Manual Sanibroyeur SANICONDENS Pro (page 8 of 32) (All languages)

532746

Zoom out

Zoom in

1/32

CAUTION

SANICONDENS

Pro is a pump for lifting condensation

water from an air conditioning system, a condensation boiler

or from refrigeration units. Include a neutralisation device if

necessary (see the manufacturer’s instructions for your boiler).

The pump starts automatically and has a high level of

performance, safety and reliability provided that all the

installation and maintenance instructions described in this

notice are strictly followed.

Please take particular note of the information marked by :

» Indication that a risk of electrical origin exists,

« » Instructions for use only by qualified professionals.

OPERATING PRINCIPLE

SANICONDENS

Pro contains a pump. The tank of the

SANICONDENS

Pro is fitted with a float which controls the

operation of the motor. When the condensates enter the

tank, the pump starts up.

LIST OF DOCUMENTS PROVIDED:

see fig.2

DIMENSIONS:

see fig.3

SANICONDENS

Pro AREA OF APPLICATION AND

TECHNICAL DATA

Application

Air conditioning systems, boilers,

refrigeration units

Type CD10

Max. vertical pumping 4,5 m

Maximum flow rate (litres / hour) 342

Flow rate at 4 m 156

Min. pH 2,5

Voltage 220-240 V

Frequency 50 Hz

Power rating 60 W

Current consumption 0,52 A

Electrical class I

Protection index IP20

Sound level < 45 dBA

Average utilisation temperature 35°

Maximum allowable temperature 80°

S3 15% (90s ON, 510s OFF)

Net weight 2000 g

Tank volume 2 litre

Supply cable 2 m

Discharge hose 6 m

Alarm cable (3 core) 2 m

Wall fastening Yes

CAUTION:

All applications other than those described in this notice are

prohibited.

PERFORMANCE CURVES:

see fig.5

VERTICAL PUMPING/HORIZONTAL PUMPING:

see fig.6

INSTALLATION

SANICONDENS

Pro has wall fixings.

The unit should be easy to access for testing and

maintenance.

The unit must be installed level. Adjust the installation

using a spirit level before fixing the unit.

Make sure that the equipment is protected from damp while

installing it.

CONNECTION AT THE COVER INLET

The unit has 2 inlets 28 mm in diameter (1 on each side - see

fig.

). To connect the water to be drained off, connect the

water inlet to one of the inlets. If necessary, use the rubber

adaptator

19, 32, 40 mm.

CONNECTING TO THE DISCHARGE PIPE

The SANICONDENS

Pro discharge pipe must be connec-

ted to the flexible hose

(supplied : length 6 m). This hose

should be used to form the vertical section of the discharge

pipe.

• Place the flexible hose onto the non-return valve of the

SANICONDENS

Pro (see diagram

)

• Position the flexible hose in the most vertical position

possible to avoid it kinking.

• It is advisable to make a smooth bend to avoid the hose

kinking.

• The hose has a diameter of less than 8 mm and can be

connected to a PVC hose of larger diameter by a plastic

reducing connection on the horizontal section of the dis-

charge hose, or connected to your drain by a plastic redu-

cing connection

. In UK fittings such as Speedfit from

John Guest are available -part numbers PEM202215W

used with PEM06150W to connect to 22mm pipework.

The SANICONDENS

Pro is fitted with a non-return valve

to prevent re-activation.

ELECTRICAL CONNECTION

The electrical installation should be carried by a qualified person.

The unit should be connected to a fully earthed electrical

supply. All wiring must conform to BS7671, 1992 requirements

for electrical installations. The SANICONDENS

Pro requires a

220/240V single phase AC 50 Hz supply (UK specification). Do

not connect SANICONDENS

Pro to a conventional plug and

socket. It must be wired into a fused, unswitched, fixed wiring

connector fitted with a 5 amp fuse. SANICONDENS

Pro has

an Earth wire. The wires in the mains lead are coloured in accor-

dance with the following code:

Brown – Live Blue – Neutral Green/Yellow – Earth

Warning: Ensure the electricity is turned OFF at the main

switch board before wiring to connector.

All work on cable, pressure chamber and motor should only

be carried out by a qualified Saniflo servicing agent, as

special tools are required.

ALARM

SANICONDENS

Pro is fitted with a detection system

that can trigger an alarm if the water level rises too high

(audible or visual alarm, 1.5V to 230V), see diagram

. Brown wire: shared wire

. Black wire: normally off

. Blue wire: normally on

To fit the alarm, connect the blue and brown wires

of the alarm to the respective terminals on the

SANICONDENS

Pro.

INSTRUCTIONS INTENDED SOLELY FOR

QUALIFIED PROFESSIONALS

INSTRUCTIONS INTENDED SOLELY FOR

QUALIFIED PROFESSIONALS

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sanibroyeur SANICONDENS Pro in the language / languages: All languages as an attachment in your email.

The manual is 3,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sanibroyeur SANICONDENS Pro Manual

Product: