569893
49
Zoom out
Zoom in
Previous page
1/52
Next page
iii
CLEANING THE LENS
Follow these steps to clean the projection lens:
1.
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.
Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
2. Lightly wipe the cleaning cloth over the lens.
3. If you don’t intend to use the projector immediately, replace the lens cover.
TROUBLESHOOTING
Before calling your dealer or service station for assistance, follow these steps, in this order, to make sure everything is
properly connected.
1. Make sure you have connected the projector to your equipment as described in section
CONNECTING THE
PROJECTOR” on pages 10
_
17.
2. Check cable connections. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If the projector still does not display an image, restart the computer.
5. If the image still does not display, unplug the projector from the computer and check the computer monitor’s display.
The problem may be with your graphics controller rather than with the projector.
(When you reconnect the projector,
remember to turn the computer and monitor off before you power up the projector. Power the equipment back
up in
this order: Projector, monitor, computer)
6. If the problem still exists, check the following chart.
Problem:
No
power
Image is out of focus
Try these Solutions:
l
Plug the projector into an AC outlet.
l
Turn the MAINS ON/OFF button to ON.
l
Press the LAMP POWER ON/OFF switch to ON.
l
Be sure the READY INDICATOR light is ON.
l
Wait
one minute after the projector is turned OFF before
turning the projector back on.
NOTE: After pressing the LAMP POWER ON/OFF button to
OFF
.
The projector functions as follows.
1. The LAMP POWER indicator will light and the READY
indicator will turn off.
2. After one minute, the READY indicator will light green again
and the projector may be turned on by pressing the LAMP
POWER ON/OFF button.
l
Check temperature warning indicator. If the indicator flashes
red, the projector cannot be turned on.
(See “USING THE PROJECTOR” section on page 27).
l Check the projection lamp.
l
Adjust the focus.
l Make sure the projection screen is at least 1 .I m from the
projector.
l
Check the projection lens to see if it needs cleaning.
NOTE: Moving the projector from a cool temperature location
to a warm temperature location may result in moisture
condensation on the lens. In such an event, leave the
projector OFF and wait until condensation disappears.
-
49
-
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PLC-8810E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PLC-8810E in the language / languages: English as an attachment in your email.

The manual is 3,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PLC-8810E

Sanyo PLC-8810E User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info