489698
41
Zoom out
Zoom in
Previous page
1/60
Next page
41
Two different remote control codes are assigned to this projector:
the factory-set code (Code 1) and the secondary code (Code 2).
This switching function prevents interference from other remote
controls when several projectors or video equipment next to each
other are used at the same time.
When operating the projector in Code 2, the code for both the
projector and the remote control must be switched to Code 2.
To change the code of the projector:
Press the Point 8 or OK buttons to switch between Code 1 and
Code 2.
To change the code of the remote control:
Press and hold both the MENU and IMAGE ADJ. button on the
remote control for more than 5 seconds to switch between Code
1 and Code 2.
After changing the code, make sure the remote control operates
properly.
Remote control
Shutter demo
Press the Point 8 or OK buttons to start Shutter demo. The
automatic slide shutter closes once with the lamp being turned on
and opens up again. This is used for checking the operation of the
automatic slide shutter.
Note:
•Whenthebatteriesoftheremotecontrolarereplaced,theremote
controlcodeautomaticallyreturnstotheinitialcode(Code1).
Shutter demo
Remote control
For reducing power consumption as well as maintaining the lamp
life, the Power management function turns off the projection lamp
when the projector is not used for a certain period.
When this function is On” and if the input signal is interrupted
and no button is pressed for more than 30 seconds, the timer
display with “No signal” appears on the screen. It starts the
countdown until the lamp is turned off. The countdown time is set
to five (5) minutes.
When the countdown time has elapsed, the lamp is turned off to
cool itself down. The POWER indicator is blinking red during the
cooling-off period. When the lamp has been fully cooled down,
the POWER indicator changes to green blinking. In this condition,
the projection lamp can be turned on when the input signal is
reconnected or any button on the top control or remote control is
pressed.
Press the Point
8 or OK buttons to switch On/Off.
Power management
The time left until
lamp off
Power management
Note:
•TheShutterdemofunctioncannotbeoperatedcontinuously.
Onceyoustarted,itcannotbeselectedagainforaboutfive
seconds.
Setting
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PLV-Z700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PLV-Z700 in the language / languages: English as an attachment in your email.

The manual is 5,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PLV-Z700

Sanyo PLV-Z700 User Manual - German - 60 pages

Sanyo PLV-Z700 User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info