629749
9
Zoom out
Zoom in
Previous page
1/16
Next page
9
SXD Series Power Amplifiers with DSP
Getting Started - DSP
The SXD power amplifier features sophisticated high-performance DSP with control for the input and output routing, filter
network, EQ, limiter, and time alignment delay. Follow these steps to navigate through the SXD internal DSP settings:
1. Turn the SXD power ON. The startup screen will be displayed (figure 1).
2. Press the UP & DOWN buttons to step through the DSP parameters (figure 2).
3. Rotate the EDIT knob to adjust settings. A box will flash in the upper right corner when a set-
ting has been changed (figure 3).
4. Press the EDIT button to confirm and set the changes. Press any other button to cancel the
adjustment.
5. Press the BACK button to exit out of a parameter and return to the top level of the menu.
DSP Settings
Preset - Choose either Manual Mode, which provides access to the full set of adjustable parameters, or from the four speak-
er presets: 2 full range, Mono 2-way, Sub/Sat, or 2 subs.
I/O - The I/O screen adjusts the settings for how the inputs will be routed through the DSP to the output connectors.
Stereo: Ch A Input -> Ch A Output & Ch B Input -> Ch B Output
Mono A+B dual: Ch A and Ch B inputs are mixed together, each level control adjusts the corresponding output level
Mono A+B link: Ch A and Ch B inputs are mixed together, Ch A level control adjusts both Ch A and Ch B output levels
Parallel A dual: Ch A input is sent to both Ch A and Ch B outputs, each level control adjust the corresponding output level
Parallel A link: Ch A input is sent to both Ch A and Ch B outputs, CH A level control adjusts the output level for both chan-
nels.
Filter (Manual mode) - The filter section allows you to build you own crossover or add speaker protection by stetting the
filters to remove the upper and lower limits of the audio bandwidth.
Filter Ch A - Press the Edit button to enter the filter parameters for channel A.
Filter Ch B - Press the Edit button to enter the filter parameters for channel B. If the Ch A filter is On, then the Ch B filter
can be set to the same settings by choosing A=B
LPF Freq - Rotate the EDIT knob to adjust the low pass filter frequency.
LPF Slope - Rotate the EDIT knob to adjust the filter type and slope roll off in dB per octave.
HPF Freq - Rotate the EDIT knob to adjust the high pass filter frequency.
HPF Slope - Rotate the EDIT knob to adjust the filter type and slope roll off in dB per octave.
X-Over (speaker preset) - When using a speaker preset, the filters are already configured for a crossover. This allows you to
easily set the crossover frequency for your speaker configuration.
Gain Offset (Manual mode) - This adjustment allows you to set an overall balance between the outputs of the amplifier. This
allows you to match the difference of output level of the speakers in a system without needing to constantly adjust the front
panel level controls.
GAIN OFFSET EQ LIMITERFILTER DELAY SETUPI/O
A
B
A
B
PRESET
DSP Flowchart
Samson
SXD7000
figure 1
I/O
Parallel A link
figure 3
P
R
E
S
S
T
O
R
E
S
E
T
figure 2
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson SXD3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson SXD3000 in the language / languages: English as an attachment in your email.

The manual is 5,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info