620903
13
Zoom out
Zoom in
Previous page
1/37
Next page
13
02
Installation & Network Connection
Precautions
The wireless network access may fail, depending on the communications
environment.
For details about the network settings and password, contact your network
administrator or service provider.
For a specific Internet service requiring user authentication, you may not access
the service. If this is the case, contact the service provider.
Do not access the unauthorized network.
The farther the distance from the Wireless Access Point, the longer time the
network connection may take.
If you fail to access the selected wireless network, try a different Wireless
Access Point to make access.
For more information about the router or the wireless connection, refer to the
documentation of the router or contact the router manufacturer.
If the camera is connected to a multiple-Wireless Access Point network
environment, some video packets may be lost, depending on the network traffic
load.
According to the network policy (blocking UDP) of the service provider, the video
transmission can be limited to 7 minutes.
For more details, refer to the descriptions on page 23, <Relay Mode>.
In addition to the above two situations, you may encounter a network delay or
interruption due to the network conditions.
Some hubs can have compatibility issues.
Network Connection and Settings
Connecting via network cable
If you do not have a Wireless Access Point, you must connect the camera using
LAN cable directly to your home router.
1. When you apply the power, the power status LED is lit red, and it will change
to red blinking when the booting is completed.
2. Connect the network cable to the camera and to the home router as shown
below.
3. The status LED will become steady blue once the camera is connected to
the router. (may take up to 30sec).
If the status LED (blue) is not lit, repeat steps 2 through the end and check it
again.
4. The status LED will became steady green once the camera is connected to
server.
n
` It is recommended to set the router to DHCP(Dynamic Host Configuration Protocol)
server.
If you want to use static IP address, please refer to <Wired Network> on page 24.
` If the router’s UPnP is not set, then you might be connected in relay mode.
The settings may differ depending on the connected Broadband Router model.
For more information, refer to the user manual of the applicable router.
DC IN 5V
SAMSUNG SMARTCAM
NETWORK
RESET
Internet Service
<Modem>
<Hub>
OR
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samsung SNH-1011N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samsung SNH-1011N in the language / languages: English as an attachment in your email.

The manual is 8,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samsung SNH-1011N

Samsung SNH-1011N Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info