489694

Sanyo PLC-ZM5000L Manual

74
Zoom out
Zoom in
Previous page
1/92
Next page
appears on the screen
–
Filter is out of scroll. Replace the filter cartridge with a new one promptly. (See
pages 67-68)
The image is out of
focus.
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
Note: Movingtheprojectorfromacooltemperaturelocationtoawarmtemperature
locationmayresultinmoisturecondensationonProjectionLens.Insuch
cases,leavetheprojectorOFFandwaituntilcondensationevaporates.
– Projecting from excessive slant angle to the screen may cause keystone distortion
and partial imperfect focus.
The image is not
bright enough.
– Check if Contrast or Brightness is adjusted properly. (See pages 41, 47)
– Check if Image level is selected properly. (See pages 40, 46)
– Check the Lamp control function. ( See “Setting” section on page 57)
– Check the LAMP REPLACE indicator. If it lights, the end of lamp life is approaching.
Replace the lamp with a new one promptly. (See page 69)
The color is strange.
– Check the Input signal, color system, video system, or computer system mode.
– Adjust the Image Level properly. (See pages 40, 46)
The image is Left/
Right reversed.
– Check the Ceiling / Rear function. (See pages 44, 50)
The image is Top/
Bottom reversed.
– Check the Ceiling function. (See pages 44, 50)
The image is distorted
or runs off.
– Check PC adjust Menu or Screen Menu and adjust them.
Auto PC adjustment
function does not
work.
– Check the Input signal. Auto PC Adjustment function cannot work when 480p, 575p,
720p, 480i, 575i, 1035i, 1080i or 1080p is selected or when the digital signal is input
into HDMI or DVI-D terminal. See page 37.
Some displays are
not seen during the
operation.
– Check the Display function. (see page 52)
The setting does not
remain after turning
off power.
– Make sure you selected Store after adjusting settings. Some settings cannot be
stored if not registered with Store function.
Power management
function does not
work.
– Power management function cannot work while Freeze function is running or the
shutter is closed.
Image disappears
automatically.
– Check the power management function in the Setting. The power management is set
to On at the factory.
Capture function does
not work.
– Check the connection to see if there is signal.
– Capture function is not available when the Picture in Picture function is set to
User1-5.
Some menus cannot
be selected.
– Each of the Video Input and Computer Input has a limit on selectable menus.
No sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. ( See page 28)
– Press the Mute button. (See page 28)
– Is the image projected? You will hear the sound only when the image is projected.
– Check the Build-in SP function. (See page 28)
Appendix
74
… 74 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PLC-ZM5000L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PLC-ZM5000L in the language / languages: English as an attachment in your email.

The manual is 13,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info