598874
57
Zoom out
Zoom in
Previous page
1/98
Next page
Setting
Picture in Picture
Picture in Picture
Show the selected mode (Off/User 1-5) and its status
(Stored /Free/ Adj.). User 1 and User 2 have stored
default values. See page 29 for details.
User setting
P in P:
Provide the images of Main picture and Sub
picture at the ratio of Screen aspect in the Screen
Menu.
P by P:
Provide the images of Main picture and Sub
picture at the ratio of 4:3.
P in P/P by P
Selected
Mode
Status (Stored /
Free/ Adj.) of the
selected mode.
Main picture / Sub picture
Input
……
Select an input from Input 1-3.
Source
Select an input source. The display varies
depending on the selected input.
Size
………
Select the display size. Main picture can be
changed between 10 and 100%, and Sub
picture can be changed between 10 to 50% in
increments of 10%. When P by P is selected in
Mode, the projection size is fixed to 50%.
Position
Press the SELECT button at Position and the
display position setting screen appears.
Use the Point
▲▼◄►
buttons to adjust the display
position of active frame indicated in white. The frame will
disappear after 10 seconds or when the SELECT button is
pressed.
Position Menu
Active frame
(White)
Center line
display
Selecting the Main picture or Sub picture
During Picture in Picture mode, and being undisplayed On
Screen Menu, press the SELECT button to select Main or
Sub picture. (A red frame will be displayed on the selected
picture.)
Switching Input and Source
When selecting Main picture or Sub picture, input and
source can be set by pressing the INPUT button on the
side control or INPUT 1/2/3 button on the remote control.
Operation on the On Screen Menu is not necessary.
Note:
•ThePictureinPicturefunctionis
notavailabledependingonthe
inputsignalsandtheselectedinput
terminals.RefertoList of Picture in
Picturefordetails.(p.95)
•Whentheinputsignal(s)is/are
incompatible,Xmarkwillbedisplayed
for10secondsontheMain/Sub
picture.
This function is used to project two images simultaneously
by placing a separate small sub screen within or next to the
main screen.
Use the Point
▲▼
buttons to select Picture in Picture and
then press the SELECT button to display a dialog box. You
can also display the dialog box by pressing and holding the
PIP button on the remote control for more than 3 seconds.
( In P in P, the larger picture is main picture, and the smaller
one is sub picture; in P by P, the left picture is main picture,
and the right one is sub picture.)
Note:
•WhenPIP isselected,screenisnot
available.
57
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PLC HP7000L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PLC HP7000L in the language / languages: English as an attachment in your email.

The manual is 19,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info