215978
53
Zoom out
Zoom in
Previous page
1/79
Next page
53
Remote control
This function allows you to change brightness of the
screen.
Normal ...... Normal brightness
Eco ............ Lower brightness reduces the lamp
power consumption and extends the
lamp life.
Lamp control
Remote control
Lamp life control
This projector provides two different remote control codes:
the factory-set initial code (Code 1) and the secondary code
(Code 2). This switching function prevents remote control
interference when operating several projectors or video
equipment at the same time.
When operating the projector in "Code 2", both the projector
and the remote control must be switched to "Code 2".
To change the code for the projector:
Select either "Code 1" or "Code 2" in this Setting Menu.
To change the code for the remote control:
Press and hold both the MENU and IMAGE buttons
together for 5 seconds or more. After changing the code,
make sure the remote control operates properly.
Lamp control
Select the lamp operation when the total lighting time of a
lamp exceeds the recommended total hours of use.
Mode 1 .............. A lamp can be turned on even after
exceeding the recommended total
hours of use.
Mode 2 .............. A lamp can be turned on even after
exceeding the recommended total
hours of use. But the projector turns off
automatically after 3 minutes.
Lamp life control
Note:
When different codes are set on the projector and on the remote control, any operation cannot be made. In
that case, switch the code on the remote control to fit the code on the projector.
• If the batteries are removed from the remote control for a long period of time, the remote control code will be
reset.
Note:
• Lamp mode cannot be changed for a while after turning
on the projector. Lamp needs some time to stabilize
after the power is turned on. Stored lamp mode will be
active after the lamp is stabilized.
• If Mode 2 has been selected and the projection lamp
exceedes the recommended total hours of use, the
replacement icon will be displayed at the time of power-
on. Then the projector will turn off after 3 minutes.
• The Lamp replacement icon will not appear when the
Display function is set to Off (p.46), during
Freeze
(p.25), or No show (p.26).
Lamp replacement icon
Setting
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo plc xu300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo plc xu300 in the language / languages: English as an attachment in your email.

The manual is 18,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo plc xu300

Sanyo plc xu300 User Manual - English - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info