Manual Sanibroyeur SANICUBIC 2 Pro (page 7 of 48) (All languages)

671246

Zoom out

Zoom in

1/48

DESCRIPTION

The SANICUBIC

2 Pro is a lifting station

designed to evacuate effluent from small

private or commercial units.

Please comply with all the installation

and maintenance specifications set out

in these instructions, and especially the

information marked with the following

signs:

» Failure to comply with this

information could entail safety

hazards for personnel,

» Information warning of the pre-

sence of an electrical hazard,

» Instructions only for qualified

professional specialists,

WARNING» Failure to comply with this

information could affect the normal

operation of the equipment.

Please contact our Customer service for

further information.

SANICUBIC OPERATING PRINCIPLE

SANICUBIC

2 Pro contains 2 separate

pumps. Each of the pumps is fitted with a

high-performance maceration system.

The 2 pumps operate alternately. In the

event of inflow overload, both motors run

at the same time (or if one of the pumps

is faulty, the other one takes over).

The SANICUBIC

2 Pro tank is fitted with

2 dip tubes; one tube controls motor

operation, and the other one controls the

alarm system.

- Long pickup tube (normal operation): as

soon as the waste water level in the tank

reaches the triggering point in the long

tube, the pumping system starts up.

- Short pickup tube (inflow overload

operation): if the waste water level in the

tank reaches the upper point, a contact

is closed, and the auxiliary pumping

system is triggered. The contact also

sets off an audible and visual alarm. The

general alarm LED on the SANICUBIC

2 Pro control panel switches to red. The

system sends a high-frequency malfunc-

tion signal to the remote alarm unit. The

SANICUBIC

2 Pro is fitted with a remote

alarm module that transmits a visible and

audible alarm (HF link).

LIST OF PARTS SUPPLIED

DIMENSIONS

TECHNICAL DATA SANICUBIC

2 Pro

Type R300

Maximum discharge head 11 m

Voltage 220-240V

Frequency 50 Hz

Volume 47 l

Maximum power input 3000 w

Maximum current input 13 A

Electrical classification I

Ave water temp for optimum performance 35°C

Maximum temperature (intermittent) 70°C*

Protection index IP67

Net weight (including accessories) 30 kg

Hot water drain cycles from dishwashers or washing machines

FIELD OF APPLICATION

Household waste water (the combined

inputs must not exceed 80% of those

shown in the graph

INSTALLATION

The SANICUBIC

2 Pro must be installed

in compliance with standard EN12056.

The equipment must be commissioned

and maintained by a qualified professio-

nal specialist.

Please refer to installation standard

EN 12056.

REGULATIONS

1- Attention: the space in which the

SANICUBIC

2 Pro is to be installed

must be large enough to leave at least

600 mm of working room around and

above the unit to facilitate such

maintenance work as may be required.

There must be sufficient lighting, and it

must be sufficiently well ventilated and

protected from freezing.

2- Isolating valves (not supplied) must

be fitted on waste inlets (especially

the 110mm inlets) and on the dis-

charge to ensure that any

service/maintenance may be carried

out safely).

3- The discharge pipe must be fitted

so as to avoid all back flow from the

drainage system (see the examples in

drawing

). Back flow can be avoided

by installing an anti-back flow riser

reaching a high point above the

maximum back flow level.

Comment: In the absence of local

information to the contrary, the

maximum back flow level corresponds

to street level (roadway, pavements,

etc.). Continue the discharge pipework

after the anti-backflow riser, using a

larger diameter pipe.

4- If the SANICUBIC is installed in a

space such as a pit for example, we

would recommend the fitting of a bilge

pump in case of flooding.

5- The lifting station must be vented with

an outlet at roof level.

6- The lifting station must be fixed to the

floor (see paragraph

CONNECTING THE DISCHARGE

PIPE

Remove the end cover or covers from the

back of the unit (cf.

As each pump is fitted with a macerator

system, an ND50 mm discharge pipe can

be used.

The discharge bend is at the centre of the

unit, at the back (cf.

). Use the sleeve

to connect it to the riser pipe and fix it

in place with the collars.

Each pump in the SANICUBIC

2 Pro

unit is fitted with check valves.

See paragraph

regarding control

valves and back flow.

CONNECTING SANITARY

EQUIPMENT TO THE LOWER

INLETS

If you want to install a shower or a

bath at the same level as the

SANICUBIC

2 Pro, you must

make sure that the upper parts of the

plugholes on the sanitary equipment are

at least 250 mm above the lower inlets.

CONNECTING THE INLETS ND

40/50

Lower inlets (cf.

)

Upper inlets (cf.

)

• Cut off the end of the ND 50 inlet with

a saw

• Cut the sleeve

to suit the pipe

diameter: ND 40 or ND 50 (cf.

)

• Fix the sleeve

on the inlet and on the

pipe, using the collars.

CONNECTING THE ND 100/110

INLET

Lower inlets (cf.

)

1- Remove the plug from the side inlet.

2- Fix the sleeve

in place using the

collar

3- Fully insert the ND 100/110 tube in

the other end of the sleeve and fix it in

place using the other collar

Upper inlets (cf.

)

1- Cut off the upper end of the ND 100

inlet with a saw.

2- Fix the sleeve

in place using the

collar

3- Fully insert the ND 100/110 tube in

the other end of the sleeve and fix it in

place using the other collar

CONNECTING THE VENT

The SANICUBIC

2 Pro must be vented

with an outlet at roof level.

Fix the sleeve

in place using the

collar

Fully insert the ND 50 tube in the other

end of the sleeve and fix it in place using

the other collar

WARNING: Do NOT fit air admittance

valve on the top of the air vent pipe. The

vent must be an open vent or the unit will

not operate.

PERFORMANCE CURVE

Example: Pump P1 is operating nor-

mally. It discharges 160 l/min at a pum-

ping height of 5 m. If pump P1 shows any

signs of weakness or if the waste water

inflow is too great, pump P2 starts up.

The output is then increased to about 275

l/min, until the situation returns to normal.

The numbers refer to the explanatory diagrams.

RATIO OF HEIGHT/LENGTH

FOR DISCHARGE

Fully illustrated step by step

instructions are downloadable

on www.saniflo.co.uk

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sanibroyeur SANICUBIC 2 Pro in the language / languages: All languages as an attachment in your email.

The manual is 2,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sanibroyeur SANICUBIC 2 Pro Manual

Product: