481752
10
Zoom out
Zoom in
Previous page
1/24
Next page
10
OI-201-10EG
Remote Control Unit (continued)
Program button For details, see “Setting the Timer”.
Press this button to select the mode you want to program.
TIMER SELECT button No display : The timer does not operate.
: The air conditioner stops at the set time.
: The air conditioner starts at the set time.
: The air conditioner stops and starts, or starts and stops, at the
set times every day.
MODE selector button Use this button to select the COOL or FAN mode.
(COOL)
: The air conditioner makes the room cooler.
(FAN) : The air conditioner works only as a circulation fan.
FLAP button Press this button to select the sweep function, which moves the flap up and
down automatically.
: The flap moves up and down automatically.
FAN SPEED selector button
: The air conditioner automatically decides the fan speeds.
: High fan speed
: Medium fan speed
: Low fan speed
1 HR. TIMER button : When you press this button, regardless of whether the unit is
(1-HOUR OFF TIMER) operating or stopping, the unit operates for one hour and then
shuts down.
ACL button (ALL CLEAR) Puts the remote control unit into pre-operation status. Always press this
button after replacing the batteries.
ADDRESS switch
Change the address switch to prevent mixing of signals from remote control
units when two Sanyo air conditioners are installed next to each other.
Normally, the remote control address switch is set to A. For the second
indoor unit, both addresses of the remote control unit and the indoor unit
must be changed. The second remote control unit address must be changed
to B by breaking off the tab ”A. And the second indoor unit address must
be changed from 1-OFF, 2-OFF to 1-ON, 2-ON by switching the dip switch in
the indoor unit. For more information, please contact the dealer where you
made the purchase.
Normally, the tabs on the remote control unit should not be bent.
SENSOR button When you press this button (use a small-tipped object such as a ballpoint
pen), the mark will appear at the display. And the room temperature is
detected by the sensor which is built into the indoor unit and the air
conditioner is controlled accordingly.
NOTE If the remote control is located near a heat source, such as a space heater or
in direct sunlight, press the SENSOR button to switch to the sensor on the
indoor unit.
NOTE The remote control unit sends the temperature signal to the air conditioner regularly at five minute intervals.
If the signal from the remote control unit stops for more than ten minutes due to the loss of the remote
control unit or other trouble, the air conditioner will switch to the temperature sensor which is built into
the indoor unit and control the room temperature. In these cases, the temperature around the remote
control unit may differ from the temperature detected at the air conditioners position.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo TS2432 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo TS2432 in the language / languages: English as an attachment in your email.

The manual is 3,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info