684519
32
Zoom out
Zoom in
Previous page
1/47
Next page
32
Wall
<20mm
Plastic
Anchor
Fixing the installation plate
2. Fix the indoor unit.
If you x the indoor unit on a wall
(1) Fix the installation plate to the wall giving attention to the weight of the indoor unit.
If you x the indoor unit on a window frame
(1) Determine the positions of the wooden uprights to be
attached to the window frame.
(2) Attach the wooden uprights to the window frame giving
attention to the weight of the indoor unit.
(3) Attach the installation plate to the wooden upright using
tapping screws.
If you x the indoor unit on a gypsum board
(1) Use stud nder to nd out locations of the studs.
(2) Fix the plate hanger on two studs.
• Ifyoumounttheplatetoaconcretewallusingplasticanchors,makesurethatgaps
between the wall and the plate, created by projected anchor, is less than 20mm.
• Searchforotherspotsiftherearelessthantwostuds,orthedistancebetweenthestudsaredierentfromthe
plate hanger.
• Fixtheinstallationplatewithoutincliningtooneside.
• Makesurethatawallcanwithstandtheweightoftheproduct.Ifyouinstalltheproductinaplacewhereitisnot
strong enough to withstand the product weight, the unit could fall and cause injury.
Connecting the assembly cable
• Connectthepowercableto
the auxiliary circuit breaker. If
every pole fails to connect to
the power supply, it must be
incorporated in a wire with a
contact opening of ≥3mm.
Model Power cable Interconnection cable
Type GL
AR09/12FSFP
3G, 2.5mm
² H07RN-F
3G, 1.5mm² H07RN-F
20A
2* 0.75mm
² H05RN-F
AR18/24FSFP
3G, 2.5mm
² H07RN-F
3G, 1.5mm² H07RN-F
25A
2* 0.75mm
² H05RN-F
Cable speci cation
Connecting the cable
If using a multi system, install as described in the installation manual supplied with the outdoor unit.
Electrical work
(1) For electrical and earth works, comply with the ‘technical standards of electrical installations and the the wiring
regulations of the Electricity Enterprises Act.
(2) Tighten the terminal block screw to under 12kgf.cm.
(3) Precautions when connecting terminal blocks of the indoor unit
Before connecting, make sure the connecting part of the terminal socket is facing upwards.
Upside down
The terminal
socketis damaged.
There is no ring
terminalto cover the wire.
There must be no space between the terminal and the screw when connected.
- Any remaining space may become a re hazard due to overheating of the electrical contact.
The terminal socket is
upside down.
Either the screw is not fitted
properly or there is a space between
the screw and the ring terminal.
•
For the terminal block wiring, use a wire with a ring terminal socket only.
Regular wires without a ring terminal socket may become a re hazard due to overheating of the electrical contact during a wiring work.
Maldives ET_AR09FSFP@_IBIM_DB68-03376A_EN_2.indd 32 2012-12-3 18:54:50
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samsung AR24FSFP Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samsung AR24FSFP Series in the language / languages: English as an attachment in your email.

The manual is 10,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info