621307
47
Zoom out
Zoom in
Previous page
1/70
Next page
English _47
SETUP SCREEN
Alarm input
You can set the alarm input type, activation time, and operation mode.
1. From the Setup menu, select the <Event (
)> tab.
2. Click <Alarm input>.
3. Set whether or not to <Enable>.
4. Select the type.
Normal open : It is normally open, but if it is closed, an
alarm will be triggered.
Normal close : It is normally closed, but if it is open, an
alarm will be triggered.
5. Specify the <Activation time>.
Always : Always check if an alarm occurs. It activates in
operated mode when the alarm occurs.
`
If set to <Always>, the activation time cannot be changed.
Only scheduled time : Check if an alarm occurs at a specified day of the week for a specified time
period. It activates in operated mode when the alarm occurs.
[Clear (
)] : Reset all settings.
Minute : Click an area in Activation Time and set the time
by minutes.
Hour : Drag your mouse at Activation Time and set the
time by hours.
6. Specify an operation that will perform if an alarm occurs.
FTP : Specify the use of FTP transfer in the alarm input
setup.
`
Refer to “FTP / E-mail for more details. (page 43)
E-mail : Specify the use of email transfer in the alarm input setup.
`
Refer to “FTP / E-mail for more details. (page 43)
Record : You can set up the alarm to record to a Micro SD card or an NAS when operating.
`
Set <Device> to <On> in <Storage>. (page 44)
Alarm output : Select whether to set the alarm output if an alarm is incoming, and specify the alarm
output time.
7. When done, click [Apply (
)].
Time schedule
You can set to save the video data at a certain interval as scheduled regardless of the actual occurrence of
the event.
1. From the Setup menu, select the <Event (
)> tab.
2. Click <Time schedule>.
3. Set whether or not to <Enable>.
4. Specify the <Transfer interval>.
5. Specify the <Activation time>.
Always : Always activates in operated mode at the set
interval.
Only scheduled time : Periodically activates in operated
mode at a specified time and date.
J
`
The transfer interval setting value must be smaller than the preset
activation interval to succeed in image transmission.
6. Specify the activation conditions.
FTP : Specify the use of the FTP transfer if an event occurs.
`
Refer to “FTP / E-mail for more details. (page 43)
7. When done, click [Apply (
)].
Tampering detection
You can set to detect tampering attempts and trigger events, such as sudden change of camera’s framing
direction, blocked lens and other overall change of scenes from the video.
1. From the Setup menu, select the <Event (
)> tab.
2. Click <Tampering detection>.
3. Set whether or not to <Enable>.
4. Set the tampering detection sensitivity. The higher the
sensitivity, detects the minutest tampering attempts.
5. Specify the activation time and activation condition.
`
For more information about <Activation time> and <Action>, refer to
Alarm input”. (page 47)
6. When done, click [Apply (
)].
J
`
The default tampering detection function may not work properly in
the following cases:
-
Under circumstances of simple background or low illumination and night time may lower the detection sensitivity.
-
A severe shaking of the camera or a drastic change to the illumination can be considered a tampering by mistake.
-
Detection of the tampering may take some time (maximum 5 seconds) right after the tampering was made.
-
Once a tampering is detected, the camera will resume a normal operating after a certain stability time (approx. 5 seconds)
during which no detection will be performed.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samsung SNV-6085R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samsung SNV-6085R in the language / languages: English as an attachment in your email.

The manual is 21,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info