (23.62 in.) to 1 m
(3.28 ft.) (Tele)
Digital zoom For shooting: 1× to 4×
For playback: 1× to 57× (varies with resolution)
Shutter speed Single-shot mode: 1 to 1/2,000 sec.
(Maximum approx. 2 seconds when the
scene function is set to fireworks Hetc.)
(During flash: 1/30 to 1/2,000 sec.)
Sequential shots mode:
1/2 to 1/2,000 sec.
Video clip recording mode:
1/30 to 1/10,000 sec.
Sensitivity (standard
output sensitivity)
Single-shot mode/sequential shots mode
(standard output sensitivity):
Auto (ISO50 to 400)/ISO50, ISO100,
ISO200, ISO400, ISO800, ISO1600, and
ISO2500 (switchable from Shooting Menu)
Video clip recording mode:
Auto (ISO450 to 3600)/ISO450, ISO900,
ISO1800, ISO3600 and ISO7200
(switchable from Shooting Menu)
* Sensitivity measured in compliance with
the ISO standard (ISO 12232:2006).
Monitor 2.5-inch (6.4 cm) TFT color LCD
Approx. 230,000 pixels
(Frame coverage: Approx. 100%)
Brightness adjustment: 5-step
145 English
SPECIFICATIONS
Flash working range GN = 5.5
Approx. 40 cm (15.75 in.) to 2.9 m (9.51 ft.)
(Wide)
Approx. 60 cm (23.62 in.) to 1.8 m (5.91 ft.)
(Tele)
Flash modes Auto-flash, forced flash, flash off, red-eye
reduction
Focus TTL-type AF (9-point range finder/spot focus/
AF seeker), manual focus (14 steps)
Self-timer Approx. 2-second delay, 10-second delay
Ambient
environment
Temperature
0 to 40°C (32 to 104°F) (operation),
–20 to 60°C (–4 to 140°F) (storage)
Humidity 30 to 90% (operating, no condensation)
10 to 90% (storage, no condensation)
Power supply Lithium-ion battery pack (DB-L70) × 1
Dimensions (at narrowest
part, not including grip or
lens protrusion)
94.2 (W) × 56.4 (H) × 23.4 (D) mm
3.71" (W) × 2.22" (H) × 0.92" (D)
Weight Approx. 118 g (4.16 oz.) (without battery pack
and card)
English 146
Camera connectors
Battery life
i Until battery pack runs out when using a fully charged battery pack at a
25°C (77°F) ambient temperature.
i The operation time may vary depending on the conditions of the battery
pack and the conditions of use. Especially when used at temperatures
below 10°C (50°F), the battery pack operation time is drastically reduced.
USB/AV
(communication/audio
and video output)
terminal
Dedicated regrouped jack
Audio
output
590 mVrms (–2.4 dBs), 2.2 k or less,
monaural
Video
output
1.0 Vp-p, 75 unbalanced, sync
negative, composite video, NTSC
color TV system/PAL TV system
(switchable from the Option Menu)
USB USB 2.0 Full Speed
PC camera: USB video class
Maximum recording time 220 images:
CIPA standard (when a Toshiba 128 MB
SD Memory Card is used)
Maximum playback time 260 minutes:
LCD monitor on, continuous playback
147 English
SPECIFICATIONS
Possible Number of Images/Video Recording
Time/Audio Recording Time
The table shows the possible number of captured images and the possible
recording time for the camera’s internal memory and for the commercially
available 2 GB and 8 GB SD Memory Cards.
i Up to 9 hours of continuous audio recording is possible.
i When recording a video clip using an 8 GB card, recording terminates
when the size of the file currently being recorded reaches approx. 4 GB.
i The values were determined using an SD Memory Card by Sandisk.
i Even with cards of the same capacity, the amount of data that can actually
be stored may differ depending on the card brand, etc.
i The continuous shooting time for each video clip will differ depending, for
example, on the card capacity, environmental conditions (temperature and
shooting conditions, etc.).
Shooting
mode
setting
Resolution
setting
Compression
rate setting
Internal
memory
SD Memory Card
2GB 8GB
Single-shot
mode/
Sequential
shots mode
k
j
15 images 585 images 2,340 images
0
23 images 861 images 3,450 images
N
j
20 images 775 images 3,110 images
0
30 images 1,140 images 4,610 images
D
j
26 images 984 images 3,950 images
0
38 images 1,440 images 5,790 images
z
j
39 images 1,470 images 5,920 images
0
58 images 2,130 images 8,580 images
t
j
79 images 2,950 images 11,800 images
0
114 images 4,130 images 16,500 images
[
j
416 images 15,490 images 61,900 images
0
555 images 20,600 images 82,500 images
Video clip
recording
mode
d
36 sec.
22 min. 28 sec. 1 hr. 30 min.
