Manual Sanyo PLC HP7000L (page 23 of 98) (English)

598874

Zoom out

Zoom in

1/98

The preparation display will disappear

after 30 seconds.

After the countdown, the input source that was

selected the last time and the Lamp control status icon

(see page 61) appear on the screen.

Selected Input Source and Lamp control

Complete peripheral connections (with a computer,

VCR, etc.) before turning on the projector.

Note:

 •TheLampreplacementiconandthe

FilterreplacementortheFiltercartridge

replacementiconmayappearonthe

screendependingontheusagestateof

theprojector.

 •Whenthefiltercartridgereplacement

iconkeepsappearingonthescreen

atturningontheprojectorforsome

timeandnoactionistakentoreplace

thefiltercartridge,theprojectorwillbe

automaticallyshutdownin3minutes

afterturningontoprotecttheprojector.

(pp.71-73,87)

 •WhenthePictureinPicturefunctionis

settoUser 1-5,User1-5,Inputsource,

Lampcontrolstatus,Lampreplacement

iconandFilterwarningiconwillappear

onthescreenfor10seconds.

Basic Operation

(See page 61 for Lamp control status.)

Lamp control status

If the projector is locked with a PIN code, PIN code

input dialog box will appear.

Note:

 •WhentheLogoselectfunctionissettoOff,thelogowill

notbeshownonthescreen(p.54).

 •WhenCountdown off orOffisselectedintheDisplay

function,thecountdownwillnotbeshownonthescreen

(p.54).

 •WhentheInputbuttonfunctionissettoMode 3,the

inputsignalwillbesearchedautomatically(p.53).

 •IfyoupresstheON/STAND-BYbuttonontheside

controlortheremotecontrolduringthecountdown

period,youcanskipthecountdownandgotothenormal

operations.Inthiscase,however,thebrightnessofthe

imageneedssometimetostabilizeafterturningonthe

projector.Thedisplaymayflickerafterturningonthe

lampforthecharacteristicsofthelamp.Thisisnormal

operationandnotamalfunction.

After the OK icon disappears, you can

operate the projector.

PIN Code Input Dialog Box

Note:

 •IfthePINcodenumberisnotentered

withinthreeminutesafterthePINcode

dialogboxappears,theprojectorwillbe

turnedoffautomatically.

 •The"1234"issetastheinitialPINcode

atthefactory.

Enter a PIN code

Use the Point

▲▼

buttons on the side control or Number

buttons on the remote control to enter a number.

When using side control

Use the Point

▲▼

buttons on the side control to select a

number. Press the Point

►

button to fix the number and

move the red frame pointer to the next box. The number

changes to . Repeat this step to complete entering a

four-digit number. After entering the four-digit number,

move the pointer to “Set”. Press the SELECT button so

that you can start to operate the projector.

When using remote control

Press the Number buttons on the remote control to enter

a number (p.14). When you complete entering a four-digit

number, the pointer moves to “Set”. Press the SELECT

button so that you can start to operate the projector.

If you fix an incorrect number, use the Point

◄

button to

move the pointer to the number you want to correct, and

then enter the correct number.

If you entered an incorrect PIN code, “PIN code” and the

number () will turn red for a moment. Enter the

correct PIN code all over again.

Turning On the Projector

Input 1

RGB(PC analog)

Connect the projector’s AC power cord into an AC

outlet. The LAMP/SHUTTER indicator lights red and

the POWER indicator lights green.

Press the ON/STAND-BY button on the side control

or the ON button on the remote control. The LAMP/

SHUTTER indicator dims and the cooling fans start

to operate. The preparation display appears on the

screen and the countdown starts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PLC HP7000L in the language / languages: English as an attachment in your email.

The manual is 19,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sanyo PLC HP7000L Manual

Product: