19032
12
Zoom out
Zoom in
Previous page
1/42
Next page
-E11-
1
2
1
2
3
PHONES
AUDIO
OUTPUT
L
R
Antenna Connections
FM antenna
The FM indoor antenna lead wire is sufficient to receive most
local FM broadcasts and should be connected to the rear FM
75 terminal. Extend the antenna lead wire as straight as possible
and, while listening to the sound from the system, secure it in a
position where the best FM reception is found.
In fringe areas, or where reception is distorted or noisy, an FM
outdoor antenna (not supplied) should be connected instead of
the FM indoor antenna lead wire. The terminals will accept 75-
ohm coaxial cable.
AM antenna
The AM loop antenna is sufficient to
receive most local AM broadcasts.
Assemble the loop antenna.
Unwind the antenna wires, then
connect the plug to the AM LOOP
terminal. If you have difficulty inserting
the plug, turn it over and reinsert it.
Place the loop antenna in a position
which yields the best AM reception, or
attach it to a wall or other surface as
shown.
NOTE:
To minimize noise...
Keep the speaker wires, power cord and all other system
connection cables away from the loop antenna.
Do not place the antenna close to a TV or speaker.
Note to CATV system installer:
This reminder is provided to call the CATV system installers
attention to Section 820-40 of the NEC which provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Screws (not supplied)
FM outdoor antenna
(not supplied)
AM loop antenna
Antenna discharge unit (not supplied)
FM indoor antenna
lead wire
75-ohm coaxial cable
(not supplied)
CAUTION:
When installing an outdoor antenna, follow the installation
instructions in the attached IMPORTANT SAFETY
INSTRUCTIONS.
Additional Connection Examples
2
nd
video equipment input jack (VIDEO (AUDIO) IN 2)
Connect an audio cable (not supplied) from the audio output
jacks of the video equipment to the VIDEO (AUDIO) IN 2 jacks.
Audio cable
(not supplied)
Headphones jack (PHONES)
Connect a pair of stereo headphones with miniplug (8 ohms - 32
ohms, not available from SANYO) to the PHONES jack for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.
Power Supply
Connect the power cord to a 120VAC 60Hz outlet. This unit is
equipped with a polarized plug. If you have difficulty inserting the
plug, turn it over and reinsert it. If the unit will not be used for a
long time, disconnect the AC plug from the AC outlet.
Notes:
Before plugging the power cord into an AC outlet, make sure
that all the connections have been made.
The unit is not disconnected from the AC power unless the
power cord is unplugged from the AC outlet.
TV
Ground
1
st
video equipment input jack
(VIDEO (AUDIO) IN 1)
Connect an audio cable (not supplied) from
the audio output jacks of the TV to the VIDEO
(AUDIO) IN 1 jacks.
Plug
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo DWM2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo DWM2500 in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info