5
2min. 46sec.
1 hr. 43 min.
6 hr. 55 min.
Audio file
mode
——
1 hr. 50 min.
68 hr. 54 min. 275 hr.
English 148
Supplied battery pack charger
i The VPC-E10GX model is supplied with a power cord that is appropriate
for the region of destination.
i When using the supplied battery pack charger abroad, the power cord may
need to be replaced in accordance with local requirements. Please contact
your local dealer for details.
Supplied Li-ion battery pack
Part No. VAR-L70
Power source AC 100 to 240 V, 50 to 60 Hz, 2.6 W
Rated output DC 4.2 V, 330 mA
Compatible batteries Supplied or separately sold Lithium-ion
battery pack (DB-L70)
Ambient
environment
Temperature
0 to 40°C (32 to 104°F) (recharge),
–20 to 60°C (–4 to 140°F) (storage)
Humidity 20 to 80% (no condensation)
Dimensions
62 (W) × 23.8 (H) × 90 (D) mm
2.44" (W) × 0.94" (H) × 3.54" (D)
Weight (without power cord) Approx. 65 g (2.29 oz.)
Power cord
rated value
VPC-E10 AC 125 V, 7 A
VPC-E10EX AC 250 V, 2.5 A
Part No. DB-L70
Voltage 3.7 V
Rated output 680 mAh
Ambient
environment
Temperature 0 to 40°C (32 to 104°F) (during use,
recharged)
10to30°C (14to86°F) (storage)
Humidity 10 to 90% (no condensation)
Dimensions 26.9 (W) × 7.5 (H) × 38 (D) mm
1.06 (W) × 0.30 (H) × 1.50 (D) in.
Weight Approx. 15 g (0.53 oz.)
149 English
SPECIFICATIONS
Others
Mac OS and QuickTime are trademarks of Apple Inc., registered in the U.S.
and other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in
the USA and other countries.
Intel and Pentium are registered trademarks of Intel Corporation (USA).
In this manual, the Microsoft
®
Windows
®
2000 operating system, Microsoft
®
Windows
®
XP operating system, and Microsoft
®
Windows
®
Vista operating
system are collectively referred to as “Windows”.
Software Red Eye by FotoNation
TM
2003-2005 is a trademark of FotoNation
®
Inc.
Red Eye software
©
2003-2005 FotoNation In Camera Red Eye - covered by
U.S. Patent No. 6,407,777. Other patents Pending.
SDHC is a trademark.
All other company and product names are registered trademarks or
trademarks of their respective owners.
CAUTION
i It is forbidden to copy this manual, whole or in part, without prior written
permission.
i All images and illustrations given in this manual are for explanation
purposes and may differ slightly from that of the actual product. Also,
actual specifications are subject to change without prior notice and
therefore may differ from the contents of this manual.
English 150
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i Sanyo Electric shall not be held responsible for any problems resulting
from the use of this camera.
i Sanyo Electric declines all responsibility for damages due to improper use
of the camera, failure to adhere to the instructions given in this manual, or
repairs or changes done by those other than a technician authorized by the
manufacturer.
i Sanyo Electric shall not be held responsible for any damage caused by
optional devices or consumable items used with the camera other than
those supplied with the camera or those specified by Sanyo Electric.
i Sanyo Electric shall not be held responsible for any losses or loss of
revenue resulting from the loss of data caused by the malfunction, or the
repairing of a malfunction, of the camera.
i The images captured with this camera will differ in quality from pictures
taken with a standard film camera.
151 English
HINTS FOR TAKING PICTURES
Taking great pictures in difficult surroundings is easier than you might think.
By keeping a few points in mind and choosing the correct settings, you can
create photos that you’ll be proud to display and share.
Basic photography
If images are blurred even when the autofocus is used
Your camera employs an autofocus function. When you snap a picture using
the autofocus, the camera automatically adjusts the settings so that the
image will be in focus. If you are getting blurred images even when using the
autofocus, one or more of the following might be the reason.
k How the autofocus works
The autofocus is activated when the shutter button is lightly touched. Press
the shutter button slightly, and the target mark will appear on the monitor to
indicate that the autofocus has been activated. Next, continue to gently press
the shutter button all the way to snap the picture. This two-step method is the
way to ensure that your photos are perfectly focused.
k Reasons for unfocused images
1 The shutter button was pressed before the image was focused.
2 After the image was focused, the subject moved.
h Even if camera focuses the subject once, if the distance between the
camera and the subject is changed, the subject may become out of
focus.
3 The focus setting is not set for the correct distance.
h If you shoot a close-up subject with the camera set to the normal focus
mode, or if you shoot a subject at normal distance with the camera set
to the macro (close-up) mode (page 63), the image will not be in focus.
k Preventing blurred images
1 Confirm that the camera is set to the correct focus mode for your subject.
2 Hold the camera correctly, and lightly touch the shutter button.
3 Wait for the target mark to appear in the monitor, and holding the camera
steady, gently continue to press the shutter button all the way down.
