626686

Sanitas SBG 43 Manual

20
Zoom out
Zoom in
Previous page
1/64
Next page
20
Only weight measurement
Press the „[SET/ON]“ button on the display module. The entire display appears as a
self-test until “- - - -“ is displayed (Fig. 1).
Audibly, briefly and firmly tap the scale with your foot to activate the vibration
sensor. The LED first shows red and then switches to green after about 5 se-
conds.
If the control panel is receiving the signal from the scale it shows „0.0“ (Fig. 2).
Now the scale is ready to measure your weight. Now step onto the scale. Stand still
on the scale with your weight distributed evenly between both legs. The scale imme-
diately begins to measure your weight.
Weighing, carrying out diagnostics
• Press the „[SET/ON]“ button on the control panel. The complete LCD display ap-
pears, then “- - - -“ is displayed.
• Now press the button
.
• Select the memory space where your personal data are stored by repeatedly pres-
sing the
or keys and confirm with „[SET/ON]“. These data are then displayed
consecutively until “- - - -” appears (Fig. 1).
• Audibly, briefly and firmly tap the scale with your foot to activate the vibration sen-
sor. The LED first shows red and then switches to green after about 5 seconds.
If the control panel is receiving the signal from the scale it shows „0.0“ (Fig. 2).
• Step onto the scale barefoot and make sure that you are standing still with your
weight evenly distributed between both legs on the stainless steel electrodes.
Note: Your feet, legs, calves and thighs must not touch each other.
Otherwise the measurement cannot be performed correctly.The scale immediately begins to measure
your weight.
The scales begin weighing immediately. First, the weight is displayed. Whilst the further parameters are
being measured an „arrow on the left edge of the display“ appears (fig. 3).
Your measured weight is displayed shortly after this (Fig 4).
Measure weight, call up stored values, perform diagnosis
• Press the „[SET/ON]“ button on the control panel. The complete LCD display appears, then “- - - -“ is
displayed.
• Now press the button.
.
• Select the memory space where your personal data are stored by repeatedly pressing the
or keys
and confirm with „[SET/ON]“.
• Firstly your stored data are displayed consecutively, followed by the last measured values.
Firstly the following display appears.
1. Weight in kg
2. Body fat in % with interpretation of BF
3. Body water in %
4. Muscle percentage in %
5. Bone mass in kg
6. Active metabolic rate in kcal
Switching off the scale
The scale and the control panel switch off automatically after 10 minutes. While you adjust the settings it
takes 90 seconds before the control panel automatically switches off.
Hold the „[SET/ON]“ button depressed for 3 seconds to switch off the display module manually.
Make sure that you always switch on the scale first and wait for the display to show „0.0“ (Fig. 2) before
stepping on it.
Fig. 3
Fig. 4
0.0
kg
Fig. 2
----
Fig. 1
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanitas SBG 43 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanitas SBG 43 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info