48899

Sanus Systems SD103 Manual

18
Zoom out
Zoom in
Previous page
1/24
Next page
18
EN
Step 7: Adjust Pillar Height (Optional)
CAUTION: Do not adjust the Pillar height if a monitor is attached. Sanus Systems is not
responsible for property damage and/or personal injury.
Remove the Cable Cover [C] from the Pillar [A], and lift the monitor cables out of the channel
on the Pillar. See Step 6 for additional information. Remove the Monitor Mount [B] and the
attached monitor from the Pillar. See Step 5 for additional details about how the Monitor
Mount and Pillar fit together.
Loosen the two screws at the top of the Pillar with a Phillips screwdriver. See Figure 7. Slide the
bushing on the Pillar to the desired height, and tighten the screws with the screwdriver. Replace
the Monitor Mount with attached monitor as described in Step 5. Replace the monitor cables and
Cable Cover as described in Step 6.
ES
Paso 7: Ajuste la altura del poste (optativo)
ADVERTENCIA: No ajuste la altura del poste cuando el monitor se encuentre sujeto a él.
Sanus Systems no es responsable por daños materiales y/o lesiones personales.
Retire la cubierta de cables [C] del poste [A] y saque los cables del monitor del túnel del poste.
Para más información, consulte el paso 6. Retire del poste el soporte del monitor [B] y el
monitor acoplado. Para más detalles sobre como se acoplan el soporte del monitor y el poste,
consulte el paso 5.
Afloje los dos tornillos de la parte superior del poste con ayuda de un destornillador tipo Phillips.
Vea la figura 7. Deslice el manguito sobre el poste hasta la altura deseada y vuelva a apretar los
tornillos con el destornillador. Vuelva a colocar el soporte del monitor con el monitor acoplado,
tal como se describe en el paso 5. Vuelva a poner en su sitio los cables del monitor y la cubierta
de cables, como se describe en el paso 6.
DE
Schritt 7: Säulenhöhe verstellen (optional)
VORSICHT: Säulenhöhe nicht bei angebrachtem Monitor verstellen. Sanus Systems haftet
nicht für Sachschäden und/oder Körperverletzungen.
Kabelabdeckung [C] von der Säule [A] entfernen und Monitorkabel aus dem Kanal an der Säule
herausheben. Bezüglich weiterer Informationen siehe Schritt 6. Monitorhalterung [B] und
den angebrachten Monitor von der Säule entfernen. Bezüglich weiterer Details darüber, wie
Monitorhalterung und Säule zusammenpassen, siehe Schritt 5.
Die beiden Schrauben an der Oberseite der Säule mit einem Kreuzschlitzschraubenzieher lösen.
Siehe Abbildung 7. Buchse an der Säule in die gewünschte Höhe schieben und die Schrauben
mit dem Schraubenzieher anziehen. Monitorhalterung mit angebrachtem Monitor gemäß der
Beschreibung in Schritt 5 wieder einbauen. Monitorkabel und Kabelabdeckung gemäß der
Beschreibung in Schritt 6 wieder anbringen.
FR
Étape 7 : réglage de la hauteur sur la colonne (en option)
ATTENTION : Ne pas ajuster la hauteur sur la colonne lorsqu’un moniteur y est suspendu.
Sanus Systems n’est pas responsable des préjudices corporels et des dommages matériels.
Ôtez le couvercle de la goulotte [C] sur la colonne [A] et retirez les câbles hors de la goulotte.
Voir l’étape 6 pour toute information complémentaire. Ôtez de la colonne l’ensemble formé par
l’applique [B] et le moniteur. Voir l’étape 5 pour plus de détails concernant la mise en place de
l’applique sur la colonne.
Desserrez les deux vis au bas de la colonne à l’aide du tournevis cruciforme. Voir la figure 7. Glissez
le tenon jusqu’à la hauteur désirée et serrez les vis avec le tournevis. Replacez l’ensemble formé
par l’applique et le moniteur comme décrit à l’étape 5. Replacez les câbles et le couvercle comme
décrit à l’étape 6.
IT
Fase 7: regolazione dell’altezza della colonna (opzionale)
PRECAUZIONE: Non effettuare la regolazione dell’altezza della Colonna con il monitor
montato. Sanus Systems declina ogni responsabilità per danno a cose e/o lesioni personali.
