30748
6
Zoom out
Zoom in
Previous page
1/44
Next page
6
EN
Setup
Select this connection when you want to view or record a scram-
bled channel. With this connection, channels cannot be changed
on the unit. You can view or record ONLY the channels you have
selected on the cable box or the satellite box.
While you are recording, only the recorded channel can be
viewed.
To select channels of the cable box or satellite box
1) Turn on the unit by pressing [POWER], then press [VCR/TV].
The POWER light on the front panel will appear, then press
[SKIP/CH.
ii
/
KK jj
/
LL
] to select channel 3 or 4 (the same
channel as the output channel of the cable box or satellite
box).
If you use the channel 4, you need to change the units RF
output to channel 4. Refer to RF Output Channel.
2) On the TV, select channel 3 or 4 (the same channel as you
have selected at step 1).
3) On the cable box or satellite box, select the channel you want
to view or record.
Select this connection when you want to change channels on the unit. With
this connection, you may watch one channel while recording another.
You may not view or record a scrambled channel.
To select channels of the cable box
1) On the cable box, select channel 3 or 4 (the same channel as
the units RF output channel).
Refer to RF Output Channel.
2) On the TV, select the same channel as the output channel (3
or 4) of the cable box.
3) Turn on the unit by pressing [POWER], then press [VCR/TV].
The POWER light on the front panel will appear, then select
the channel you want to view or record.
To pla
y back a tape
Follow the steps 1) to 2) above, then play back a tape.
Refer to Playbackon page 11.
To vie
w one channel while recording another
1)
While you are recording on the unit, press [VCR/TV
]
.
2) On the cable box, select the channel you want to view.
ANT-OUT
ANT-IN
RF cable
(supplied)
(Back of DVD+VCR)
IN
OUT
E
(Back of TV)
Antenna or
cable TV
signal
Connection A
(Cable box or
Satellite box)
ANT-OUT
ANT-IN
RF cable (supplied) RF cable
(Back of TV)
IN
OUT
(Cable box)
E
Antenna or
cable TV
signal
Connection B
(Back of DVD+VCR)
Hints for Cable Box or Satellite Box
LR
VCRDVD/VCR
AUDIO OUT
L
R
DIGITAL
AUDIO OUT
or
AUDIO
OUT
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
L
R
Stereo system
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
COAXIAL
AUDIO
DVD+VCR
Method 1
Analog audio
input jacks
Digital audio
input jack
(Analog)
AUDIO OUT
DIGITAL
AUDIO OUT
Method 2
Connection to an Audio System
Audio cable
(supplied)
Audio Coaxial
Digital cable
(commercially
available)
Dolby Digital decoder,
MD deck or DAT deck
BITSTREAM
PCM
SETUP > AUDIO menu >
DOLBY DIGITAL
PCM
SETUP > AUDIO menu >
DOLBY DIGITAL
Connecting to a Dolby Digital decoder
for Dolby Digital audio output.
Connecting to the other equipment (an MD deck
or DAT deck etc.) without Dolby Digital decoder.
* To complete these settings, refer to pages 20-21.
Hint
Hint
The audio source on a disc in a Dolby Digital 5.1 channel surround
format cannot be recorded as digital sound by an MD or DAT deck.
By hooking this unit up to a Multi-channel Dolby Digital
decoder, you can enjoy high-quality Dolby Digital 5.1
channel surround sound as heard in the movie theaters.
Playing a DVD using incorrect settings may generate
noise distortion and may also damage the speakers.
Connecting to Stereo System.
Setting
Connection
* To complete these settings, refer to pages 20-21.
Hint
Hint
Playing a DVD using incorrect settings may generate
noise distortion and may also damage the speakers.
Connection
Setting
(DVD mode only)
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press
[OUTPUT] on the unit so that the VCR
OUTPUT light is lit.
If noise appears on the TV screen, press
[VCR/TV] on the remote control.
4) Press [PLAY B] once.
5) After a few seconds, press [PLAY
BB
] on
the unit for 3 seconds.
The RF output channel will change to
channel 4 from channel 3 and you will
see a playback picture.
When a picture does not appear on the
TV screen, repeat step 4).
6) Press [STOP C] to stop playback.
RF Output Channel
Connections
Please refer to Basic TV Connectionon the front page before you use this unit.
Hint
Hint
The RF output channel may
not change when you adjust
tracking during playback. In this
case, stop the playback, and
start the playback again. After
that, press [PLAY
BB
] on the
unit for 3 seconds again.
Setup
Need help? Call
1-800-813-3435
H9880UD(EN).qx3 05.1.17 17:30 Page 6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo DVW7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo DVW7200 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info