577232
10
Zoom out
Zoom in
Previous page
1/16
Next page
10_Installation & maintenance
installation & maintenance
The User’s Manual is for common use. Make use of the User’s Manual depending upon your washing machine model.
ENVIRONMENT
Leave some space - Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface. - If the washer is placed on an uneven or weak surface, noise or
vibration occurs. (Allowable is 1˚) Adjust the legs for even placement.
Never install the washer near water. - Do not place the washer in steamy rooms or where the washer is directly exposed to rain.
Moisture may destroy the electrical insulation causing an electrical shock hazard.
Avoid direct sunlight or heaters. - As plastic an electrical components are affected by direct heat, never place the
washer near furnaces, boilers, etc. Do not place under direct sunlight.
LEVELLING
If the washer is not leveled with the ground, it makes the machine tremble more or be out of order.
So, make sure that the washer is leveled properly.
SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF
THE WASHING TUB.
Open the lid of the machine, pour water into the tub up to the level just
below the pulsator, and adjust the legs so that the pulsator is positioned
at the center of the water as shown in the figure.
Place the machine more than 10cm away from the wall.
Adjust the legs on feet for levelling.
CONNECTING THE WATER SUPPLY HOSE
1. Remove the adaptor from the
water supply hose.
4.
Connect the water supply hose to
the adaptor. Pull down the part (c)
of the water supply hose. When
the part (c) is released, the hose
is automatically connected to the
adaptor making a ‘click’ sound.
2. First, using a “+” type screw driver,
loosen the four screws on the
adaptor. Next, take the adaptor
and turn part(b) following the arrow
for gap about 5 mm between
them.
5. Connect the other end of the
water supply hose to the inlet
water valve at the back of
the washer. Screw the hose
clockwise all the way in.
3. Connect adaptor to the water
tap by tightening the screws
firmly. Then, turn part(b) following
the arrow and put (a) and (b)
together.
5-1. Connect the other end of
the water supply hose to the
inlet water valve at the top of
the washer. Screw the hose
clockwise all the way in.
If the water tap is a screw type, assemble a water supply hose that fits to the tap as shown.
After completing connection, if water leaks from the hose, then repeat the same steps.
After completing connection, if water leaks from the hose, then repeat the same steps. Use the most
conventional type of faucet for water supply.In case the faucet is square or too big, remove the spacing ring
before inserting the faucet into the adaptor.
Water
LOOSEN LOCK
a
b
c
WA85G5P-02898D-02_EN.indd 10 2011-08-23 �� 12:21:42
10


Need help? Post your question in this forum.

Forumrules
1

Forum

samsung-wa90w9

Reset search

  • Why the water not draining after the machine finish washing?. Drain not working? Submitted on 29-9-2020 at 09:17

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samsung WA90W9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samsung WA90W9 in the language / languages: English as an attachment in your email.

The manual is 2,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info