532726

Sanibroyeur SANICOMPACT 48 ECO Plus Manual

8
Zoom out
Zoom in
Previous page
1/40
Next page
8
1
DESCRIPTION
SANICOMPACT
®
Eco is a WC specially designed with
an integral pump/macerator. SANICOMPACT
®
Eco is for
domestic use.
Installed and used correctly, SANICOMPACT
®
Eco will give
consistent and reliable service.
Please note the following warning signs:
«
» Possible danger to personnel,
«
» Warning of possible electrical hazard.
«WARNING» This is a general warning that failure to
follow instructions could result in poor functioning
of the unit.
OPERATING PRINCIPLE
SANICOMPACT
®
Eco is controlled by an electronic
programmer.
It has a macerating and pumping function. To start press
one of the two grey sides (light grey: small flush, dark grey:
large flush) of the button integrated to the bowl.
2
LIST OF ACCESSORIES INCLUDED
3
DIMENSIONS
4
TECHNICAL DATA
Applications discharge of a WC
Type
CR15 DF
Maximum Vertical Pumping 3 m
Voltage 220-240 V
Frequency 50 Hz
Normal Power Rating 550 W
Maximum current consumption 2,5 A
Electric Class I
Degree of protection IP44
Maximum water temperature 35°C
Net Weight C3 28,6 Kg
C5 29,0 Kg
C6 26,5 Kg
C43 23,2 Kg
C48 25,4 Kg
WARNING: Only installations conforming to the above
specifications are acceptable.
5
PERFORMANCE CURVE
6
INSTALLATION
6a
ATTACHING THE TOILET TO THE FLOOR
Place the SANICOMPACT
®
Eco in the desired location.
Trace round the position of the bowl and mark the postition
of the fixing screws. Remove the bowl and then mark the
position of the fixing brackets 15mm inside the drawn line
(see dia
6a
).
Remove the toilet bowl.
Drill through the flooring.
If necessary, and if you have time, lay a silicone joint
around the location of the toilet bowl.
Install the fixing screws and brackets. Put the
SANICOMPACT
®
Eco in place. Use the screws to fix the
SANICOMPACT
®
Eco to the floor.
6b
CONNECTION OF THE DISCHARGE
1 - Fully insert the elbow
H
a
in the end of the rubber
waste tube, after turning it to face in the desired
direction.
2 - Fix the base of the elbow
H
a
and tighten it on the
rubber waste tube with a clamp
D
.
3 - Connect the sleeve
H
b
to the end of the elbow with
the clamp
D
. Cut off the end of the sleeve to adapt it to
the waste pipe. Connect the 32mm wastepipe into the
sleeve and secure with jubilee clip
C
.
4 - Warning: Ensure that you do not twist the discharge
pipework inside the unit.
5 - Warning: The horizontal portion of the discharge pipe
should be installed in a gravity flow, (1/4 inch to 1 foot).
Avoid any low parts in the discharge pipe.
6 - Warning: Protect pipes against freezing with appro-
priate insulation. If the toilet is installed in an unheated
location during freezing periods protect it as follows:
• Shut off the water supply,
• Activate one cycle without water,
• Pour antifreeze in the bowl (2 litres),
• Flush the toilet.
7 - Warning: Any bends in the discharge pipe run should
be smooth radius bends. If using plastic pipe two 45
degree offsets can be used to form a smooth bend.
8 - Note: We would recommend that a drain-off point is
installed to allow the discharge pipework to be drained
down before any service work.
9 - Note: To avoid siphoning, install a an anti-siphon valve
at the high point of the installation.
6c
CONNECTION TO THE WATER SUPPLY
Connect the water supply hose to a shut off valve
Caution: The quality of the rinsing of the bowl depends on
the water pressure.
WARNING: for a correct rinsing, the water pressure should
be at least 25 PSI (1,7 bars).
Note: In an area where water is not pure (dirty, sandy), we
advise you to add a filter between the shut off valve and the
toilet to prevent clogging of the solenoid valve.
6d
CONNECTION TO THE ELECTRICAL SUPPLY
The electrical installation should be carried by a
qualified person.
All wiring must conform to BS7671, 1992 requirements for
electrical installation. The unit requires a 220/240 V single
phase AC 50 Hz supply (UK specification). Do not connect
the unit to a conventional plug and socket. The unit should
be connected to a fully earthed electrical supply (class 1).
It must be wired into an unswitched fused fixed wiring
connector protected by a 5 amp fuse and a residual cur-
rent detector (30 mA). This connection must be used
exclusively for supplying the unit.
The wires in the mains lead are coloured in accordance
with the following code:
Brown – Live
Blue – Neutral
Green/Yellow – Earth
WARNING: Ensure the electricity is turned OFF at the main
switch board before wiring to connector. All work on cable,
pressure chamber and motor should only be carried out
by a qualified Saniflo servicing agent, as special tools are
required.
UK
Fully illustrated step by step instructions are
downloadable on www.saniflo.co.uk
9008 SANICOMPACT ECO N°107.indd 8 14/06/10 12:30:20
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanibroyeur SANICOMPACT 48 ECO Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanibroyeur SANICOMPACT 48 ECO Plus in the language / languages: All languages as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanibroyeur SANICOMPACT 48 ECO Plus

Sanibroyeur SANICOMPACT 48 ECO Plus Additional guide - Dutch - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info