629749

Samson SXD3000 Manual

6
Zoom out
Zoom in
Previous page
1/16
Next page
6
Getting Started with the SXD Power Amplier
Setting up your SXD Series is a simple procedure which takes only a few minutes:
Remove all packing materials (save them in case your units needs future service) and decide where the amplifier is to be
physically placed—it can be used free-standing or mounted in a standard 19” rack, requiring two rack spaces. When in-
stalled, make sure that both the front and rear panels are unobstructed and that there is good ventilation around the entire
unit.
Make the speaker connections, using the binding posts, or Speakon® output connectors
on the rear panel. It is never a good idea to power up any amplifier that is not connected to
loudspeakers.
Next, make the signal input connections, using the input connectors on the rear panel (if
operating the SXD Series in Ch A Parallel mode, use the Ch A input only). If your mixer has
balanced outputs, we recommend the use of three-conductor cabling and connectors.
On the front panel of the SXD Series, turn both Channel level controls fully counterclockwise (to their “MIN” setting). Then
connect the supplied heavy-gauge 3-pin “IEC” cable to the rear panel IEC connector and to any grounded AC socket.
Turn the Power switch ON.
Apply an input signal to the SXD Series at or about +4dBu
(if sending signal from a mixer, drive the output meters at
approximately 0 vu). While the input signal is present, slowly
raise the Channel level controls until the desired sound level
is achieved. The SIGNAL and Limiter LED indicators next to
each Channel input control will show you the continuous power
output of the SXD Series as signal is being passed. For the
best signal-to-noise ratio, the SXD Series should normally be
run with the Channel Input controls at or near maximum (fully
clockwise, at the “MAX” position) and the LIMITER segments
should light occasionally (but not frequently) during peak
levels. If you are using a mixer that has a master output level
control, use it to attenuate the signal as necessary to achieve
the desired speaker level.
P
R
E
S
S
T
O
R
E
S
E
T
P
R
E
S
S
T
O
R
E
S
E
T
P
R
E
S
S
T
O
R
E
S
E
T
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson SXD3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson SXD3000 in the language / languages: English as an attachment in your email.

The manual is 5,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info