629982
16
Zoom out
Zoom in
Previous page
1/32
Next page
XML POWERED MIXERS
16
Speaker Outputs - XML410
The XML410 contains two mono power ampliers, and depending on the operating mode, the two ampliers can be
used independently (maximum output 200W + 200W) or in BRIDGE mode (maximum output 400W).
NOTE: Use the front panel Power Amp MODE switch to select which signal is sent to the speaker output jacks, and to
activate BRIDGE mode.
If the two power ampliers are used for MAINS operation, two 8 Ohm speakers can be daisy-chained” together and con-
nected to the AMP 1 jack, and two more 8 Ohm speakers can be daisy-chained” together and connected to the AMP 2
jack, for a total of four speakers.
The total impedance load for each amplier must not exceed 4 Ohms. Therefore, in the example above, two speakers with
an impedance of 8 Ohms each are connected to each amps output jacks.
If you wish to use two ampliers independently, lets say for Main and Monitor operation, use a 4–8 Ohm speaker. Again,
the total impedance load for each amplier must not exceed 4 Ohms. Therefore, two speakers with an impedance of 8
Ohms can be daisy-chained” together and then connected to each amps output jacks.
If two ampliers are used in a BRIDGE mode, only one speaker can be connected to the BRIDGE jack. The total impedance
load while operating in BRIDGE mode must not be less than 8 Ohms. If you are connecting a speaker to the BRIDGE jack,
use an 8–16 Ohm speaker.
CAUTION: When using a BRIDGE connection, do not connect anything to the AMP 1 and AMP 2 jacks. Likewise, when us-
ing the AMP 1 and AMP 2 jacks, do not connect anything to the BRIDGE jack.
44. AMP 1 Speaker Outputs - The AMP 1 output has one 1/4” phone connector, which is a powered output used to con-
nect your main PA speaker when using the XML410 in MAIN/MAIN mode. When operating in MAIN/MONITOR mode,
the AMP 1 powered output connectors are used to connect left and right side MAIN PA speakers.
45. AMP 2 Speaker Outputs - The AMP 2 output has one 1/4” phone connector, which is a powered output used to con-
nect your main PA speaker when using the XML410 in MAIN/MAIN mode. When operating in MAIN/MONITOR mode,
the AMP 2 powered output connectors are used to connect to oor or side ll monitors facing the performers.
46. BRIDGE Output connector - The BRIDGE output has one 1/4” phone connector, which is a powered output used to
connect one main PA speaker when using the XM410 in BRIDGE mode.
44 4546
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson XML410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson XML410 in the language / languages: English as an attachment in your email.

The manual is 7,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samson XML410

Samson XML410 User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info