48899

Sanus Systems SD103 Manual

14
Zoom out
Zoom in
Previous page
1/24
Next page
14
[B]
[A]
[K]
[J]
[H]
[I]
[B]
[A]
5b
5a
EN
Step 5: Attach the Monitor Mount and Monitor to the Pillar
NOTE: So that all the parts can be seen clearly, the monitor is not shown in Figure 5b.
Set the tapered hole in the Monitor Mount [B] down over the cone-shaped bushing on the Pillar
[A]. Make certain the Monitor Mount is completely seated onto the Pillar. Add the Large Washer
[H] and the Small Cap [I], turning the Small Cap until its square cut fits over the square top of the
bushing. Finally, place the Round Knob [K] through the Small Washer [J] and into the Small Cap.
See Figures 5a and 5b for reference. You can now set the desired level of tension for the knob.
ES
Paso 5: Sujete el soporte del monitor y el monitor al poste
NOTA: En la figura 5b se muestra este paso sin el monitor, para que puedan verse todas las
piezas claramente.
Coloque el orificio cónico del soporte del monitor [B] sobre el manguito cónico del poste [A].
Cerciórese de que el soporte del monitor se encuentre completamente asentado en el poste.
Añada la arandela grande [H] y el casquillo pequeño [I], girándolo hasta que el corte cuadrado
encaje en el extremo cuadrado del manguito. Por último, inserte el botón redondo [K], a través
de la arandela pequeña [J], en el casquillo pequeño. Para referencia, vea las figuras 5a y 5b. Ahora
podrá ajustar el nivel deseado de tensión para el botón.
DE
Schritt 5: Monitorhalterung und Monitor an der Säule anbringen
HINWEIS: Damit alle Teile gut zu sehen sind, zeigt Abbildung 5b den Monitor nicht.
Das konische Loch in der Monitorhalterung [B] nach unten über die konische Buchse an der Säule
[A] schieben. Sicherstellen, dass die Monitorhalterung vollständig auf der Säule aufliegt. Große
Unterlegscheibe [H] und kleine Kappe [I] hinzufügen, wobei die kleine Kappe zu drehen ist, bis
ihr quadratischer Ausschnitt auf die quadratische Oberseite der Buchse passt. Schließlich wird
der runde Knopf [K] durch die kleine Unterlegscheibe [J] und in die kleine Kappe eingesetzt.
Bezüglich Einzelheiten siehe die Abbildungen 5a und 5b. Nun können Sie die gewünschte
Zugbeanspruchung für den Knopf einstellen.
FR
Étape 5 : Fixation de l’ensemble formé par l’applique et le moniteur sur la colonne
NOTE : Afin de présenter clairement toutes les pièces, le moniteur n’est pas représenté sur la figure 5b.
Placez le trou conique de l’applique [B] sur le tenon conique sur la colonne [A]. Assurez-vous que
l’applique est bien entièrement emboîtée sur le tenon de la colonne. Ajoutez la grande rondelle
[H] et le petit capuchon [I], en tournant le petit capuchon jusqu’à ce que la section carrée s’adapte
sur le sommet carré du tenon. Enfin, faites passer le bouton rond [K] à travers la petite rondelle [J]
et dans le petit capuchon. Utilisez les figures 5a et 5b pour références. Vous pouvez maintenant
régler le niveau souhaité de tension pour le bouton.
IT
Fase 5: Montaggio del supporto monitor e del monitor alla colonna
NOTA: Al fine di visualizzare tutte le parti chiaramente il monitor non è mostrato nella Figura 5b.
Posizionare il foro conico nel Supporto Monitor [B] verso il basso, rivolto sulla boccola conica
della Colonna [A]. Assicurarsi che il supporto monitor sia ben allocato sulla colonna. Collocare
la Rondella Grande [H] e il Cappuccio Piccolo [I], fare girare il cappuccio piccolo finché il taglio
quadro s’incastra sulla sommità quadra della boccola. Collocare infine il Pomello Tondo [K]
facendolo passare attraverso la Rondella Piccola [J] e il cappuccio piccolo. Fare riferimento alle
Figure 5a e 5b. A questo punto è possibile impostare la tensione desiderata del pomello.
PT
Passo 5: Una o Suporte de Monitor e o Monitor à Coluna
NOTA: Para que todas as partes possam ser ilustradas de forma bem clara, neste passo na Figura 5b não
é ilustrado o monitor.
Coloque a abertura cónica do suporte de monitor [B] no casquilho cónico na Coluna [A].
Assegure-se que o suporte de monitor está completamente apoiado na coluna. Depois coloque
a Anilha Grande [H] e a tampa de remate pequena, virando-a até que o corte quadrado encaixe
na extremidade quadrada do casquilho cónico. Finalmente coloque o Botão Redondo [K] pela
Anilha Pequena [J] e a Tampa de Remate Pequena. Veja as Figuras 5a e 5b para referência. Agora
pode ajustar a tensão desejada do botão.
5
6901-210121
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanus Systems SD103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanus Systems SD103 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info