598876
117
Zoom out
Zoom in
Previous page
1/228
Next page
Kapitel 4Einstellungen — Menü [ANZEIGE OPTION]
DEUTSCH - 117
[SDI IN]
(Nur für PT-DZ21K2, PT-DS20K2, PT-DZ16K2)
Stellen Sie diese Funktion in Übereinstimmung mit dem Signaleingang am Anschluss <SDI IN 1>/<SDI IN 2>
(PT-DZ21K2, PT-DS20K2) oder am Anschluss <SDI IN> (PT-DZ16K2) ein.
Einstellen von [SDI-VERBINDUNG]
(Nur für PT-DZ21K2, PT-DS20K2)
1) Drücken Sie as, um [SDI IN] auszuwählen.
2) Drücken Sie die <ENTER>-Taste.
fDer Bildschirm [SDI IN] wird angezeigt.
3) Drücken Sie as, um [SDI-VERBINDUNG] auszuwählen.
4) Drücken Sie qw, um das Element umzuschalten.
[SINGLE LINK] Stellt den SDI1-Eingang und den SDI2-Eingang auf Single-Link ein.
[DUAL LINK] Stellt den SDI1-Eingang und den SDI2-Eingang auf Dual Link ein.
[AUTO] Wählt automatisch Single-Link oder Dual Link aus.
Hinweis
f[SDI-VERBINDUNG] kann nicht eingestellt werden, wenn [MODUS BACKUP-EINGANG] auf [2] eingestellt ist.
fWenn [AUTO] eingestellt ist, werden entweder Single-Link oder Dual Link automatisch ausgewählt, indem die Payload-ID des
Eingangssignals ausgelesen wird. Single-Link wird ausgewählt, wenn das Eingangssignal keine Payload-ID besitzt.
Einstellen von [SIGNALPEGEL]
Wählen Sie die Amplitude des Signals, das eingegeben werden soll.
1) Drücken Sie as, um [SDI IN] auszuwählen.
2) Drücken Sie die <ENTER>-Taste.
fDer Bildschirm [SDI IN] wird angezeigt.
3) Drücken Sie as, um [SIGNALPEGEL] auszuwählen.
4) Drücken Sie qw, um das Element zu ändern.
[64-940] Diese Einstellung sollte normalerweise verwendet werden.
[4-1019] Wählen Sie dieses Element aus, wenn Grau als Schwarz angezeigt wird.
Einstellen von [FARBTIEFE]
1) Drücken Sie as, um [SDI IN] auszuwählen.
2) Drücken Sie die <ENTER>-Taste.
fDer Bildschirm [SDI IN] wird angezeigt.
3) Drücken Sie as, um [FARBTIEFE] auszuwählen.
4) Drücken Sie qw, um das Element zu ändern.
[AUTO] [12-bit] oder [10-bit] wird automatisch ausgewählt.
[12-bit] Auf [12-bit] festgelegt.
[10-bit] Auf [10-bit] festgelegt.
Einstellen von [3G-SDI ABBILDUNG]
1) Drücken Sie as, um [SDI IN] auszuwählen.
2) Drücken Sie die <ENTER>-Taste.
fDer Bildschirm [SDI IN] wird angezeigt.
117


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PT-DS20K2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PT-DS20K2 in the language / languages: German as an attachment in your email.

The manual is 21,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info