215459
23
Zoom out
Zoom in
Previous page
1/79
Next page
23
Turning On the Projector
Connect the projectors AC power cord into an AC
outlet and turn the MAIN ON/OFF Switch to ON. The
LAMP indicator lights red and the READY indicator
lights green.
Press the ON/STAND-BY button on the side control
or on the remote control. The LAMP indicator
dims red and the cooling fans start to operate. The
preparation display appears on the screen and the
countdown starts.
2
3
1
16
The preparation display will disappear after 20
seconds.
4
After the countdown, the input source that was
selected the last time and the Lamp mode icon (see
page 56) appear on the screen.
If the projector is locked with a PIN code, PIN code
Input Dialog Box will appear. Enter the PIN code as
instructed below.
Selected Input Source and Lamp control
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
What is PIN code?
PIN (Personal Identification Number) code is a security
code that allows the person who knows it to operate the
projector. Setting a PIN code prevents unauthorized use
of the projector.
A PIN code consists of a four-digit number. Refer to the
PIN code lock function in the Setting Menu on page 52-
53 for locking operation of the projector with your PIN
code.
PIN code Input Dialog Box
Enter a PIN code
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector
can no longer be started. Take special care
in setting a new PIN code; write down the
number in a column on page 75 of this
manual and keep it at hand. Should the
PIN code be missing or forgotten, consult
your dealer or service center.
After the OK icon
disappears, you can
operate the projector.
Lamp mode
See page 56 for the Lamp control status
Note:
The Lamp replacement icon and the Filter
warning icon may appear on the screen
depending on the usage state of the projector.
Use the Point ed buttons on the side control or on the
remote control to enter a number. Press the Point 8
button to fix the number and move the red frame pointer
to the next box. The number changes to .” Repeat
this step to complete entering a four-digit number. After
entering the four-digit number, move the pointer to “Set.
Press the SELECT button so that you can start to operate
the projector.
If you fixed an incorrect number, use the Point 7 button
to move the pointer to the number you want to correct,
and then enter the correct number.
If you entered an incorrect PIN code, “PIN code” and the
number (✳✳✳✳) will turn red for a moment. Enter the
correct PIN code all over again.
Note:
When the Logo select function is set to “Off,” the
logo will not be shown on the screen (p.48).
When the “Countdown off” or “Off” is selected
in the Display function, the countdown will not
be shown on the screen (p.47).
During the countdown period, all operations are
invalid.
If the correct PIN code number is not entered
within three minutes after the PIN code dialog
box appeared, the projector will be turned off
automatically.
The “1234” is set as the initial PIN code at the
factory.
Basic Operation
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo plc xf47 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo plc xf47 in the language / languages: English as an attachment in your email.

The manual is 5,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info