489588
18
Zoom out
Zoom in
Previous page
1/80
Next page
18
Basic Operation
Connect the projectors AC power cord into an AC
outlet. The POWER indicator becomes red.
Press the POWER ON/STAND-BY button on the
top control or on the remote control. The POWER
indicator becomes green and the cooling fans start
to operate. The preparation display appears on the
screen and the count down starts.
2
3
1
4
After the countdown, the input source that was
selected the last time and the Lamp mode status icon
(see page 51) appears on the screen.
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
Turning On the Projector
To Enter a PIN code
Select a number by pressing the Point ▲▼ buttons,
and then press the Point button to fix the number
and move the pointer. The number changes to "". If
you fixed an incorrect number, move the pointer to the
number you want to correct by pressing the Point
button, and then select the correct number by pressing
the Point ▲▼ buttons.
Repeat this step to complete entering a four-digit
number.
"1234" is set as the initial PIN code at the factory.
After entering the four-digit number, move the pointer
to "Set" by pressing the Point button. Press the
SELECT button so that you can start to operate the
projector.
If you entered an incorrect PIN code, "PIN code" and
the number () turns red. Enter the correct PIN
code all over again.
What is PIN code?
PIN (Personal Identification Number) code that allows
the person who knows it to operate the projector.
Setting a PIN code prevents unauthorized use of the
projector.
A PIN code consists of a four-digit number. Refer to the
PIN code lock function in the Setting on pages 53 and
54 for locking operation of the projector with your PIN
code.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no longer
be started. Set a new PIN code with special care,
write it down in column on page 79 of this manual, and
keep it on hand. Should the PIN code be missing or
forgotten, consult your dealer or service center.
16
The preparation display disappears after 30
seconds.
(See page 51 for Lamp mode.)
Note:
The Filter warning and Lamp replacement icons
may appear on the screen depending on the
usage state of the projector.
Selected Input Source and Lamp Mode
Lamp mode
After th e OK ic o n
disappears, you can
operate the projector.
PIN Code Input Dialog Box
If the projector is locked with a PIN code, PIN code
Input Dialog Box appears. Enter the PIN code as
instructed below.
Notes:
When the Input Search function is set
On1 or On2, the input signal will be
searched automatically (p.46)
When the Logo select function is off,
the logo is not shown on the screen.
(p.48)
When the "Countdown off" or "Off" is
selected in the Display function, the
countdown is not shown on the screen.
(p.47)
During the countdown period, all
operations are invalid.
If the PIN code number is not input for
three minutes after the PIN code dialog
box appeared, the projector is turned off
automatically.
Basic Operation
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PLC-XC50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PLC-XC50 in the language / languages: English as an attachment in your email.

The manual is 5,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PLC-XC50

Sanyo PLC-XC50 User Manual - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info