629820
13
Zoom out
Zoom in
Previous page
1/20
Next page
9
The SZ Series Protection Circuitry
As noted in the “Guided Tour section of this manual, the SZ Series front-panel
Protection LED indicates the activity of the relay speaker connection circuitry. When
the Protection LED is lit, this circuitry is active, and all connected speakers are muted.
The following conditions will cause the Protection LED to go on:
• Initial power-up: For approximately five seconds after initial power-up, the protec-
tion circuitry is activated and the speaker outputs are muted. If everything is operat-
ing normally, the SZ Series begins delivering signal to connected speakers (at which
point you’ll hear the click). It is normal for the Protection LED to fade gradually after
the amplifier is powered off.
Overheating: A temperature sensing device in the SZ Series will cause the protection
circuitry to be activated (and the Protection LED to go on) whenever the operating
temperature of the unit rises above a safe level. To guard against this problem, make
sure the SZ Series receives adequate ventilation on all sides and that both the front
and rear panels are unobstructed.
• Severe over current conditions: This occurs whenever the signal being output from
the SZ Series rises to a level above 20% THD (Total Harmonic Distortion).
• Shorted speaker cables: This will occur if, due to faulty wiring, the hot and ground sig-
nals being output by the SZ Series are shorted to one another.
• Output impedance drops below 2 ohms: This can occur if the SZ Series is connected to
inappropriate speaker systems (see the “Setting Up and Using Your SZ Series” section
on page 10 in this manual for more information).
In general, any time the Protection LED lights up (other than during the approxi
-
mately five seconds following initial power-up), there is reason to be concerned. If this
occurs, turn the SZ Series off immediately and carefully check all wiring and external
devices in order to locate and correct the condition that caused the LED to light up in
the first place.
For further assistance, contact your local Samson dealer. If purchased in the United
States, you can call Samson Technical Support (1-800-372-6766) between 9 AM and 5
PM EST.
WARNING: If the Protection LED fails to go out (and you fail to hear the accom-
panying audible click) approximately five seconds after power-up, turn the SZ
Series off immediately and check all external devices and wiring for possible
shorts or other defects.
PROTECT
CLIP
-20 dB
SIGNAL
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson SZ1240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson SZ1240 in the language / languages: English as an attachment in your email.

The manual is 3,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info