215626

Sanyo plc xf70 professional projector Manual

52
Zoom out
Zoom in
Previous page
1/84
Next page
52
Power management
Time left before the lamp is off
Press the SELECT button at Power
management and the dialog box
appears. Use the Point 7 8
buttons to choose one of the three
options.
Press the Point d button to select
the timer, and then use the Point 7
8 buttons to set the timer
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the projector is not used for a certain
period.
If the input signal is interrupted and no button is pressed for
more than 30 seconds, the timer display with “No signal”
appears. It starts the countdown until the lamp is turned off. The
countdown time can be set between 1 and 30 minutes.
Use the Point 7 8 buttons to set the countdown timer.
Select one of the following options:
Ready
. . . . When the lamp has been fully cooled down, the
READY indicator starts blinking. In this condition,
the projection lamp is turned on if the input
signal is reconnected or any button on the side
control or remote control is pressed .
Shutdown
. . When the lamp has been fully cooled down, the
power is turned off.
Off
. . . . . . . Power Management function is off.
Power management
✔Note:
•Factory default is “Ready: 5 min.”
• When the shutter is closed while the Power management function
is working, the Power management function is released.
Setting
RC sensor
Select a location of the infrared remote receiver of the remote
control. See “Remote Control Receivers and Operating Range”
on page 15 for details.
Both ......... Activate both the front and back receiver.
Front ........ Activate only the front receiver.
Back ......... Activate only the back receiver.
Remote control
Remote control
When pressing the SELECT button at
Remote control, the Remote control
code menu appears.
The eight different remote control codes (Code 1–Code 8) are
assigned to the projector; the factory-set, initial code (Code 1)
and the other seven codes (Code 2 to Code 8).
The same code should be set on both the projector and the
remote control. For example, operating the projector in “Code
7”, the remote control code also must be switched to “Code 7”.
To change the code for the projector;
Select a remote control code in this Setting Menu.
To change the code for the remote control;
Check the Reset Switch to "Use position" in the compartment
lid on the back of the remote control.
And then during holding down the MENU button, press the
IMAGE ADJ. button corresponding times to the number of the
remote control code for the projector. (See page 16)
To reset the code for the remote control;
Slide the Reset Switch to "Reset position" in the compartment
lid on back of the remote control.
… 52 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo plc xf70 professional projector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo plc xf70 professional projector in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info