481744
6
Zoom out
Zoom in
Previous page
1/10
Next page
English
1HR.
TIMER
ON/OFF
operation
ACL
(Reset)
QUIET
button
button
button
button
LED CLEAN lamp
TIMER lamp
OPERATION lamp
Fig. 59a-1
Fig. 59b-1
Fig. 59c-1
LED CLEAN lamp
TIMER lamp
OPERATION lamp
Fig. 59c-2
(SAP-KMRV76, KMRV96, KMRV126)
(SAP-KRV186, KRV246)
(SAP-KRV96)
21
For indoor unit type
(SAP-KMRV76EH, KMRV96EH, KMRV126EH)
(SAP-KRV96EHDS)
(SAP-KRV186EH, KRV246EH)
After turning on the power of the air conditioner, use the remote
controller and follow the steps below to conduct the test run.
(1) Set the remote controller in Test Run mode. (Fig. 59a-1)
a)Press and hold the QUIET button and the 1HR. TIMER button.
b)Then press and hold the ACL (Reset) button with a pointed
object such as the tip of a pen. After 5 seconds, release the
ACL button first.
c)Then release the QUIET and 1HR. TIMER buttons.
d) appears and “oP-1” blinking in the remote controller clock
display area. (Fig. 59b-1)
(2) Start Cooling mode test run by pressing the ON/OFF operation
button of the remote controller. (Fig. 59a-1)
This starts the fan producing uncooled forced air with the 3 indi-
cator lamps (OPERATION lamp, TIMER lamp, and LED CLEAN
lamp) on the main unit blinking. (Fig. 59c-1 or 59c-2)
After 3 minutes, the system shifts into cooling operation, and
cool air will start to be felt. Cooling mode test run is unaffected
by the room temperature.
(3) Press the ON/OFF operation button of the remote controller again
to stop the test run. (Fig. 59a-1)
(4) Finally press the ACL (Reset) button of the remote controller to
release it from Test Run mode to return to normal mode.
(Fig. 59a-1)
” and “oP-1” will disappear from the remote controller clock
display area.
After the test run is completed, be sure to press the ACL (Reset)
button to return to normal mode. The air conditioner will not operate
correctly if this is not done.
IMPORTANT
08-080 CMRV3146EH_IU ENG 2/15/08 6:53 PM Page 21
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo SAP- KMRV96 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo SAP- KMRV96 in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info