215461
59
Zoom out
Zoom in
Previous page
1/71
Next page
59
Problem: – Solutions
No power – Plug the power cord of the projector into the AC outlet.
– See if the POWER indicator lights red.
Wait until the POWER indicator stops blinking to turn on the projector
again. The projector can be turned on after the POWER indicator
turns red. See page 19.
– Check the WARNING indicator. If the WARNING indicator lights red,
projector cannot be turned on. See page 54.
– Check the projection lamp. See page 57.
– Unlock the Key lock function for the projector. See page 50.
The initial display is not shown. – Make sure "Off" or "Countdown off" are not chosen at display
function.(see page 44)
The initial display is not same – Make sure "User" or "Off" are not chosen at Logo (select)
as the default set. function.(see page 45)
Input signal switches automatically. – Make sure Input search function is adjusted properly. See page 47.
(or does not switch automatically)
When the projector is on and you – That is the Filter warning icon. Refer to page 53.
press the input button, an icon
other than the Lamp mode icon
appears.
An icon other than Input mode or – That is the Lamp replacement icon or the Filter warning icon. See
Lamp mode icon appears. page 52 or 53.
Image is out of focus. – Adjust focus of the projector. See page 23.
– Provide proper distance between the projector and the projection
screen. See page 14.
– Check the projection lens to see if it needs cleaning. See page 56.
– Moving the projector from a cool to warm place may result in
moisture condensation on the projection lens. In such cases, leave
the projector off and wait until condensation evaporates.
Image is Left/Right reversed. – Check the Ceiling/Rear function. See page 47.
Image is Top/Bottom reversed. – Check the Top/Bottom function. See page 47.
Picture is not bright enough. – Check if the 'Contrast" or "Brightness" are adjusted properly.(see
page 33,40)
– Check if "Image mode" is selected properly.(see page 32,39)
– Check the lamp control function.(see page 25)
– Check the LAMP REPLACE indicator. If it lights, the end of lamp life
is approaching. Replace the lamp with a new one promptly.(see page
57)
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
Make sure you have properly connected the projector to peripheral equipment as described on pages 16-18.
Make sure all equipment is connected to AC outlet and the power is turned on.
When the projector does not project an image from the connected computer, restart the computer.
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo plc xu105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo plc xu105 in the language / languages: English as an attachment in your email.

The manual is 9,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info