215608

Sanyo plc xt35l Manual

64
Zoom out
Zoom in
Previous page
1/78
Next page
64
off and wait until condensation evaporates.
– Projecting from the excessive slant angle to the screen may cause
keystone distortion and partial imperfect focus. See page 18.
Picture is not bright enough. – Check if "Contrast" or "Brightness" are adjusted properly See page 42.
– Check if "Image level" is selected properly See page 41.
– Check the LAMP REPLACE indicator. If it lights, the end of lamp life is
approaching. Replace the lamp with a new one promptly. See pages
59-60, 69.
– Check the Lamp control function See page 49.
The color is strange. – Check the Input signal, color system, video system, or computer
system mode.
– Adjust the Image level properly. See page 41.
Image is Left/Right reversed. – Check the Ceiling/Rear function. See page 45.
Image is Top/Bottom reversed. – Check the Ceiling function. See page 45.
The image is distorted or runs off. – Check the "PC Adjustment" menu or "Screen" menu and adjust them.
See page 37-40, 45-47.
The edge of image is distorted. – With maximum lens shift, image distortion may be observed.
No sound – Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. See page 29.
– Press the Mute button. See page 29.
– When the AUDIO OUT is plugged in, the projector's built-in speaker is
not available.
– Is the image projected? You will hear the sound only when the image is
projected.
Auto PC adjustment function – Check the Input signal. Auto PC Adjustment function can not work.
does not work. when 480p, 575p, 720p, 480i, 575i, 1035i, or 1080i is selected.
See page 38.
– The Auto adj. icon turns gray and cannot be operated with the digital
signals. See page 38.
Some displays are not seen – Check the Display function. See page 52.
during the operation.
The setting does not remain after – Make sure you selected "Store" after adjusting settings. Some settings
turning off power. cannot be stored if not registered with "Store."
Power management function does – Power management function cannot work while "Freeze" or "No Show"
not work. function is running.
Image disappears automatically – Check the power mamagement function in the Setting. The power
management is set to “On” at the factory.
Appendix
… 64 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo plc xt35l at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo plc xt35l in the language / languages: English as an attachment in your email.

The manual is 4,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info