Following these steps for a gentle but firm pressing of the shutter button will
ensure that you get beautifully focused photos.
English 152
Photographing a moving subject
Situation: You would like to snap an action shot of a moving child or pet. The
autofocus is activated, but because the subject is moving, the image may be
blurred. In particular, when the distance between the camera and the subject
is changing, it is difficult to lock the focus on the subject. Here are some hints
for successfully capturing images of moving subjects.
k Reasons for unfocused images
When the shutter button is touched lightly, the camera’s autofocus works by
determining the distance between the camera and the subject. Once the
subject is in focus, if it then moves before the picture is snapped, the image
may be out of focus. This often happens when you once lock the focus on a
subject and then wait for the right moment to snap the picture. And,
conversely, a blurred image may result if you press the shutter button all the
way in one step in an attempt to quickly capture an action scene, thus failing
to activate the autofocus in time.
k Preventing blurred images (How to use the manual focus [page 65])
In addition to the autofocus, a manual focus mode is also incorporated in your
camera. In the autofocus mode, the distance between the camera and the
subject is automatically determined when you press the shutter button
halfway. In contrast to this, with the manual focus mode, you manually set the
focus by specifying the correct distance between the camera and the subject
before taking the picture.
k How to photograph a moving subject
1 Set the camera’s focus mode to the manual focus. Set the focus distance
to the correct distance between the camera and the subject.
2 When the subject is at the set focus distance, gently press the shutter
button all the way down.
<Advantage of using the manual focus>
i Images can be quickly captured without waiting for the autofocus to
activate.
i Because you are presetting the focus distance, the focus can be more
accurate.
<Using the manual focus effectively>
i When photographing a moving subject, press the shutter button just before
the subject reaches the focus distance, and the shutter will be released
when the subject is at the correct distance.
i Use manual focus to avoid incorrectly focused images when there is an
object between the camera and the subject you wish to focus on.
153 English
HINTS FOR TAKING PICTURES
Shooting with the scene function
Shooting portraits (portrait mode Z)
Points:
i Choose a background that doesn’t detract from your subject.
i Move in close to your subject.
i Pay attention to lighting and how it affects your subject.
NOTE
i If the background is distracting, it will not show your subject to his best
advantage. Move in closer to your subject or zoom in so that the
background does not compete with the subject.
i In portrait photography your subject is clearly the central figure, so try
techniques that allow the subject to stand out.
i If light is coming from behind your subject (backlit), his face will appear
dark. You can get a better picture by using the flash, for example, or
changing the exposure setting.
Photographing moving subjects (sports mode Y)
Points:
i Match the camera’s movement with that of the subject.
i Set the zoom to the Wide end (wide-angle).
i Don’t be too hesitant to press the shutter button, or you’ll miss the action.
NOTE
i Tips to not missing those great action shots: Make sure you’re holding the
camera correctly. Keep the subject in the lens at all times, moving the
camera with him while waiting for the right shot. Move your whole body–not
just your arms–with the camera while shooting.
i Blurred images are more likely when the zoom is set to the Tele end than
the Wide end. Set the zoom as close as possible to the Wide end.
i Learn to press the shutter button quickly yet smoothly the instant your
photo chance occurs.
English 154
Night photography (night view portrait mode ])
Points:
i Avoid camera shake.
i Increase the ISO sensitivity.
NOTE
i Camera shutter speed during night photography is considerable slower, so
there is a much greater chance that your photographed images will be
blurry. Use a tripod whenever possible, or if a tripod is not available, you
can lean against a wall or pillar to help stabilize the camera.
i You can photograph your subject with the night scene in the background by
using the flash. Be careful not to shoot too close to the subject, however, or
your subject’s face will appear too bright.
i After the flash operates, keep the camera and the subjects motionless for
about 2 seconds.
Photographing scenery (landscape mode \)
Points:
i Shoot using a high resolution.
i For zoom photography, use the optical zoom.
i Pay attention to picture composition.
NOTE
i When shooting with a wide-angle setting, or if you intend to enlarge the
photo, the higher the resolution, the better.
i To zoom in on distant scenery, it’s better to use the optical zoom. Using the
digital zoom produces a coarser image. Hold the camera securely, keeping
your elbows close to your body and making sure the camera is stable.
Using a tripod or other means of stabilizing the camera will increase the
likelihood of getting a clear photo.
i Don’t forget to pay attention to picture composition; note perspective and
be aware of how the placement of objects affects the scene.
SANYO Electric Co., Ltd.
147


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo VPC-E10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo VPC-E10 in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info