569872
63
Zoom out
Zoom in
Previous page
1/78
Next page
63
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
Make sure you have properly connected the projector to peripheral equipment as described on pages 20–22.
Make sure all equipment is connected to AC outlet and the power is turned on.
When the projector does not project an image from the connected computer, restart the computer.
Problem: Solutions
No power Plug the power cord of the projector into the AC outlet.
See if the POWER indicator is lit.
Wait 90 seconds after the projector is turned off when turning the
projector back on. The projector can be turned on after the POWER
indicator stops blinking. See on page 25.
Check the WARNING TEMP. indicator. If the WARNING TEMP.
indicator is blinking, the projector cannot be turned on. See page 61.
Check the projection lamp. See page 59.
Unlock the Key lock function for the projector. See page 54.
PIN code dialog box appears PIN code lock is being set. Enter a PIN code; the "1234" or numbers
at start-up. you have set. See pages 24, 55–56.
The initial display is not shown. Make sure "Off" or "Countdown Off" are not chosen at Display function.
See page 52.
The initial display is not same with Make sure "User" or "Off" are not chosen at Logo function. See page 50.
the default one.
An icon other than Input mode or That is the Lamp replacement icon or the Filter warning icon.
Lamp mode icon appears. See pages 57, 59.
No image Check the connection between your computer or video equipment and
the projector. See pages 20–22.
See if the input signal is correctly output from your computer. Some
laptop computers may need to change the setting for monitor output
when connecting to the projector See your computer’s instruction
manual for the setting.
It takes about 30 seconds to display an image after turning on the
projector.
See if the selected system is corresponding with your computer or
video equipment. See pages 36, 37.
Select correct input source once again through menu operation. See
page 35.
Make sure the temperature is not out of the specified Operating
Temperature (
41 ˚F–95 ˚F [5 ˚C–35 ˚C]).
When "No Show" is operating, the image can not be displayed. Press
the NO SHOW button or any other button on the remote control.
Image is out of focus. Adjust focus of the projector. See pages 28, 30.
Provide proper distance between the projector and projection screen
See page 18.
Check the projection lens to see if it needs cleaning. See page 62.
Moving the projector from a cool to warm place may result in moisture
condensation on the projection lens. In such cases, leave the projector
off and wait until condensation evaporates.
Appendix
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PLC-ET30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PLC-ET30 in the language / languages: English as an attachment in your email.

The manual is 4,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PLC-ET30

Sanyo PLC-ET30 User Manual - Dutch - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info