Rimuovere il Copricavo [C] dalla Colonna [A] e sollevare i cavi del monitor facendoli uscire
dalla canalina della colonna. Per ulteriori informazioni fare riferimento alla Fase 6. Rimuovere
il Supporto Monitor [B] e il monitor dalla colonna. Per ulteriori dettagli su come assemblare
supporto monitor e colonna fare riferimento alla Fase 5.
Allentare le due viti alla sommità della colonna usando un cacciavite a croce. Fare riferimento alla
Figura 7. Far scivolare la boccola presente sulla colonna all’altezza desiderata, quindi serrare le
viti usando il cacciavite. Ricollocare il supporto monitor e il monitor come descritto nella Fase 5.
Riposizionare i cavi del monitor e il copricavo come descritto nella Fase 6.
PT
Passo 7: Ajuste a Altura da Coluna (opcional)
ATENÇÃO: Não ajuste a altura da coluna com o monitor já instalado. A Sanus Systems não se
responsabiliza por danos da propriedade e/ou ferimentos pessoais.
Retire a Cobertura dos Cabos [C] da Coluna [A] e retire os cabos do monitor da conduta da Coluna.
Veja o Passo 6 para informação adicional. Retire o Suporte de Monitor [B] e o monitor da Coluna.
Veja o Passo 5 para informação detalhada sobre o encaixe do Suporte de Monitor e da Coluna.
Desaperte os dois parafusos no cimo da Coluna com uma chave Phillips. Veja Figura 7. Deslize o
casquilho da Coluna até à altura desejada e aperte os parafusos com a chave. Volte a colocar o
Suporte de Monitor com o monitor da forma descrita no Passo 5. Coloque os cabos novamente
na conduta e encaixe a cobertura conforme indicado no Passo 6.
NL
Stap 7: Instellen zuilhoogte (optioneel)
PAS OP: Om persoonlijk letsel of schade aan eigendommen te voorkomen, raden wij u aan
de hoogte van de zuil niet aan te passen als er reeds een monitor bevestigd is. Sanus Systems is
niet verantwoordelijk voor beschadiging van eigendommen en/of persoonlijk letsel.
Verwijder de kabelafdekking [C] van de zuil [A] en trek de monitorkabels voorzichtig uit de goot
op de zuil. Zie Stap 6 voor meer informatie. Neem de monitorsteun [B] en de daaraan bevestigde
monitor van de zuil. Zie Stap 5 voor meer informatie over hoe de monitorsteun en de zuil aan
elkaar bevestigd zijn.
Draai de twee schroeven bovenaan de zuil los met een kruiskopschroevendraaier. Zie Afbeelding
7. Schuif de draagbus naar de gewenste hoogte en draai de schroeven weer vast met de
kruiskopschroevendraaier. Vervang de monitorsteun en de daaraan bevestigde monitor zoals
beschreven in Stap 5. Vervang de monitorkabels en kabelafdekking zoals beschreven in Stap 6.
TR
Adım 7: Sütun Yüksekliğini Ayarlayın (İsteğe Bağlı)
DİKKAT: Monitör takılıyken Sütun yüksekliğini ayarlamayın. Kişisel yaralanma ve/veya hasarlı
ürünlerden Sanus Sistemleri sorumlu değildir.
Kablo Kılıfını [C] Sütundan [A] çıkarıp Sütun kanalındaki monitör kablolarını kaldırın. Ayrıntılı bilgi
için bkz. Adım 6. Monitör Montaj Askısı [B] ve askıya takılı monitörü Sütundan çıkarın. Monitör
Montaj Askısı ve Sütunun birlikte nasıl takıldığı hakkında ayrıntılı bilgi almak için bkz. Adım 5.
Sütun üstündeki iki vidayı Phillips tornavida kullanarak gevşetin. Bkz. Şekil 7. Sütun kılavuzunu
istediğiniz yüksekliğe ayarlayıp vidaları tornavida ile sıkın. Monitör Takılı Montaj Askısını Adım 5’te
belirtildiği şekilde değiştirin. Monitör kabloları ve Kablo Kılıfını Adım 6’da belirtildiği gibi değiştirin.
7
6901-210121
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanus Systems SD103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanus Systems SD103 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info