19042

Sanyo DWM4500 Manual

40
Zoom out
Zoom in
Previous page
1/44
Next page
-E39-
To turn the unit on and listen to the last received station, press
[TUNER] on the remote control.
Preparation
Press [FUNCTION] to select “FM TUNER”.
Note: This unit doesn't have “AM TUNER”.
Automatic/Manual Tuning
Automatic tuning
Press [TUNE] + or - for at least 1 second to tune in a station. The
unit will scan up or down the band and receive the next receivable
station. Press the button again to continue.
Manual tuning
Press [TUNE] + or - briefly until the desired frequency is displayed.
The frequency changes in 200 kHz steps for FM.
Example:
To Preset Stations
Up to 24 FM stations can be preset.
Automatic presetting (APT)
Press [PROGRAM/RANDOM] for at least 3 seconds.
“PROG.” blinks.
The automatic tuning mode is set and automatic presetting
begins from the low end of the band.
When 24 FM stations have been preset or the high end of the
band is reached, automatic presetting stops. “PROG.” disappears
and the station memorized on the preset number 1 will be heard.
Note:
If APT is activated, all previously programmed stations of the
band will be cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in “Automatic/
Manual Tuning”.
2. Press [PROGRAM/RANDOM]. “PROG.” blinks.
LISTENING TO THE RADIO (FM ONLY)
Listening to Preset Stations
Preset tuning
Press [PRESET] + or - briefly to select the desired channel.
• If using the number buttons, press the number button(s), then
press [ENTER].
Preset scan tuning
1. Press [PRESET] + or - for at least 1 second.
• The preset number appears.
• The preset stations are selected in sequence for
approximately five seconds each.
2. Press [n] when the desired station has been selected. Preset
scanning will stop.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during
reception of radio broadcasts.
If this occurs, while holding [ON SCREEN] down on the remote
control, press [e] on the main unit to select “bc-A” or “bc-B”.
Select the setting that gives the best results.
To receive FM stereo broadcasts
Make sure that “MONO” is not displayed. If “MONO” appears,
press [FM MODE] to turn the “MONO” indication off.
You can enjoy FM stereo sound when an FM stereo broadcast
is received.
• If the signal from an FM stereo station is weak and reception
is poor, press [FM MODE] to change to monaural (MONO)
reception. The reception may be improved, but the sound
will be monaural.
Changing the reception frequencies
If necessary, use the following procedure to change the
reception frequencies.
While holding [ON SCREEN] down on the remote control,
press [f] on the main unit.
To return the original setting, repeat steps above.
87.9 ~ 107.9 MHz 87.5 ~ 108.0 MHz
(200 kHz steps) (50 kHz steps)
3. While “PROG.” is blinking, press [PRESET] + or - to select
the number to be preset.
• The number buttons on the remote control can also be
used.
• In this example, the preset number is “9”.
4. While it is blinking, press [PROGRAM/RANDOM].
• In this example, “103.1 MHz” FM station is preset on the
preset number 9.
5. Repeat steps above to add more preset stations.
• When presetting a new station, the previous preset station is
cleared.
n
(Stop)
FUNCTION
– PRESET +
f, e
ON SCREEN
– TUNE +
ENTER
PROGRAM
/RANDOM
Number
buttons
FM MODE
TUNER
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo DWM4500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo DWM4500 in the language / languages: English as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info