532742

Sanibroyeur SANICUBIC 1 Expert-line Manual

12
Zoom out
Zoom in
Previous page
1/79
Next page
DISMANTLING
16
WORK THAT MAY BE REQUIRED
15
ELECTRICAL INSTALLATION MUST BE CARRIED
OUT BY A PROFESSIONAL ELECTRICIAN
Before carrying out any other types of work, disconnect
the Sanicubic from the power supply.
UK
INSTRUCTIONS ONLY FOR QUALIFIED
PROFESSIONAL SPECIALISTS
UNIT ALARM
REMOVING A MOTOR
INSTRUCTIONS RESERVED EXCLUSIVELY
FOR QUALIFIED PROFESSIONAL SPECIALISTS
Unclip the cover.
Unscrew the collar on the
motor (the check valve
stays in place while the motor
is being repaired).
A
Unscrew the collar .
Remove the motor power
wires from the screw
connector.
C
B
Remove the screws from
the inspection cover.
Use the handle to lift the
motor carefully.
E
D
If the faulty motor has to be
sent back to the manufacturer.
PUTTING THE MOTOR
BACK IN PLACE
Re- assembly is the reverse
of the above.
Reconnect the motor power
wires (cf. illustration ).
Warning:
Comply carefully with the
colour code:
Blue wire with the blue wire
Brown wire with the brown
wire
Green wire with the green
wire
White wire with the white
wire
Connect the unit to the
power supply.
Carry out a complete test
for commissioning (cf.
paragraph ).
11
2
16
The unit beeps to show that it
is no longer under power.
PROBABLE CAUSES
Faulty electronic card
1 – Obstructed Dip tube
2 – Pump discharge height too
high
The non-return valve is
leaking or broken
SOLUTIONS
Contact SFA after-sales
service
1 – Remove obstruction from
the discharge pipe
2 – Check installation (**)
Clean or change the valves
Possible secondary maintenance operations
PROBLEM
No motor starts and the mains
GREEN LED is off (*)
The LED war
The LED flashing warning light
ning light is on
PROBABLE CAUSES
No power
1 – Obstructed pump
2 –
Faulty detection system
Blocked Pump
SOLUTIONS
Check your electrical
connections
Press the override button
continuously to get the
pump working
Contact SFA after-sales service
Possible preliminary maintenance operations on the unit
PROBLEM
The motor does not start
but override works + The LED
warning light on
Pump running continuously
Pump starting up
intermittently
(**) Warning: if pumping height is high, 90° elbows should be avoided.
F
4
16
1
16
2
16
3
16
DISCONNECT THE UNIT FROM THE
POWER SUPPLY (the green indicator
light must be off).
N°156 PRO
Alarm reset
The manual override (MO) button switches
off the red LED if the problem is solved
REMOTE ALARM MODULE
FAULT WARNING LIGHT TABLE
Fault
detected
RED LED ON
+ YELLOW
LED OFF
+ BUZZER
RED LED OFF
+ FLASHING
YELLOW LED
+ INTERMITTENT
BUZZER
Probable
causes
1- Blocked
pumps
2- Blocked pumps
3- Problems with
the electric
motors
4- Too much
water flowing in
5- Faulty circuit
board
Mains supply fault
on the appliance
Remedial
action
1- Contact SFA
after-sales
service
Check the
electrical install
(*) override
A
B
C
D
E
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanibroyeur SANICUBIC 1 Expert-line at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanibroyeur SANICUBIC 1 Expert-line in the language / languages: All languages as an attachment in your email.

The manual is 7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info